Ford Ranger / B-Series :: 1989 - Heater Hose Leaking Around Behind The Valve Cover
Jun 19, 2015
Found a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
View 3 Replies
Advertisement
My truck has a 6 o powerstroke. I noticed some coolant loss, which I've been monitoring since I had the truck studded 2 years ago. Today I was looking around trying to find a cause of the coolant loss and I noticed some crusty orange residue on a hose that runs under the coolant reservoir. The hose seems to go behind the valve covers along the firewall to the passenger side through a steel line, and then go in a loop back to itself?
I'm guessing it's for the heater core, but I didn't see where it actually goes into the heater core, or anything else for that matter. It is a molded hose that has one of those crimped transitions into the steel line, so I'm not sure if patching it is an option or if I should look at replacing the whole piece. I'm guessing it's going to be expensive. From the fact that it never failed before, I'm thinking it wasn't originally routed with it touching the valve cover and was just something that happened after having the body off during the stud install.
View 7 Replies
89 4 wheel drive 2.9 5 speed can it be cleaned or cleared.
View 4 Replies
Bought my Ranger brand new, and I try to maintain it well. Most of the 90,000 miles are highway. Anyway, the OEM coolant was supposed to be good for 100K miles, but since I hadn't done anything in 89K, i have a lengthy commute and the coolant was getting discolored, I figured that no harm would come in having a drain/refill. This was approx. The heat worked flawlessly. Fast forward two weeks, and my local shop performed an oil change (not the quick lube that did the coolant replacement). I was informed of three things:
1) my coolant was low,
2) my heater control valve was leaking (which I was shown), and
3) when hoisted I was shown that a slight residue of coolant -- not necessarily fresh -- was on my water pump.
I was told that 'down the road sometime a water pump could be in my future'. Again, the heat worked flawlessly, and I didn't want to be out-and-about in winter and run out of coolant. So, the shop replaced my heater control valve and topped off the coolant (approx. 1/2 - 1 gallon). Heat worked flawlessly. The last couple days, I noticed two things.
First, heat trickles out on low and medium setting, and second, it takes a long time to warm the vehicle. So, my limited research tells me two things. If coolant is present, and I have heat (of some sort), then, the water pump and heater core are probably fine. Diagnosis says to check the thermostat first, correct?
View 6 Replies
My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?
View 14 Replies
I'm about to tear into a friends 2002 B2300 4 cyl. The lower hose that comes off of the coolant reservoir is leaking in the metal part of the line. Close to where it bolts to the block. At a glance, it looks like I have to pull the whole top of the motor apart to get it off since the line runs around behind the motor. Is there a trick to removing this coolant line without a lot of teardown? I'm not finding it at parts stores so I guess it's a stealership part.
View 2 Replies
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 Replies
My '98 B3000 has an oil leak. There is some oil up high on bell housing. So a buddy and I thought it might be the oil pressure sending unit. I replaced it. And still seems to be leaking.
Maybe valve covers? I was thinking rear main until we saw it on the bell housing. Valve covers don't seem to be leaking on the outside. Do they leak worse on the inside of the V?
View 5 Replies
I have a 2003 ford ranger 2.3 vin d 5 speed, this truck originally... Took it in for wires plugs front brakes fuel filter battery and added a small cold air intake. We discovered a valve cover leak and while repairing guy drops a screw into a valve and when finished he started it lodged the screw between the valve, shearing off a cam sprocket bolt. Throwing the timing. 2 valves on the exhaust side were bent and replaced. no damage to the head.
Timing was reset and the truck was running. 2 days later truck is running/had a hint of exhaust smell then started bogging dying and shaking, at which time we got an 02 bank2 lean code and fixed that. it cleared code and didn't fix it. From there we replaced coil, imrc intake bc of a crack, tried and check all vacuum, reset the timing. Timing would slip before but no longer than 10 minutes every time truck started.
Found the hole in the timing cover that holds the bolt to torque? to harmonic balancer was broke. replaced along with the diamond washers and cam sprocket bolts. timing finally held crank sensor was adjusted. truck came home for one day running good, we had removed the cold air intake and replaced the factory air intake. next day it was so slow outta first gear, you must baby the throttle, if you floor It, it sputters and kinda pops, truck stays slow all the way to about 10 mph and 2000rpm then it begins grabbing speed, 3000rpm is where this truck shifts the best, 2nd is better, third better than that.
As rpm increase the truck runs better, it idles steady at 1100-1200rpm at stops with an audible miss and then struggles again on takeoff. Here what im wondering, the truck has an abs sensor that just came on, but no codes showing now.tomorrow I wil run matko determinator 3.0 on it. and test the catalytic converter. first how do I check the timing belt to see if it stretched? do these trucks store the p.i.d.s. koer or kams that could cause one, all, or any of this and if so do I have to have it flashed from ford or can you manually do this without a drive cycle test.
View 2 Replies
My 2000 Ranger has been leaking fluid around the front Diff cover so I decided to pull the cover and reseal it. It was obvious that this was going to be a tight job but I didn't anticipate running into a bolt that can't be removed because interference from the front cross member.
