Ford Ranger / B-Series :: 1987 - Running Extremely Rough / Exhaust Smell
May 20, 2015
I have a 87 ford ranger pickup, it is running extremely ruff. You can smell the exhaust and it smells super rich and is even spitting fuel out of he exhaust. when I bought the truck the wires were cut on he oxygen sensor, so I put a new oxygen sensor in it hoping that it would lean out the fuel. The truck has duel tanks on it, but the back one is off and it is draining fuel out of the line when it is running. I don't know if the catalytic converters are plugged too, the truck only has 65,000 miles in it. or maybe its a vacuum line leak?
View 4 Replies
Advertisement
How many O2 sensors does a 2.3 fi 4 cyl. have. I think just one on the manifold, but I'm not completely sure. Engine is running very rough and seems to miss at low RPMs, has no power and drinks gas like crazy!!! Emissions light is on on the dash. I'm thinking O2 sensor......tried replacing, but couldn't get enough torque on the sensor socket wrench to loosen, may be rusted.
View 6 Replies
1994 reg cab 4.ol 13ok.. my wife just got it, been doing some small things like replaced dome light, replaced cargo/third brake light, truck starts and seems to run ok. but i get a headache in it which i believe is carbon monoxide, has a leak or something? i text previous owner, he said he replaced 02 sensors, but didnt say if they were bosch or a good brand.. also trucks has a oil pressure and coolant temp gauge fitted on by the gear shift as the dash gauges for those functions are out. Does this mean the CTS may not be working and affecting fuel/air I do not know these trucks i only just found out what this strange silver looking thing was it is the IAC, I Believe, then there is this black plastic vacuum type cylinder by the passenger side firewall, what is that? and right against the drivers side fire wall is a small reservoir type thingy, is this something to do with ABS? i do have an ABS light on, was hoping it was the bulb out on the third brake light or something quirky like that no such luck its still on after starting engine. but i am concerned about this running rich/strong smell as we really cant take it far as is it, its dangerous, may have to get a smoke test? Just got the truck, trying to get caught up..
View 8 Replies
2002 Ford Ranger edge 3.0 flex ... Truck was running fine and giving me no issues. I woke for work the other day and went to get coffee and truck wouldnt start. I could hear fuel pump running and knew it wasnt that, it was acting flooded. So today I pulled fuse from fuel pump relay, and got it to start. Put the fuse back in and ran to gas station. On the way to the gas station it started running really rough, very low and rough idle, trying to stall out. I noticed it had black smoke coming from exhaust. I got it home, and got it to start barely, and it has the same very low and rough idle, but my oil gauge was going crazy, flickering back and forth all crazy, and the idol is terribly rough and eventually stalls out. Earlier today I did put new spark plugs in it, but not sure that has anything to do with the issue. I also hooked it up to a computer and it isnt throwing any codes.
View 13 Replies
I own a 1990 Ford Ranger, 2.3 EFI with an 8 Plug setup and 2WD. It uses a dual-coil system an not a distributor if that means anything here.
Okay, so for the last week I have been experiencing extremely high oil pressures. My gauge would read almost as high as the "H" mark. The smell of burning oil was heavy in the cab from the vents. I took it easy, made sure my oil level was good and I had enough oil, the truck drove rough, but drove decent.
Yesterday, I got done sliding in some mud (not crazy bouncing or anything, just sliding). I stopped at a stop sign, turned around and hit the gas, and the truck died. I thought there were other issues not related to oil, however I noticed that the oil gauge now read about an inch left of the "L"ow mark. If I turned the key, to the "ON" position, the gauge pushed the needle to above the left gauge itself pointing towards about the "8 oclock" area.
Now, my truck will not start. It cranks and cranks and cranks with no start. I called a bunch of mechanics and none of them knew what I should do. AutoZone did not know what do, no one did. Some people said that the oil pump itself had gone out and that would cause the truck not to start and would cause gauge issue. Others said that it might be as small as the Oil Pressure Switch. Firstly, I bought a new Pressure Switch. Have not installed it because I cannot find the damn thing.
