Ford Ranger / B-Series :: 1992 - Won't Downshift At 45 To 50 - Transmission Modulator Valve?
Jan 26, 2015
So my 92 4.0 automatic has always been kind of a slug since we've bought it with 101,000 miles on it. It's been tuned properly and fuel pump, filter, and regulator been replaced. It runs pretty good but when you're going highway speed or even like 45-50 and stomp the gas it doesn't feel as if it's downshifting. The transmission looks like it may have been replaced or maintained, it shifts good, pulls good. Fluid is clear and clean, no leaks, no burning. I see that it has a vacuum modulator valve but don't know where it hooks up to. I can barely see it behind my catalytic converter. It will have to be removed to change it for sure. But I'm trying to see where the vacuum line goes from that modulator valve. I see the valve but I didn't really notice a vacuum hose coming off of it but again my view was obstructed by the catalytic converter. Would it cause hesitation problems if it was bad or not even hooked up?
View 1 Replies
Advertisement
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 Replies
My 93' Ranger XLT extra cab 2wd, 4.0 engine and A4LD auto tranny with 126,600 miles has a rough downshift into 2nd gear about 15 or 16 mph. Down shift to 1st is real smooth and upshifting thru the gears is smooth. I just put a new modulator valve on it and upshifts smooth out, they were getting to be hard shifts before changing that valve. I do not know if there is any adjustment that can be made to smooth out the rough downshift when slowing down to a stop for red light. The U-joins are in good shape and new carrier bearing assembly on driveshaft and no extra play in the rear end. A band adjustment maybe or just have to live with it.
View 5 Replies
1996' Ranger with 183,000 miles. 2.3 cyl., Automatic, XLT
When I am driving and get to the 35 to 60 mph range, my trucks transmission wants to upshift, then immediately downshift to the gear it just left. It goes back and forth like this till I get where I am going, or after about 10 miles it will stop doing it. I checked the transmission fluid, and it is full and still pink.
I took it to Advanced Auto, and it blew a code of ECL Bank 1 I believe. I looked around the 'net and I think it came out to be the front O2 sensor may be bad/going bad.
Last week while it was warm enough I was driving with the rear window open, and noticed the faint smell of Rotten Eggs (this has been the only time though). Today I drove about 50 miles and basically used a quarter of a tank of gas. I am wondering if the catalytic convertor may also be going bad?
View 9 Replies
I searched a lot but did not find these symptoms on my 1992 Aerostar 3.0 2WD with A4LD transmission.
In overdrive, accelerate to down shift, and the transmission goes out of gear. Engine revs as if it was taken out of gear. Manually shift to Drive, and it works fine.
Overdrive works fine if at speed, and works to shift up, but if going slow enough to drop to lower gear, transmission goes out of gear. Manually in drive, works fine.
I may have other symptoms, but this was on the way home from work, and I just parked it. I checked fluid level, and it was fine, still in the cross-hatch area of the stick, light colored oil, no smell.
I will replace the modulator and replace the filter, and see what that will do. If the overdrive works at overdrive speed, I do not see how that could be an overdrive housing failure that I have seen in many posts. I am aware of keeping track of the pin for the modulator.
I also have read that band adjustment is not a good idea. If they are worn that bad, they should be replaced. I don't think it is a band or clutch problem. I think it is a shift control problem. We will start with the modulator and filter and take it from there.
View 4 Replies
I have a 99 Ranger, 3.0 xlt 2WD Automatic 5r55e(???) tranny (i know its the 5). I have the o/d off light flashing. It comes on when fluid gets to op temp. When on it shifts hard into 2nd and hard when it downshifts. No slipping. I have had the truck in the tranny shop for 3 weeks, owner said he re built valve body gasket (didnt work) tried 3 diff used tranny's (didn't work) or so he says. He said it needs to be rebuilt.
I have searched up and down for what it could be, there is so much out there, it only confused me more. If i have to rebuild i will, i think the tranny shop was pulling my leg (for more reasons than mentioned). I have a check engine light on nothing to do with tranny...there is a tranny code, he would not tell me but i will have it checked. Been told could be throttle position sensorl, speed sensor cracked case and a million other things. I have some mechanical abilities, (not too much w/ tranny's) but i can change a few simple sensors.
View 1 Replies
I bought the 94 B2300 from a guy that said he got it from an auction and didn't know much bout it. Got 30 mins down the road and went to down shift to 4th coming into town and all I got was grinding. Turned it off and it would go into other gears and start in gear with the clutch pushed in. Wen I tried to take off it wouldn't move and just died. Towed it home and installed a new clutch kit in it. Got the clutch bled and went to test drive it and now it is stuck in 1st gear. Can it be easily fixed or am I going to have to replace the transmission...
View 3 Replies
I have posted on here before about this very issue, thinking it was primarily the transmission. In additon to a hard upshift/downshift (it almost feels like getting a little "kick" from behind while in the truck) I was getting a flashing O/d light, etc.
Since then the tranny died. No shifting at all. I was able to find a usable replacement from another truck (the guy sideswipped a pole, and decided he was done with it, as he tweaked the front frame slightly), which was working fine (before the accident).
I swapped the units out (trans and T/C), and the truck has life again! No flashing O/D light, nice power, and good gas mileage (I went from pre-failure 15mpg to 20mpg now).
However, the kick has never gone away.
