I noticed that my turn signals stopped working. I replaced the flasher. Now the turn signals work but the signal indicators in the dash don't light up. Also, the hazard lights don't work either. No flashing, no blinking when I turn on my hazards. I've seen many variations while searching? 1994 B3000 2x4 extra cab.....
View 14 RepliesI recently got a pretty cherry 98 Ranger 3.0 2wd extended cab auto. So far all it has needed was wiper blades, floor mats and a heater blend door. Last week my daughter informed me that the flashers and the turn signals stopped working. I looked for blown fuses and then took the low road and just bought a new flasher (my alldatadiy manual showed that the flasher was common to the turn signals and the hazard flashers so I took a shot at just throwing a part at it). That didn't fix it or else. Any pointers?
View 3 RepliesMy blinkers started off blinking a few times then stopped working, now they don't work at all. The fuse says it goes to the brake lamps, hazards and turn signals. The hazards work as well as the brake lamps. I found the relay/flasher box and it appears the relay and flasher is the same for both the turn signals and the hazards. I checked for the wire/connector problem in the column and all looks good there. When I activate the turn signal lever I feel one click in the relay/flasher which leads me to believe the turn signal switch is working. I went ahead and replaced the relay with no results. Is the flasher internals the same for both the hazards and the turn signals or is there two independent sections inside for each?
View 4 RepliesI have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 Replies98 4wd extended cab. So weird only the right side is not working. Lights in the dash to the lights outside everything is dead.
Fuses that I could find are good. We replaced the mf switch a few months ago.
The turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 RepliesMy AC clutch, radio, cruise control, and turn signals are not working. I have checked all fuses and relays that I can find, all good. From what I have read, these are not part of the GEM function. What I need to check next!
View 7 RepliesI have a 2003 Excursion 7.3 2WD Limited and all of the sudden experienced a number of issues all at once.
1. Turn signals stopped flashing (hazards still flash)
2. Lost Rear back up sensors
3. Lost overhead trip computer
4. Lost Rear A/C - switch does nothing
5. Front A/C now only blows through the defroster vent
I've checked all the fuses and cant find any bad ones.
I replaced the multi-switch flasher and turn signals still dont work - only hazards.
I drive a 98 Ford Contour Sport. When I was driving today, I signaled a left turn, and the signal began working erratically. This also happened with a right turn, and, since I deliver sandwiches, happened when I turned my hazards on. Throughout the day it got worse, and eventually stopped working. I'm willing to bet that it's a wiring issue since all of my fuses are fine.
View 5 RepliesComing back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 RepliesSo I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesSo I get to explore my first repair with this new to me car. Yesterday morning, turn signals works fine. That afternoon, the stalk apparently stopped working, which I have heard of. Interestingly though:
-the brights and cruise work
-the hazards work (my improvised indication that I'm turning )
-the stalk had been replaced once before by the PO.
Did this thing eat another stalk, or are there some other things I should check first?
I own a 1999 F350 CC SRW w/ 7.3L PSD engine. My turn signals stopped working suddenly. I've checked the fuse panel under the dash but it doesn't show any fuse for the turn signals.
My hazards do work although I noticed something very strange. When I tilt the steering column down the hazards stop working and when I tilt the column all the way up they work again. Still no turn signals though.
Having a problem with the brake lights. When the brake pedal is pressed, the running lights (including dash lights, parking lights, and the low power filament in tail light) turn on, but no brake lights. When the lights are turned on and brake pedal is pressed, the brake lights do not turn on at all. The 4 way flashers and signal lights work correctly with lights on and off. Things I have tried:
Replaced the tail light bulbs.
Checked fuses (#5, #10).
Disassembled the brake switch and bypassed it with a jumper wire.
Checked the grounds (tail lights, rear ground, drivers inner fender).
Tried to trace the wiring. Didn't see any noticeable damage, but the wiring is in a loom so it is hard to see.
Used contact cleaner on brake switch, rear wiring harness, body harness.
Still hoping it may be something simple that I've overlooked.
I used the volt meter wrong while testing my turn signal bulbs for power and not they do not work (or hazard lights).
View 3 RepliesI own a 2004 hyundai santa fe and just recently my turn signals have stopped working. My bulbs are fine because they still light up when I lock my car and my hazards work too. The flashing arrows on my dashboard wont show up for my turn signals but they will show up for hazards. I checked the fuse and its completely fine. I am so confused with what is wrong. The only thing I was doing before was messing with my new head unit which involved unplugging a lot of the stereo and fog lights and hazards but that all should have no affect on my turn signals.
View 6 RepliesThe issue I am now experiencing is my passenger headlight would only turn on once in a while . The driver side headlight would work just fine both high beam light also . Today I opened my hood I verified the cable had a poor ground to the headlight I noticed a burnt smell after checking the cables . I turned on my high beams both sides turn on . Then out of no where my turn signals both (Left - right - back and front stopped working. Including the Hazard lights both front and back). The cluster would not show neither turn signals turning on ( left-right ) I noticed that my headlight turn signal on the passenger side would turn on but not blink it would stay dim only when . I pushed the hazard light button . My cluster would show the right turn signal ( no clicking no flashing arrow ). The driver side would not work either. What can I do to fix the problem? I know that I will not be able to drive the car due to the issue.
View 5 RepliesLast weekend my headlights, wipers, turn signals, AC, and horn stopped working. Through searching and another post I narrowed the issue down to my ignition switch. After taking apart my steering column and getting the switch out, I found this...
The house which is connected to the switch, with the one of the red wires obvious fried....
So I'm hoping this problem and I'm wondering who else has had this happen. When I took apart the ignition switch itself, nothing appeared to be damaged. No burns no broken pieces, etc. the metal post on the outside corresponding to the fried wire on the housing was corroded, but that was it.
I think I need to replace the housing since all that plastic melted and I chipped it away to get to the connector. I can't seem to get the connectors on the wire off of the metal connectors that are supposed to be in the housing.
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 RepliesThe truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 RepliesA few days ago my speedometer stopped working. Then yesterday all of my gauges stopped working, as well as my turn signals. If this is a fuse issue then which fuse it is?
View 9 Replies