Ford Ranger / B-Series :: 1991 4WD Manual Tranny Locks Up After Going Forward A Few Feet
Jun 5, 2013
My 4x4 4WD Ranger has a 5 speed manual tranny that locks up after going forward a few feet. It can back up all day long but locks up going forward. some god awful noises (grinding, clunking, etc) come out of that gearbox. the 4wd is electrically operated. the ? is , can this tranny be rebuilt with a kit? I'm having great difficulty finding a replacement. Are bronco II's compatible? Engine is 2.9L V6. On disassembly I found 2 meshing gears with broken teeth.
View 5 Replies
Advertisement
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
View 5 Replies
I am working with a friend on his 99 Ranger with a 4.0 . When first started it will idle rough and hesitate for the first 300 feet or so, and then clear up and run smooth the rest of the day. If he lets it set for 6 or more hours it will repeat the problem. He has taken it to a local Ford dealer and they have replaced spark plugs, plug wires, coil pack, cleaned the throttle body, checked the air idle motor and passage.
He has had it to the dealer 3 times and their latest plan is to pull the heads @ a cost of 1500.00 to start. Since it runs well, no coolant in oil or oil in coolant nor loss of either fluid, I couldn't figure why they want to pull the heads.
To date it has not thrown a code, I ran it on a New Generation Star tester and cannot find a code. The truck runs great after the first intial start up and does not give any signs of cutting out or lack of power. My guess is it is losing fuel pressure overnight and is taking a while to reprime. Original fuel pump and 160K miles. Will do a fuel pressure test this weekend.
View 1 Replies
My 1988 Ranger has started leaking a gush of water onto the feet of passengers the first time I accelerate after a heavy rain. I saw the water flowing out from behind the glove box area as I started driving forward. How to fix this leak?
View 5 Replies
This is my first experience with auto tranny trouble so I'm a bit out of my depth. It started a few days ago. When you put it in gear and step on the gas, the engine revs, but no forward movement. If you keep giving it gas and rev it up, it will eventually grab and off you go. This happened around town after I took it to work last week when I went out for lunch.
When I drove it home, it slipped in and out several times in town, then by the time I got out of town (maybe 5 minutes driving) it evened out and didn't slip the rest of the way home (a 45 min drive). My assumption is that once it warmed up a bit that stopped the slipping. I checked the transmission fluid when I got back from lunch, and it was a little high. I drove it again today a week later and same thing only I didn't drive it long enough for it to warm up and stop slipping like it did the other day.
Other details: The truck is a 4x4, extended cab, v6 Ford Ranger with about 175k miles on it. I've had it about 1 1/2 years and its performed great up till now.
View 5 Replies
My 1986 528e was used to jump start another vehicle, ran it for a minute or so in Park @ 2000 rpm per owner's manual instruction, got other vehicle started, reversed away from other vehicle, put selector into Drive and car would not move forward. Tried all other forward options, no go. Reverse works just fine. Checked fluid and it was low. Topped it up but still no forward gears. Had vehicle towed home. Checked selector cable and it is OK. What could this be to go out all of a sudden like this?
View 4 Replies
Looking at buying a new truck. We'll in a crunch actually due to my tranny going out this morning. One that I'm looking at looks great, except the obd2 port is dead. Where do I start looking? What fuse etc. It appears auto correct changed the obd2 to body and I didn't catch it...
View 8 Replies
I am installing a used tranny in the ranger. According to the salvage yard the tranny fluid and filter was removed and fluid drained from the torque converter. How am I supposed to fill the torque converter?
View 1 Replies
. I'm going to FINALLY change the tranny fluid in my 95 Ranger Splash this weekend and need all the feedback I can get! It's a manual trans with miles shy of the 250,000 mark...still on the original stuff!! I'm only the 2nd owner but I bought the truck with just 45,000 miles on her so I'm willing to bet the farm that it's never been changed. It's getting harder to shift from 1st to 2nd and I'm getting a little bit of grinding from 3rd to 4th if I shift too fast. Reading all the threads everywhere online, so many different people have so many different theories from stock Mercon V to MOTOR OIL??? The motor oil thing floored me but I understand the viscosity difference between hydraulic fluid and lubricating oil. figure out what the best thing to replace the original with to prolong the life of this long running wonder vehicle!
View 5 Replies
My 1991 ranger with a 4.0 turns over but will not start. It acted like it ran out of gas put again seems to do ok then it did same thing it sat over night then would not start so I thought I would put some gas in the intake so it starts ran real rough but smoothed after a few minutes ran fine after that next morning same thing no start did same put gas in intake at first no start just turned over didn't even try let it sit for awhile then tried again it fires up ran rough but ran now I get nothing just turns over pulled codes 22and 122 replaced both had ignition mod checked its good new coil pack no change so at this point i hear fuel pump kick on fuel getting to fuel bar but seems a bit week on pressure going to get pressure gauge and see what it says but in the meantime I am loosing my mind...
