94 Mazda B4000. V6 4x4 manual
After engine has ran about an hour, I make a stop at location, then on startup engine has a hard time staying idle after engine it's warm. Cold start idles fine, hot start it dies out. I must rev gas for truck to stay on. What could this be?
I'm having trouble with my ford ranger. It cold starts fine, and drives fine while cold. Once it warms up the idle is barely keeping it running, or surging 1000-1500 rpms above normal idle. Any gas I apply while hot idling will stall out the motor, and will not restart. It acts like it is very flooded when I try to do a hot start. I pulled the IAC valve off and cleaned it even though it was very clean and actuated properly. I also cleaned my MAF, and that changed nothing. I really do not want to just throw parts at it hoping I guess right before I'm broke. Not sure where to go from here, and I live in Alaska where I am fixing this outside.
View 1 RepliesOle girl finally let me down, or I let it down at 224,000mi. Started just fine one early cold morning and in about 30 seconds started stumbling and down for the count she went. Acts like it wants to run but will only stumble.
Checked inertia switch (ok) and all vacuum lines/caps appear to be fine. I was kind of due for new set of plugs/wires and a fuel filter. Replaced all didn't see any problems with the old when pulling. She will run for a few seconds, but stumbles and not smooth while running. Checked fuel pressure KOEO 40psi steady. I can hear fuel pump charge system per as usual.
Seeing as it is super cab checked for chafing on wiring to fuel pump under cab. Looks fine. I've heard tell could be alternator, which seems odd to me. Wondering if it would be worth pulling it off and taking it in for a bench test? Maybe I missed something. I know the intake gasket is suspect.
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesI have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
94 Ford Ranger 2.3L
I started to have a slightly rough idle a while back, but not severe. I figured she was just aging a bit.
Changed plugs. Check engine light came on. Changed plug wires. Then I had a couple of episodes where it started to lose power and idle really rough (stalling). Both times it stopped after a few minutes. Had code read- they said it was coils. Replaced ignition coils. Check engine light still on, but it went a few weeks without power loss.
Tonight the loss of power returned and didn't leave, and I had a glowing red catalytic converter after I limped home 20 miles (hope I didn't do any serious damage, I was stranded.)
Found this post : [URL] .... But there's no resolution.
So, I'm probably dealing with a misfire, and I'm sure I torched my cat after tonight. So any other easy diagnose/fixes for a misfire? I'm a shade tree mechanic- so I know just enough to get myself in trouble. If I can't get a resolution soon it will be off to the mechanic (which, maybe I should have done 1st...)
I have a 94 Ford Ranger 4x4 4.0 V6. It has developed a rough idle and has lost i fair amount of power. I cleaned the maf sensor and iac valve. Along with replacing an o2 sensor that was reading bad, with no improvement. The guys at O'reilly took a look and think I may be dealing with a timing issue or a warped valve. My question here is to found the culprit? I'm very inexperienced at working on vehicles and am damn intimidated by the scale of a project like timing. I should add that while traveling on the highway in high gear at low rpms, it develops a rough stutter. I can either power through it or ease off to get it to stop, but it resumes shortly after. It almost acts like an egr valve stuck open when on the highway. But that doesn't account for the rough (a consistent put, put, put...) idle.
View 4 RepliesI've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...
Here's the part that has me confused... pulled codes yesterday using a innova scan tool...
koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....
How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....
I have an 87 ranger that has started having problems over the last week or so. I had a similar problem a year or so ago. I put a new fuel pressure regulator on and it fixed it. So it started acting up again so I got another regulator and it didn't work at all. It won't idle at all without dying. The motor revs up then cuts out completely and dies. It's like I'm repeatedly pressing the gas pedal when I do get it to idle but I'm not touching it at all. It runs fairly well on the road until I let off the gas then it goes to shaking and jumping up and down till I get back on the gas.
