Ford Ranger / B-Series :: 1994 - Truck Won't Turn Over Just Making Noise Like It Wants To Start
Sep 12, 2005
The truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 Replies
Advertisement
My 99 ranger has just hit 111,000 miles. I'm getting a weird sound from the front right whenever I turn the truck slightly to the right. I don't hear it if it's leaning left. Is this likely the wheel bearing? I've heard these rangers are not best known for the quality of the wheel bearings.
View 14 Replies
I have a 1994 Ford Ranger Supercab with 180,000 miles, 4.0ltr 6cyl and it is in relatively good condition. When I bought the truck the check engine light was on. The previous owner said that it was something in the gas tank that has gone bad but it was not a big deal and the truck could be driven with no problems.
My mechanics have tried several times to read the error code but their diagnostic tool won't tell them what is wrong.
I have noticed over the past few days that when I am slowing down and riding the clutch (I was making a u-turn this morning) that the truck will shut off. It starts right back up but it keeps happening.
I have been considering replacing the IAC, new spark plugs, rotor and wires and fuel filter but I am not 100% this will fix my problem. I am NOT a mechanic but know plenty of them so it will be a situation where I buy the parts and a buddy puts them in.
View 9 Replies
Having a problem with the brake lights. When the brake pedal is pressed, the running lights (including dash lights, parking lights, and the low power filament in tail light) turn on, but no brake lights. When the lights are turned on and brake pedal is pressed, the brake lights do not turn on at all. The 4 way flashers and signal lights work correctly with lights on and off. Things I have tried:
Replaced the tail light bulbs.
Checked fuses (#5, #10).
Disassembled the brake switch and bypassed it with a jumper wire.
Checked the grounds (tail lights, rear ground, drivers inner fender).
Tried to trace the wiring. Didn't see any noticeable damage, but the wiring is in a loom so it is hard to see.
Used contact cleaner on brake switch, rear wiring harness, body harness.
Still hoping it may be something simple that I've overlooked.
View 10 Replies
I have a 98 Ranger 4x4 XLT 4.0 5sp. It has 182K miles.
Once in a while it will blow the fuel pump fuse. It'll go 2 years sometimes. And sometimes the engine will stall just for a second making the truck "buck" as it accelerates.
Could it be the pump is about to fail? How long do they normally last? Btw, I change my fuel filter every 2 years, no issue there.
I've owned the truck since new and maintenance is always taken care of. Also, What's the best way to change the pump?
View 9 Replies
I have 1994 ranger 2.3 2wd will not start when key is turned to start position - when clutch is depressed there is a click from fender mounted solenoid but it never cranks motor or starter--I need wiring diagram to trace origin of wire on starter solenoid because it does not have 12volts on it--when I jumper 12v on it and have it in neutral it starts up and runs but no voltage and no start with key....
View 2 Replies
I noticed that my turn signals stopped working. I replaced the flasher. Now the turn signals work but the signal indicators in the dash don't light up. Also, the hazard lights don't work either. No flashing, no blinking when I turn on my hazards. I've seen many variations while searching? 1994 B3000 2x4 extra cab.....
View 14 Replies
I have a 1994 Ford Ranger 4.0L 4x4, 130,000. I love this truck but about a year ago it started not starting after it warmed up short distances in the summertime? It start right up on cold crank...Runs smooth idles like a champ...but if i shut it off..wont start for 20 to 40 min??? It doesn't happen in the winter months??? So I changed the fuel pump, filter, relays. I feel like it has something to do with the Ignition Control Module. Would that come up in a code?
View 13 Replies
94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 Replies
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
View 4 Replies
My son's Ranger wouldn't start today, turns over fine, added gas to make sure it wasn't out still no hit.
Other than fuel pump (he said he couldn't hear it) what things should he check? I'll check back in the morning.
