Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 RepliesRecently my 93 Ranger 4.0 has started to take longer to shift into 2nd gear and the rpms are way up there. shortened 2nd gear then 3rd will be fine and so on. This only happens after the engine goes completely cold. I took it to a transmission shop and they said tranny is fine...Other than this issue the truck is fine.
View 6 RepliesEither one of my power steering hoses or the gear box is leaking on my 93 Ranger. It appeared the return hose was leaking where the rubber meets the crimp. So I decided I would go ahead and change the return and pressure hose to see if it stops the leak. It was a disaster. It's 2.3L manual transmission 4x2. I got the return hose off ok. I put the wrong size wrench on the pressure hose fitting at the pump but thought it was loosening but it was rounding the nut off. So I couldn't even change that hose. I installed the new return hose and retightened the pressure hose at the gear box.
Well it was a pain getting the flare fittings of the hoses into the steering box so I could tightened the flare nut down. I finally got them tightened, I think, but then when I started the engine fluid shot out of there like a water hose. It's coming from the fittings at the gear box that I thought were tightened. I reloosened and retightened them again and still it's shooting out everywhere. There is so little room getting a wrench on the hose fittings, it was slow going. What do you need to remove in order to get a good straight shot and installing these flare nut fittings and tightening them down right? If I remove the pump will it be easier to install the hoses on the gear box? I have to remove the pump now to change the pressure hose.
I have a 98 ford ranger with a 3.0 v6 it has 228,000miles standard tranny but I keep the truck running great. I did the plugs and wires about two weeks ago and it was running fine, actually great. This morning I got into the truck to start it this morning and it barely started. It fired up but barely stayed idling. I would get into the petal and it wouldn't raise rpms. I had to get to school so I headed out. I couldn't get any speed in gear the truck wouldn't gain speed. It would sputter and pop and then all of a sudden it would go ok but then start popping again. I took it to a buddy shop and his scanner showed p1131 and p1151 both codes. I don't know what to do?
View 13 RepliesI am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 RepliesToday on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 RepliesI have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesI'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesI am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 RepliesWhere is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?
Will a driver door from a 92 ford ranger fit a 93 ford ranger?
View 5 Replies1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 Replies93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
1993 3.0 V6 5 Spd ... Changed plugs wires Cap and rotor put in a new idle control Valve. No Check engine light. When i am running down the road feels like it surges,hickups, while its at idle the motor shakes like no tomorrow. Just dont want to throw money at something and not be the part that was wrong. Truck has plenty of pickup runs like a raped ape going down the highway. seems when i accelerate the miss clears up and not there. RPM gauge needle has some movement in it. Also put in K&N filter fuel filter as well.
View 6 RepliesI have a 1993 ranger 3.0L/6cyl/automatic/ a4ld. I replaced the transmission and torque converter with one from a salvage yard that has approx. 76k miles. I added tranny fluid and idled the engine for approx. 10 minutes in neutral, but the fluid has not begone to circulate. I pulled off the trans line at the radiator and there is no flow with the engine running in park. Where should I start with the diagnostics for this problem?
View 4 RepliesTruck is a 1993 ranger 4.0 ohv
Ok I have been getting 157, 158, and 159 codes. I have cleaned and replaced the MAF with no success. I checked the voltage to the sensor 12v, checked the voltage from the signal wire and it is to high. It has been high on the cleaned unit and on both replacements, so I am thinking it is not the MAF, but what will cause it to register high. I cant get the signal voltage below 1.9V at idle.
Signal also reads high with the ignition on and the engine off. What would cause the voltage to be high, I have read it could be an IAC but I would think that would not effect it with the engine off.
I have a problem with the serpentine belt tensioner, on a 1993 Splash; 4cyl motor. The tensioner spring is frozen/stuck, so it is set to where it is. Tried to 'exercise' to free it up, that did not work, and sorta' rounded out the 3/8 square hole doing that. So, ordered an new tensioner assembly. I felt around the tensioner mount at bottom, do not feel a bolt head. So it must be flat head allen or torx bolt, correct ?
View 9 Replies