View 3 Replies
Either one of my power steering hoses or the gear box is leaking on my 93 Ranger. It appeared the return hose was leaking where the rubber meets the crimp. So I decided I would go ahead and change the return and pressure hose to see if it stops the leak. It was a disaster. It's 2.3L manual transmission 4x2. I got the return hose off ok. I put the wrong size wrench on the pressure hose fitting at the pump but thought it was loosening but it was rounding the nut off. So I couldn't even change that hose. I installed the new return hose and retightened the pressure hose at the gear box.
Well it was a pain getting the flare fittings of the hoses into the steering box so I could tightened the flare nut down. I finally got them tightened, I think, but then when I started the engine fluid shot out of there like a water hose. It's coming from the fittings at the gear box that I thought were tightened. I reloosened and retightened them again and still it's shooting out everywhere. There is so little room getting a wrench on the hose fittings, it was slow going. What do you need to remove in order to get a good straight shot and installing these flare nut fittings and tightening them down right? If I remove the pump will it be easier to install the hoses on the gear box? I have to remove the pump now to change the pressure hose.
View 1 Replies
I have a 89 ford mustang with 4 cylinder. After being stored for the winter I noticed anti-freeze leaking from drain tube below heater core (small amount). I am not looking forward to replacing the heater core in this car! Any reason this happened after the car sitting in storage all winter??? or just a coincidence??
View 7 Replies
Passenger side valve cover leaking. My local parts stores have two brands.
Fel-Pro and MAHLE Original.
Any comments, preferences, anecdotes? I don't want to do this job twice.
View 6 Replies
My wife has a 2004 escape v6 (3.0L). The valve cover seal was leaking so I decided, why not change the plugs since I'm already going to have the intake manifold off.
I got down there, replaced the seal (just the front side, didn't want to disassemble something that wasn't broke) and then replaced all 6 plugs and boots (with springs). Fired it up and everything seemed fine. She went to drive to work and the CEL started to flash. I read the code and there were 4 (Don't remember exactly what they were), but it was a combination of things resulting from a misfire in cylinder 4. Since it was one of the front ones. I just pulled the plugged and replaced it hoping I had gotten a dud from the factory. Nope, still doing it.
I didn't take off the fuel lines, just the air intake on the top. I did not change the coils, but everything was running fine before I changed plugs so logic would dictate it is something I did. Only seems to misfire at higher speeds. Also, her battery light randomly comes on, but the battery and alternator test good. This has been happening a while.
View 4 Replies
On the manifold there is a metal/steel pipe that the heater hose hooks to. That pipe is leaking anitifreeze. It has a small hole in it. Is this pipe replaceable or is it part of the manifold.
View 19 Replies
I had it checked out at the dealer and they called it a "weep" so they went on to tell me that VW probably wont approve warranty work for it. I pushed for them to take pictures and send it in anyway.
Now assuming they won't do it, I have been looking for a DIY or a technical order on the job but I can't find anything.
View 7 Replies
Just found valve cover of my Tiguan is leaking out oil this morning. Will go to dealer tmr for gasket replacement. My car is just over 50k miles. What happened to VW's car quality control???
View 5 Replies
Haven't had the engine cover off for about 25k now (cleaned it up under there last time I changed plugs.) Took it off today and noticed it's a little oily on all four sides around the valve cover.
Pretty sure I can account for the oil that's near the filler cap... I don't recall spilling enough that would completely go around the entire valve cover though...
But how did it end up so high on top of the valve cover on the corners? It's even a little wet looking on the back if you look hard enough..
I only have 4600 miles left of the 10/100 warranty so I'm glad I caught this and hope the dealer can do something about it... or are they going to tell me this a "normal" amount of seepage? I haven't owned a vehicle with plastic valve covers before so I don't quite know what to expect.
View 7 Replies
I took it to the stealership to get the alternator and some vac. lines replaced all under an extended warranty. They informed me that both valve cover gaskets and right side cam adjuster gaskets are leaking. By no means am I a mechanic or close to but I am trying to get this stuff done as cheap as possible so I am going to try to tackle this myself.
View 3 Replies
So, weird smell that I thought was burning plastic or rubber is actually hot oil leaking from the valve cover and tensioner gaskets.
My car is nearly 8 years old (2003), and has about 70K. Should I go ahead and buy a timing belt kit and replace all that stuff at the same time?
View 1 Replies
My son-in-law came by tonight and showed me his ticket from his oil change at the dealer on his '08 Azera, 108k miles. Tech remarked that both valve cover gaskets AND the oil pan gasket were leaking. I've walked through his garage many times when my daughter has the car at work and I've never noticed any oil on the floor. Should have I seen any? I told dealer I would just drive it and monitor the oil level and any other signs of oil leakage. Since he bought the car with 101k miles and a fresh oil change ticket and never checked the level over the next 7k miles I don't think it's leaking bad.
View 2 Replies