1994 Ranger 2.3 4 Speed ....
View 3 Replies
94 Mazda B4000. V6 4x4 manual
After engine has ran about an hour, I make a stop at location, then on startup engine has a hard time staying idle after engine it's warm. Cold start idles fine, hot start it dies out. I must rev gas for truck to stay on. What could this be?
View 1 Replies
I'm having trouble with my ford ranger. It cold starts fine, and drives fine while cold. Once it warms up the idle is barely keeping it running, or surging 1000-1500 rpms above normal idle. Any gas I apply while hot idling will stall out the motor, and will not restart. It acts like it is very flooded when I try to do a hot start. I pulled the IAC valve off and cleaned it even though it was very clean and actuated properly. I also cleaned my MAF, and that changed nothing. I really do not want to just throw parts at it hoping I guess right before I'm broke. Not sure where to go from here, and I live in Alaska where I am fixing this outside.
View 1 Replies
Sons 94 ranger 4.0 4x4 Auto 185k got him to work yesterday but would not start to bring him home. No spark, checked with timing light, and no fuel pressure. Searched and read alot of tips from Pawpaw so I tried a few things with no luck. Swapped the relays around, inspected coil pack and plugs. CEL was not on and goes out while cranking. I have a OBD scan tool but this truck must be too old or I need finding plug. Crank sensor maybe?
View 7 Replies
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies
I've got a '94 Ranger with the 4.0L OHV and an Automatic trans. When I start, hot or cold, it has quick lifter knock for only a fraction of a second. This same knock comes back if I hold the throttle over 3K with NO LOAD on the engine. With any load, I cannot make it knock. With no load, though, it becomes very loud, especially with more RPMs. at idle and slightly above, there is a slight tick that can only be heard with the bonnet up, and then it is only slightly noticeable. I think that this tick is unrelated, but I figured I should share that information. For oil, I run Pennzoil high mileage 10W-30, changed 3000 miles religiously. Purolator filter, PL30001. I can understand the startup knock, but I can't see why it seems to produce the same knock at high RPMs under NO load.
View 4 Replies
I have a 1994 ford ranger 4 cylinder manuel transmission regular cab. I am hearing a grinding noise when I push and hold my clutch down. It doesn't make any noise when my foot is off the clutch. It makes the noise off and on when i stop at a light or stop signs. I have also noticed a vibration at certain speeds around 30 and then again around 70. What is the cause of these noises? Could it be my U joint?
View 5 Replies
2004 auto ranger 120k miles
When I bought it there was a lifter making a tap tap tap. Its not all the time or consistent which makes me feel its a failed lifter as opposed to a rocker arm that is loose. Ive tried the "stuff" in the oil. Seafoam, marvel mystery, etc with no luck. So this coming winter Im going to break it down and replace the lifter.
First question. I havent put a stethoscope on it or used the "hose to ear" method to track down which one it is. Im pretty sure its the right bank in the front. Will it be obvious which one it is when I get it broken down?
Next. At 120k miles should I be worried about the other lifters? Ive never had one fail on anything I own and hardly ever hear them on other cars. I pretty much thought that hydraulic lifters were failproof anymore. Should I be worried about the others?
Next next, do I need to be worried about damage to the pushrod and or rocker arm? Should I be prepared to replace those as well? Finally anything else to be concerned about or consider?
View 7 Replies
I was pulling out of a parking lot making a sharp turn when all the sudden I lost my power steering. I have a '94 Ford Ranger manual transmission. It didn't make any sounds. I was going to try to keep adding power steering fluid to it and try to get it home to my mechanic in my hometown - but it drips constant liquid when I drive it down the street (you can see drips) so I don't think that's possible. I've read a lot on here about gear boxes failing, but would this cause it to leak even if the truck wasn't running? (the puddle builds quickly when its just sitting there, engine off). I took it to a mechanic (I don't have tools), and they said they can't say anything for sure until they look around, it could be seals or a new gear box.
View 2 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
I had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 Replies
