Recently my 93 Ranger 4.0 has started to take longer to shift into 2nd gear and the rpms are way up there. shortened 2nd gear then 3rd will be fine and so on. This only happens after the engine goes completely cold. I took it to a transmission shop and they said tranny is fine...Other than this issue the truck is fine.
View 6 RepliesI have a 2002 Ranger with a 2.3 lt engine and a 5R44E Transmission. Has 120,oookms (75,000 miles) I have an issue.
Here is what was happening: Would not shift into Drive...took a long time to do so.... and had a 2 to 3 gear flare.
Here is what I did: Replaced the valve body gaskets. Improved a lot. The 2 to 3 shift flare has gone. The delayed shift into D is mostly gone BUT still takes 15 to 20 seconds to shift into D. Once in gear no problems shifting. Does not slip and NO OD light flashing.
What do I need to do to fix the delayed shift issue.
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesNot only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 Repliesive been experiancing an issue with my trucks shifting. it shifts smoothly but doesnt like shift into 5th, as im driving it stays in 4th longer than necessary. my thought was that it was tied to a shift sensor, what do you think?
View 5 RepliesEither one of my power steering hoses or the gear box is leaking on my 93 Ranger. It appeared the return hose was leaking where the rubber meets the crimp. So I decided I would go ahead and change the return and pressure hose to see if it stops the leak. It was a disaster. It's 2.3L manual transmission 4x2. I got the return hose off ok. I put the wrong size wrench on the pressure hose fitting at the pump but thought it was loosening but it was rounding the nut off. So I couldn't even change that hose. I installed the new return hose and retightened the pressure hose at the gear box.
Well it was a pain getting the flare fittings of the hoses into the steering box so I could tightened the flare nut down. I finally got them tightened, I think, but then when I started the engine fluid shot out of there like a water hose. It's coming from the fittings at the gear box that I thought were tightened. I reloosened and retightened them again and still it's shooting out everywhere. There is so little room getting a wrench on the hose fittings, it was slow going. What do you need to remove in order to get a good straight shot and installing these flare nut fittings and tightening them down right? If I remove the pump will it be easier to install the hoses on the gear box? I have to remove the pump now to change the pressure hose.
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
It's a 4 cylinder 5 speed, and once or twice a day when the light turns green and I go to put it in low gear, it just doesn't want to go into gear easy. It's like the syncro isn't happy or something. The clutch is depressed all the way and not dragging.
View 14 Replies2003 3.0 FFV 5 speed automatic...... Just noticed recently that it seems slow to go into 2nd gear.....the rest of the shifts seem fine, firm and unchanged.....
View 4 RepliesI have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 Replies98 Ranger 4x4 4.0 L Supercab. Today I replaced my instrument cluster lights. When I put everything back together i noticed my gear shift indicator is off and I cant shift into 1st or 2nd. What did I screw up?
View 5 RepliesI am looking over a 1998 Ford Ranger. Very low miles for its age (67,000) and kept in very good shape. When I took it for a drive, I noted an issue.
- there's a whining sound in first gear and reverse that varies according to the engine RPMs. I thought it might be the power steering pump, as that whined when I turned the wheel.
However, the noise went away when I shifted to the higher gears. Been a while since I drove a stick - my Bug back in 2003, IIRC.
What I might be getting into? I really like this machine, aside from that issue, and I would like to nail the problem down ASAP...
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 Replies02 Ranger 2.3 4cyl 5 spd 115K.... My A/C seems to take longer and longer to start cooling/ When it does start cooling it seems that is is actually colder than it has ever been (original owner) and the control is more sensitive to the touch when moved. Being a 4 cyl it's easy to detect when the compressor kicks in and it seems each time it is taking longer to do so. If I stop the motor, it goes thru the same cycle of time or longer before cooling (compressor kicking in) again. No codes, No unusual noises.
View 5 RepliesWonder if its dry driveshaft slip splines? Only happens when leaving a dead stop under hard acceleration. Hard to describe sound, but seems to be coming from behind me, almost sounds like 2 broken pieces of steel snapping past each other. frame is o.k., leaf springs are o.k. , doesn't do it when shifting between gears or if I gently take off from a stop. I don't think there's a grease fitting for the driveshaft where the splines are (where the 2 piece shaft takes up slack for being loaded or unloaded) may have to take that apart once the weather breaks and see what i find. my 1st ranger never had this issue after 200K miles. this truck is now at 145K but its almost 20 years old. I've read somewhere before about pulling the shaft apart & greasing the splines up. does this sound like a possibility for whats happening? not sure what else it could be.
View 3 RepliesI have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
I have a 85 bronco 2, but i have no luck with responses in Bronco 2 forum, so here goes. It is the 2.8 carb, manual trans with 109K miles. Idles really well some hesitation when taking off but really bad miss and not power under acceleration. KOEO codes are 31 and 84 CM code 18. I have plugged the vacuum line to the EGR and have noticed a dramatic difference. I have tried to rev the engine and check the vac line to the EGR but I do not feel any vacuum, and at idle the vac line on or off doesn't change things. Any recommendations to whether it is the Sensor or the valve itself and what gives with the 18 code. I am hoping to have timing checked by the weekend.
View 2 Replies2007 Ranger 4.0.... Initial start of the day it cranks a bit longer than it should. After warm, it starts fine.
View 1 RepliesI have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 RepliesToday on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 Replies