A guy told me to unplug a little cigarette pack shaped plastic box and see if it changed anything. I think he called it a map sensor? But that didn't do anything. I was thinking maybe the fuel filter was clogged up but I don't really know. It is fuel injected 2.9 4x4 regular cab. About 110000 miles. Not sure if filter has ever been changed. It doesn't smoke or smell like gas so I'm thinking it's starving for fuel.
I have 1994 ranger 2.3 2wd will not start when key is turned to start position - when clutch is depressed there is a click from fender mounted solenoid but it never cranks motor or starter--I need wiring diagram to trace origin of wire on starter solenoid because it does not have 12volts on it--when I jumper 12v on it and have it in neutral it starts up and runs but no voltage and no start with key....
View 2 RepliesI have a 1994 Ford Ranger 4.0L 4x4, 130,000. I love this truck but about a year ago it started not starting after it warmed up short distances in the summertime? It start right up on cold crank...Runs smooth idles like a champ...but if i shut it off..wont start for 20 to 40 min??? It doesn't happen in the winter months??? So I changed the fuel pump, filter, relays. I feel like it has something to do with the Ignition Control Module. Would that come up in a code?
View 13 Replies94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 RepliesI am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 RepliesMy kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
My son's Ranger wouldn't start today, turns over fine, added gas to make sure it wasn't out still no hit.
Other than fuel pump (he said he couldn't hear it) what things should he check? I'll check back in the morning.
1994 Ranger 2.3 4 Speed ....
Sons 94 ranger 4.0 4x4 Auto 185k got him to work yesterday but would not start to bring him home. No spark, checked with timing light, and no fuel pressure. Searched and read alot of tips from Pawpaw so I tried a few things with no luck. Swapped the relays around, inspected coil pack and plugs. CEL was not on and goes out while cranking. I have a OBD scan tool but this truck must be too old or I need finding plug. Crank sensor maybe?
View 7 Replies1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 RepliesI've got a '94 Ranger with the 4.0L OHV and an Automatic trans. When I start, hot or cold, it has quick lifter knock for only a fraction of a second. This same knock comes back if I hold the throttle over 3K with NO LOAD on the engine. With any load, I cannot make it knock. With no load, though, it becomes very loud, especially with more RPMs. at idle and slightly above, there is a slight tick that can only be heard with the bonnet up, and then it is only slightly noticeable. I think that this tick is unrelated, but I figured I should share that information. For oil, I run Pennzoil high mileage 10W-30, changed 3000 miles religiously. Purolator filter, PL30001. I can understand the startup knock, but I can't see why it seems to produce the same knock at high RPMs under NO load.
View 4 RepliesThe truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 RepliesMy son bout his first truck yesterday. 98 ranger sc 4x4 auto 4.0. Beautiful shape 139000 miles. got it cheap as it has issues. its been parked for a year. It has a surging idle when you start it up. rev it to 2500-3000 rpm and it idles fine turn it off and restart it surges again until you rev it. When we test drove it it ran like it was running out of gas/bad fuel pump, sputter at full throttle but accelerate at part throttle. Gauge said under 1/4 tank of gas. We put 3 gallons of gas in it when we got home and it seems to run fine now other than the idle surge. it had a 174 code(lean bank) but if it was running out of gas it should pull a lean code right? I am thinking IAC or intake leak.
View 9 Replies1999 mazda B4000 4WD 178000 miles 5 speed manual, I've been having a crank no start problem but after a few tries it would start, a week or so ago it was really cold (23) it wouldn't start so I opened the air box and shot it with starting fluid it took about 5 long sprays but it started.
It ran up op 3200 rpms and won't go back down, took it to my shade tree mech. he hooked it up to the diagnose thing it showed no codes, he poured water over the motor it different places and toward the back it idled down for a second so he says "blown intake gasket' so we replace upper and lower and sure enough we could see where there was a bad spot on the upper and a cleaner spot on the port.
That was not the problem it still idles at 3200, I mean wide open screaming, could the starting fluid have done something? Now he says "blown head gasket" I never had any idle problems before matter a fact besides the hard starting problem that started it was running just fine, what happened?