So, what next? How much "play" should there be in the driveshaft when the vehicle is parked? I can move it a little bit. Should I consider servicing/replacing the U-joints? Or should I now suspect the rear diff to be the culprit, and how can I best determine this?
Also, can you switch out one rear end for another? If you can, is there any any paricular one that is better to use for towing/hauling as opposed to, let's say, off-roading or city driving?
As for the vehicle in question, it's a 1995 Ranger XLT extended cab with a 3.0V6 and auto trans. I believe it's supposed to have a limited-slip diff, but how do I determine this?
View 14 Replies
My compressor on my 92 Ranger did not have any clutches on it. Where they went. I got a compressor off of a 94 at the pick and pull. It was charged and the compressor turned fine. Brought it home and tried to install it. My hoses in the back of mine(92) are different than the 94. I went back and got the hoses, condenser and evaporator off of the 94. Put it all together. The high pressure hose on the 94 has some sort of switch on the high pressure side. What is this switch for and how can I wire it in to the electrical system on the 92? I assume it is some sort of pressure switch that allows the system to flow. I'm getting 30 pounds on the low side and 150-200 ponds on the high side. Also, when I increase the RPM's, the compressor kicks on and off. It's not like it would or should normally but fast.
View 7 Replies
I have a 92 ford ranger. About a year ago it shut down on me as I was pulling out of a parking lot. I replaced the Cam sensor which IS NOT located on the engine block by the fire wall. It is located on the front of the engine just above the primary cam which is just above the crank shaft and its sensor. It fired right up.
Then the oil pump went out and I just replaced it the other day and the pressure gauge/needle went past the half way mark even at idle. I drove around a bit, maybe 10 miles, then got in it to go to the gas station and got about 50ft from the house and it just died again and will not crank back up.
I am thinking its that darn cam sensor again. But, just like the oil pump was, it's a pain to get to and replace. How to test it. Oh, it is a 2.3 4 cyl. double overhead cam. I do have fuel pressure, I checked that already.
View 14 Replies
I am the owner of a 1992 ford ranger 4.0 that refuses to start. She turns over, but theres no pressure coming out of the fuel rack/valve. Might be the fuel pump but it started with a little boost about a month ago and now nothing. Head gasket and transmission have been tuned up as well! I've also checked the power distribution box, and spark plugs both seem to be doing thier job! What am i missing?!
View 2 Replies
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 Replies
Ok I got the brake pull fixed (I think) on my 92 Ranger 4x2 4.0 extended cab. I still will have to change the driver's side brake hose for prevention and the driver's side caliper just so everything will be new. But it stops straight now with a new brake job, pass caliper and hose on. However, this other problem has been ongoing and it does it on my 1998 Ranger too. It's not the heater core.
I think the evaporator case is filling with water and dripping down under the carpet. So the drain tube must be stopped or the case must have a bunch of leaves stopping it up. But where is this tube you're suppose to check? I don't see a conventional drain tube I only see a blower motor vent tube that doesn't drain to the outside of the car anywhere. I know my 73 Charger has a rubber drain tube that comes out of the evaporator case and drains onto the ground. But where is this one on a Ranger or what else could it be? It's only the passenger side so it's got to be that.
View 2 Replies
My Ranger was running great when suddenly on the highway it just died. I towed it to local nationally known brake/ muffler shop where a good friend is the manager. He narrowed it down (guessed in my opinion) to no spark and no fuel. He thinks it could be the crank sensor, the fuel pump or the ignition module. Is there any way to pinpoint the problem without replacing parts? It will sometimes start and run for about 2 seconds before shutting off. It will not repeat this unless it sits for a day or two. I am not sure if there are different 2.3 engines available but mine is fuel injection and has two sets of spark plugs and wires.
View 9 Replies
'92 Ranger 2WD with 4 cyl and 9" brakes, right rear wheel cylinder keeps blowing out, replaced it twice. I've thought about maybe an obstruction in the left brake line creating too much pressure, or in the junction block on the rear axle. I believe only one line leads to there from the master cylinder, so what else could it be? Only other thing I can think of is that the right brake has a mechanical problem which is causing the forward shoe to move too far away from the cylinder, leaving no 'stop' so the piston just slides right out of the cylinder. But I can't figure that. Original adjuster star wheel was chewed up so I swapped in another, doubt it's that.
View 14 Replies
I recently got a ranger from my buddy and it keeps blowing the EEC fuse in the engine compartment. We have replaced the EEC relay and the EEC power relay. As soon as you turn the key it is blowing the fuse.
View 1 Replies
I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
View 3 Replies
I'm working on a 1992 ranger with the 2.3l. Hard start almost every time, sometimes have to hold throttle open sometimes not. Won't start at all this morning. When it does finally start it takes a while for it to start firing on the intake side plugs. Haven't had time to check fuel pressure yet but can hear pump cycle when key is switched on.
View 8 Replies
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
View 1 Replies
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 Replies
All I did was take wheel off to tap a stud and I saw the inboard pad shim came off. So I removed the shim and reinstalled everything and the wheel is severely pulling to the right. Yesterday I took the caliper off but did not take off hose, cleaned slide pins and lubricated with anti seize. Still pulling to right bad. Don't hear any squealing or grinding. But pass side wheel is definitely hotter than drivers side. One mechanic said he thinks it would be a bad hose before replacing caliper. What could it be?
View 8 Replies
