Ford Ranger / B-Series :: 1993 - Won't Go Past 35 MPH And Shakes?
Jan 23, 2017
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 Replies
Jan 23, 2017
Advertisement
Ford Ranger / B-Series :: 1993 - Shakes Really Bad And Lost Power After Replacement Of Brake Caliper?
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 RepliesFord Ranger / B-Series :: 2004 - When Sitting In Park Will Not Rev Up Past 3500 RPM
My 04 EDGE 3.0 when sitting in Park will not rev up past 3500 RPM. The check engine light has been on for awhile showing P0316 and I believe P0302. My mechanic said number 2 is misfiring; the coil packs/wires/injectors are all good. He said eventually if I want to keep it a new engine would be needed, but as long as it's not burning oil it should be okay to drive for awhile. Why it won't rev up? I wouldn't think one cylinder misfiring would cause that.
View 3 RepliesFord Ranger / B-Series :: 1998 - Shakes On Startup?
I have a 98 Ranger SuperCab XLT 4WD 4.0 Auto. Occasionally, especially when it has been sitting for more than 3 days, it shakes for maybe 30 seconds on startup. It smooths out gradually after that, maybe 15 sec. to normal smoothness. It seems like it is firing on all cylinders and is more like something out of balance.
Never does it when sits less than 2 days. When it happens, the longer it sits the worse it shakes.
Ford Ranger / B-Series :: 2002 - Trans Hesitates - Shakes At 65 - 70 MPH?
02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.
tranny fluid/ filter just replaced with no change. new plugs and wires
Ford Ranger / B-Series :: 1999 - Shakes When Idling And Driving
My 1999 ford ranger, when started, shakes and then while i am driving. my check engine light is on and reads a #3 cylinder misfire. I have taken it somewhere to get it checked out and they can't figure out what is wrong with it. this problem only happens 50% of the time. I don't know what to do. Also just got a tune up.
View 14 RepliesFord Ranger / B-Series :: 1993 - Cat For PA State Emission?
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 RepliesFord Ranger / B-Series :: 1993 2.3L 5 Speed Won't Go Into Gear
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 RepliesFord Ranger / B-Series :: 1996 XLT - Rear End Shakes When Driving Down The Road
My problem is wih my 1996 Ford Ranger XLT 6Cyl. 4.0L 2WD Recntly it started shaking violently in the rear as I drive down the road any road. Mainly slow to about 50MPH or slower, it just starts to shake really hard and then it stops then out of the blue it will do it again I thought it might be the back Drums maybe the shoes came apart and were catching but they are fine everything looks fine, could it be the gearbox on the axle? I don't know...
View 5 RepliesFord Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
Ford Ranger / B-Series :: 1993 - Wiper Motor Removal?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesFord Ranger / B-Series :: 1993 - Front Sway Bar End Links?
I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesFord Ranger / B-Series :: 1993 - How To Replace Key Lock Cylinder
I am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
Ford Ranger / B-Series :: 1993 - Modulator Valve Location?
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 RepliesFord Ranger / B-Series :: 1993 - Location Of The Fill Plug?
Where is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
Ford Ranger / B-Series :: 1995 - Periodic Rough Idle When Warm / Shakes And Misses
My 95 4.0 has had a periodic idle issue for quite a while. It seems it may be getting worse. Here is when it may only happen:
Vehicle is fully warm. I shut it off for about 1 hr or so and when I restart it, it shakes and misses in idle. It will idle fine after I drive it around or if I rev the engine for a while when still parked.
This never triggers the "check engine light". New fuel filter, plugs and wires.
Ford Ranger / B-Series :: 1993 - 4x4 Not Engaging / Grind Just For A Quick Sec When Shifting
So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?
Ford Ranger / B-Series :: Door Swap From 1992 To 1993 Model
Will a driver door from a 92 ford ranger fit a 93 ford ranger?
View 5 RepliesFord Ranger / B-Series :: 1993 - Cruise Will Not Disengage With Brake Pedal
1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
Ford Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesFord Ranger / B-Series :: 1993 - Clutch Release Bearing Install
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.