View 9 Replies
I recently bought a 91 Ranger 4wd for my son. The guy I bought it from put new manual lock outs on it. every time I take the tire off on either side the hub comes with it! Is there a clip or retainer missing? If so what and where can I get one?
View 4 Replies
My dad's 1991 Ford ranger 3.0 2wd just died on him when he was driving home and I checked to see if the truck had a spark and it did not so I replaced the ignition control module, then ignition coil, then distributor and rotor cap(plug) and I put new plugs and wires on it a few months back too. I also checked to make sure that the timing chain was working as well (while I had the distributor cap off). Then I realized that the EEC maxi fuse was blown. I then found a fourm that said it might be the relay so I replaced the EEC and the fuel pump relays while I had them both out. Every time I put a new 30 amp fuse in the EEC slot and turn the key to start it the fuse blows and the truck won't start. What might be wrong?
View 1 Replies
Will move if n 4low and give some rpm's. Reverse is fine, disassembled and clutches look fine.
View 1 Replies
2003 ranger 4.0 5 speed .... Pretty new to the car/truck world only 18 and this is my first truck, I traded my focus for it and so far so good. Its my first manual but i got to tinkering and i noticed some oil build up under the front end so i got to looking and found this, wondering if its an issue, should I try to fix whatever is causing it or take it to a mechanic. Looks like between tranny and engine to me.
View 2 Replies
Last week I noticed a slight "whomping" noise in my 2010 Ranger. Not a knock, not a ping, nothing that sounds metallic. Just a rhythmic whomping sound that only shows after the engine and tranny are hot.
It only does it in Drive or Reverse; and not in Park or Neutral. The tech at the dealership (30k on the vehicle) says he thinks it is a bearing in the torque converter.
View 7 Replies
Getting the Banana ready for it's smog test appt at the shop last night (it WAS today) Check engine light had popped on and it had been starting to sputter and surge at the idle occasionally for the last few days so I took a look at the MAF and saw dirty wires. Aha I can fix that, a couple squirts of MAF cleaner, plug it back in and voila! No more light, the Banana ran down the road around the block, over the hill and through the dale like a champ. I shut her down and call it a night.
This morning, hop in and fire the Banana up like usual and all I get is a nice peppy crank over. The Banana has had a bunch (pun intended) of new parts throw at her recently... new battery, starter solenoid, plugs and fuel pump relay and fuel filter. All within the last couple of months.
Out of complete disbelief, I ground on the ignition for a little while and she finally kicked over and sputtered to life. I let her idle a couple of minutes and things seemed fine so off we go. I make it about a block before the Banana starts hiccuping and bucking like something possessed and dies.... kaput.
The Banana has a 3.0, manual transmission and at least half a tank of fuel. Long story short and a tow truck ride home again, half a day trying unsuccessfully to pull a code, any code.... nothing. She will half-heartedly cough and spastically run with ether shots and near as I can tell I'm not getting fuel to the fuel rail relief port. I'm really hoping there is some way to diagnose a faulty fuel pump without having to drop the tank and fish the damn thing out.
I'm not hearing it run when the ignition is turned on but then again I don't think I've ever heard it run. Any other things to try before I replace the pump itself???
View 13 Replies
My ranger is an 89 but it's got a 91 motor in it, 2.9 V6. When I accelerate it hesitates before actually accelerating which makes me think the TPS is bad. Probed and tested and I got .85V throttle closed and 4.65 at wide open. Specs call for .8V - 4.5V
I'm not sure if there's an allowance of fluctuation, but is that high enough to point out a bad TPS? If it's not the TPS, is the ignition timing off or what else could it be?
View 8 Replies
1991 2.3 l. Thought I had an exhaust manifold Leak. Replaced gasket. New gasket didn't work. Removed gasket and mounted manifold to engine metal to metal, still and noise. Installed New manifold with gasket. Still same noise. Am thinking noise not coming from manifold. Torqued all bolts to spec. Could it be lifters .
View 9 Replies
Grandson 1991 Ranger 3.0 v6 69,000 miles We have a long start issue after it has sat for 30 mins. plus. If you open the throttle part way while cranking it will start fairly easily. Fuel pressure comes up instantly when you turn on the key. It runs at 39 psi pull the vac line off regulator it jumps to 49 psi. Fuel pressure does drop to about 30 psi after setting an hour. It kinda acts like it is flooded when it starts. so far we have done a complete tune up plugs wires cap and rotor. The ignition module has been replaced twice last one a real Motorcraft. New fuel pump and filter. Cleaned the fuel injectors with Ford cleaning system. I will replace the coil next and maybe clean the iac.
View 14 Replies
I have a 91 Ranger that the A/C was working great in but all of a sudden it stopped working even the fan. I turned it of and back on and it started again but then just stopped for good I can get the fan to work sometime, but no cold air. What it might be?
View 2 Replies
I can't get power to the fuel pump on my 91 ranger 3.0 5 speed. I just bought the truck and replaced all the relays checked all the fuses under the dash and under the hood. If I jump the relay it comes on and wont go off.
View 14 Replies
