Ford Ranger / B-Series :: 1989 - Tranny Input Shaft Seal Replacement?


Nov 25, 2013

I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.

Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.

View 1 Replies

Advertisement

Ford Ranger / B-Series :: 1999 - Output Shaft Seal Won't Stay?

I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.

99 2.5 auto. I changed the trans pan gasket too. No leaks from it.

View 14 Replies

Ford Ranger / B-Series :: 1989 - Side Wiper Quit Working - Shaft Location?

This morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.

View 14 Replies

Ford Excursion :: Drips Coming From Rear Axle Input Shaft Seal

I have noticed a few drips coming from the rear axle input shaft where the drive shaft connects. It has only done it once and there is no residue on the trailer hitch so I know it didn't dump everything on the road. If change this seal, how difficult is it and do you have any information which might make it easier.

View 14 Replies

Golf IV / Jetta IV :: 2001 - How To Access The Transmission Input Shaft Seal

I'm trying to get to the manual transmission input shaft seal on my 01 GTI w/12V VR6. I've removed the 3 bolts surrounding the input shaft but the metal shroud underneath the 3 bolts seems to be adhered tightly in place. You can see the 3 bolt holes and metal shroud in this photo: [URL]

Am I on the right track in trying to remove that shroud? If so, how do I loosen it?

View 8 Replies

Ford Ranger / B-Series :: 1995 - Replacement Of Carrier Bearing On Drive Shaft?

I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.

Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger

View 7 Replies

Ford Excursion :: Transfer Case Input / Front Seal Replacement

Noticed some fluid on the bottom of the Ex a few months ago and have been watching it since. Drained and refilled with the XL-12 fluid at the time and based on what I can see the likely culprit is the input seal on the transfer case. I have searched high and low both here and via the almighty google with little info to be found. Is it simply remove transfer case, replace input seal, reseal case connection, and refill?

View 2 Replies

Ford - Ranger :: 1997 - Transmission Rebuild / How To Take The Input Shaft Out

I have a 1997 ford ranger 4x4 5 speed manual. We are rebuilding the transmission ourselves, and taking on the task has been pretty hard. We are stuck at the input shaft. How to take the input shaft out? Do you need a special tool?

View 1 Replies

Santa FE SM (2001-06) :: Balance Shaft Oil Seal Replacement?

I have a 2001 4 cylinder Santa Fe. And atm I'm trying to replace the balance shaft oil seal but am having major problems getting it out.

View 2 Replies

Santa FE SM (2001-06) :: AC Compressor Replacement - Shaft Seal Is Leaking

After 9 solid years of service, my a/c compressor finally failed. According to the shop, its leaking at the center seam of the compressor. If the system is charged, then the compressor will operate until the low pressure switch shuts it down. My question is this: Can this compressor be rebuilt? If so, where can I get the parts (I'm assuming the shaft seal is leaking).

Also, a quick search on eBay provides several compressors that fit my car; however, some of them are listed as HS-17 compressors and others are HS-18. My car (according to the A/C sticker on the hood) says I have an HS-18 compressor. Are these two interchangeable? I'm asking because if the current compressor can't be rebuilt, then I will have to buy either a reman. or new unit.

Car: 2002 Hyundai Santa Fe, GLS, 2.7L V6

View 5 Replies

Ford Ranger / B-Series :: 1989 - No Power At All?

I have been thru everything i can think of except the main ECU on the ranger.

I've replaced the starter as well as the starter solenoid also the ignition switch.

What is happening is there is no power after the main wire to the solenoid from the battery. it doesn't power up anything. I've checked the fusible link and it appears intact. with a test light i can see that i have no power from the ignition itself i guess to tell the solenoid to work. i have noticed that the ignition cylinder is a little loose but what can cause there to be no power at all?

Could it be a bad solenoid?

View 2 Replies

Ford Ranger / B-Series :: 1989 - Grinding Noise When Let Off Gas

I have a 89 Ranger, 2.3, 2wd, Mazda 5 spd. Last year, 10,000 miles ago, I replaced the clutch, pressure plate, slave cyl, and pilot bearing. Today, it started making a terrible grinding sound/vibration when you let off the gas. The noise is coming from the clutch/transmission area. It is so bad that any amount of "engine braking" sounds terrible and I have to press the clutch in and the noise immediately stops. What to check for?

The only thing I can think of off the cuff is

1) bad pilot bearing,
2) low/no tranny oil. I replaced the oil and put silicone on the known leaky spots while I had the tranny out,
3) Input shaft had some "wobble" in it when I had the tranny out to replace clutch 10,000 miles ago.

This could be it but why would it start 10k miles later?

View 2 Replies

Ford Ranger / B-Series :: 2004 - Tranny Going Out?

Looking at buying a new truck. We'll in a crunch actually due to my tranny going out this morning. One that I'm looking at looks great, except the obd2 port is dead. Where do I start looking? What fuse etc. It appears auto correct changed the obd2 to body and I didn't catch it...

View 8 Replies

Ford Ranger / B-Series :: Drive Shaft Was Hanging From The Rear End

I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??

View 6 Replies

Ford Ranger / B-Series :: 1989 - Engine Sluggish When Cold

I have an 89 Ranger 2.3l with 255,000 miles on original engine. The engine runs like brand new. I'm just curious as to why it's extremely sluggish when cold. Example, it was 3 degrees this morning and I literally couldn't get over 45 mph for 5-10 mins. Everyone was passing me. No knocks or other strange noises just doesn't have any power. Once warmed up its completely normal. Obviously my '01 4.0 Ranger doesn't do this so I was mainly interested in why? Do they use different metal materials, is engine wore out (obviously it is to an extent), or something else?

View 2 Replies

Ford Ranger / B-Series :: 1989 - Proportioning Valve Cleaning?

89 4 wheel drive 2.9 5 speed can it be cleaned or cleared.

View 4 Replies

Ford Ranger / B-Series :: 1989 - Disengage Electronic Shift?

I recently acquired a 1989 Ford Ranger midsize pickup with an electronic shift button/console between the visors. I put it in 4WD and the manual does not indicate the procedure to take it out of 4WD. What is the procedure?

View 3 Replies

Ford Ranger / B-Series :: 2002 - Installing Used Tranny?

I am installing a used tranny in the ranger. According to the salvage yard the tranny fluid and filter was removed and fluid drained from the torque converter. How am I supposed to fill the torque converter?

View 1 Replies

Ford Ranger / B-Series :: 2000 - Burning Gear Oil Smell From Right CV Shaft?

In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?

View 6 Replies

Ford Ranger / B-Series :: 1990 - Front Transmission Seal Went Bad

I've got a 1990 ford ranger 4.0 auto trans front transmission seal went bad, I've got everything unbolted abs ready to come put but the trans won't come over top of the front cross member, what could be the problem on why it won't come out?

View 3 Replies

Ford Ranger / B-Series :: 1989 - Signs Of Water Leaking Through The Gasket

My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?

View 14 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved