Ford Ranger / B-Series :: 1993 - Wiper Motor Removal?


Apr 12, 2015

How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?

View 3 Replies

Advertisement

Ford Ranger / B-Series :: 1997 - Blend Door Motor Removal?

My actuator/motor doesn't have the screws that hold it on. It's just clipped down. Can I just pry it up & off with out it breaking the clips that hold it down? It's a 97 Ranger.

View 2 Replies

Ford Ranger / B-Series :: 1987 - Location Of Interval Wiper Governor?

I have a 1987 Ford Ranger that only has high speed on the wipers. According to the Ford Shop Manual the probable cause is the interval windshield wiper governor, which is suppose to be mounted above the driver's side kick panel. The manual even shows a drawing of the governor and the location. Nothing is there in my truck. Where it is located and what it looks like?

View 14 Replies

Ford Ranger / B-Series :: 1988 XLT - Windshield Wiper / No Clicking From Relays

I have a 1988 Ranger with the 2.9. 2wd, xlt. It seems that my wipers have no power. I put a test light in the fuse panel where the 6A cb is and no light. To verify I wasn't doing something wrong, I put it in the dome light and tester came on. I tried with the wiper switch on interval, low & hi. I can't seem to find where the power comes from to follow back from the fuse panel. The washer fluid doesn't work either. No clicking from relays or anything.

View 2 Replies

Ford Ranger / B-Series :: 1993 - Cat For PA State Emission?

I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!

View 3 Replies

Ford Ranger / B-Series :: 1993 - Won't Go Past 35 MPH And Shakes?

Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...

View 6 Replies

Ford Ranger / B-Series :: 1993 2.3L 5 Speed Won't Go Into Gear

Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....

View 3 Replies

Ford Ranger / B-Series :: Top 2 Bolts Removal Of Transmission?

How in the heck do you get the top 2 bolts off of the transmission housing? They seem to be positioned in such a way that they are impossible to remove.

View 14 Replies

Ford Ranger / B-Series :: Wiper Control Lost All Function Save For Fastest Setting

My Ranger 2004 Edge wiper control lost all function save for the fastest setting. The day before I lost the lower settings but then they were there as usual. This also happened once before about a month ago and then it came back. Last night no such luck. Everything else seems to function fine. Where to begin?

View 10 Replies

Ford Ranger / B-Series :: 1989 - Side Wiper Quit Working - Shaft Location?

This morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.

View 14 Replies

Ford Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly

I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.

So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?

View 8 Replies

Ford Ranger / B-Series :: 1993 - Front Sway Bar End Links?

I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.

View 4 Replies

Ford Ranger / B-Series :: 1993 - How To Replace Key Lock Cylinder

I am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.

I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.

There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.

View 4 Replies

Ford Ranger / B-Series :: 1993 - Modulator Valve Location?

Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.

View 7 Replies

Ford Ranger / B-Series :: 1993 - Location Of The Fill Plug?

Where is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?

Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?

View 2 Replies

Ford Ranger / B-Series :: Fuel Filter Removal / Replacement

I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?

View 7 Replies

Ford Ranger / B-Series :: 2000 - Harmonic Balancer Removal?

I have a 2000 2.5 and need to remove the harmonic balancer. Are the threads righty tighty or lefty loosey.I'm replacing the timing belt and pulley

View 1 Replies

Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?

I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.

View 1 Replies

Ford Ranger / B-Series :: 1988 - Wiper Won't Roll Down To Normal Position And Not Working At Slow Setting?

1988 Bronco II 2.9L Issues:
- When I turn off the wiper switch the wipers immediately stop in place, they do not continue to their normal 'down' position.
- The switch's adjuster to slow the wipers isn't working, only the low and high settings work.

What I've done so far:
- Replaced wiper switch with used from spare parts.
- Replaced wiper switch with new from spare parts.
- Replaced wiper motor with remanufactured from Autozone.
- Thoroughly cleaned wiper motor ground terminals.
- Replaced interval wiper governor with used from spare parts.

The problem occurred after the truck sat in my garage for 6 months while I removed and reinstalled the engine to replace some gaskets & seals.

View 6 Replies

Ford Ranger / B-Series :: 1993 - 4x4 Not Engaging / Grind Just For A Quick Sec When Shifting

So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...

issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?

issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?

issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?

View 14 Replies

Ford Ranger / B-Series :: Door Swap From 1992 To 1993 Model

Will a driver door from a 92 ford ranger fit a 93 ford ranger?

View 5 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved