Ford Ranger / B-Series :: 1993 - Clutch Release Bearing Install
Jun 12, 2012
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
View 7 Replies
Advertisement
My battery went flat and to compound my misery, when I went to open the hood, the cable was snapped. How I can open the hood without using the release cable ? I'd rather not have to pay for it to be taken to the mechanic and then also pay to have the battery changed !
View 3 Replies
My tires are 245/75/16, is there any benefit in installing smaller 16" tires?, I'm 5'5", I can still get in, but I would like to have it a little bit lower, will that affect mileage, speed etc.? would that even make a difference? if it possible how small can I go without affecting performance?
View 13 Replies
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.
View 4 Replies
So my ranger was having a textbook wheel-bearing noise at around 50mph....when I turned to the right the noise went away implicating a passenger side wheel bearing.
So I replaced both of the hub bearings on the pass side and noticed that the front axle shaft u-joint right behind the spindle was really bad and was going to change it but couldn't get the spindle off so I said screw it.
Took it for a drive and the noise is still there. Could a worn u-joint possible replicate a wheel bearing noise? I am used to them making a clicking/popping noise while turning when they're bad, but not a whirring sound.
1993 ranger 4x4 manual locking hubs.
View 4 Replies
I just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
View 3 Replies
I was messing with the battery in my 200 Ford Ranger the other day and must of arc something. I know this because after plugging my battery back up my radio fuse was blown and my alternator was killed. I replaces the radio fuse, that works now, and got a new remanufacted alternator (tested mine at Advance it was dead). I installed it and nothing changed. The battery still wasn't charging. I know the battery is good because I tested it at Advance Auto. I took the alternator back and the shop replaced it with another remanufacted one. Same thing, installed it and the battery doesn't charge.
This time I took the alt back off and had it tested at Advance. The alt was dead. So I don't know if the part store gave me TWO bad alternators or if my truck is killing them. I find it hard to believe it could kill them immediately but my automotive knowledge is not that vast. I took the second (third counting my original) dead alternator back and they gave me a brand new one no extra charge. So I don't want to put a brand new alt in my truck and it kill this one too because I doubt they will give me a fourth one. What is going on? Could it just be as simple as I got two bad eggs?
View 9 Replies
I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
View 7 Replies
I have an 01 Ranger 4x4 that recently started to make a loud speed dependent noise from the drivers side front wheel, a quick jab to the right on the steering wheel and it stops, straiten out and it comes back...since I know my shocks are worn and have some cupping on the front tires my first thought was tire noise so I moved the back tire which is evenly worn to the front and no change, next I removed the tire and checked everything visually.
All seems ok, the brake does not seem to be dragging and there is no evidence of a cv problem, everything seems tight, so I'm guessing the problem is a bad wheel bearing? If I grab the tire at 12 and 6 there seems to be excessive movement from top to bottom, there should be none right? If memory serves any movement is indicative of bad wheel bearings? I guess I'm looking for some vindication before getting a new hub?
View 14 Replies
My 96 ranger with a 5 spd manual and two piece drive line has the center carrier bearing going out (squeals,vibrates,etc.) I got the part no. from the dealer but they are obsolete. is there a one piece drive line i could put in and what would that take to do.i remember a thread on it somewhere but cannot find it in the search. i would prefer not to use aftermarket because they only have a one year warranty.
View 10 Replies
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 Replies
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 Replies
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 Replies
The T/O bearing makes a high pitch squeal until you put light pressure on clutch then it will go away. Does this thing have a preload on bearing at all times or should there be free play like in the old days??
Another thing that has me wondering is when I push clutch all the way in it actually puts a load on the engine. Having T/O bearing so bad it puts a load on the engine?
View 2 Replies
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 Replies
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
View 8 Replies
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 Replies
I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 Replies
I am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
View 4 Replies
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 Replies
Where is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
View 2 Replies