Where the switch OFFICIALLY is. I have read on Google that it is on the passenger side, at the rear end of the cylinder head. Other posts say it is by the oil filter...
PICTURES:
Without the key in the ignition:
With the key in the ignition, in the "ON" position:
View 14 Replies
Still cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 Replies
Having some trouble with my 1987 2.3L ranger - 2wd - Non AC - 107k miles.
The truck feels like its running on 3 cylinders and occasionally stalls. Motor has a pretty good shake to it while idling as well.
Recently replaced injectors, rotor, cap, wire, spark plugs. Timing belt was done approx 30k miles ago.
Put seafoam into it. Problem persists - where to go from here ?
View 3 Replies
I have an 87 ranger, 2.3 4cyl. 2wd 5 speed. When I start up the truck after it sits for a few hours it will idle fine but then it starts to bog down and wants to stall but after about 5 mins its fine and runs like a champ. I don't know if its a sensor or what.
View 2 Replies
My brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
View 4 Replies
1987 Ranger and the computer will not communicate. I'm trying to check for codes because of a rough idle and stumble when starting out from a stop. Check engine works but won't flash when using a jumper across the data link. Used a OTC scanner but it only times out and comes up "no data". Where to go from here?
View 7 Replies
I have a 87 ranger with a 2.9 and recently it started to act up when i start after its been sitting for a couple hours it has a rough rolling idle and will stall out and a lot of white smoke out the tail pipe and some times a tiny bit of black smoke when revved high....after a about 10 mins of feathering the gas it will even out and runs no problem.... oh and quite a bit of moister comes the tail pipe....and this issue just occurred over night every time before never had an issue like this...
View 5 Replies
I have a 87 F250 with a 302. Every time I drive it I smell like exhaust. Doesn't matter how short or long the trip, but the longer the trip the stronger the smell when you get out. I found 1 loose manifold bolt and tightend it, but no difference.
View 13 Replies
I have a 2003 ford ranger 2.3 vin d 5 speed, this truck originally... Took it in for wires plugs front brakes fuel filter battery and added a small cold air intake. We discovered a valve cover leak and while repairing guy drops a screw into a valve and when finished he started it lodged the screw between the valve, shearing off a cam sprocket bolt. Throwing the timing. 2 valves on the exhaust side were bent and replaced. no damage to the head.
Timing was reset and the truck was running. 2 days later truck is running/had a hint of exhaust smell then started bogging dying and shaking, at which time we got an 02 bank2 lean code and fixed that. it cleared code and didn't fix it. From there we replaced coil, imrc intake bc of a crack, tried and check all vacuum, reset the timing. Timing would slip before but no longer than 10 minutes every time truck started.
Found the hole in the timing cover that holds the bolt to torque? to harmonic balancer was broke. replaced along with the diamond washers and cam sprocket bolts. timing finally held crank sensor was adjusted. truck came home for one day running good, we had removed the cold air intake and replaced the factory air intake. next day it was so slow outta first gear, you must baby the throttle, if you floor It, it sputters and kinda pops, truck stays slow all the way to about 10 mph and 2000rpm then it begins grabbing speed, 3000rpm is where this truck shifts the best, 2nd is better, third better than that.
As rpm increase the truck runs better, it idles steady at 1100-1200rpm at stops with an audible miss and then struggles again on takeoff. Here what im wondering, the truck has an abs sensor that just came on, but no codes showing now.tomorrow I wil run matko determinator 3.0 on it. and test the catalytic converter. first how do I check the timing belt to see if it stretched? do these trucks store the p.i.d.s. koer or kams that could cause one, all, or any of this and if so do I have to have it flashed from ford or can you manually do this without a drive cycle test.
View 2 Replies
My car was running rough, with white smoke and strong gas smell coming from exhaust. It died out on me a few times as if it was not getting enough acceleration. Well, I coded it and said misfire cylinder 3 and 4. I also tried to shut down 3 and 4, but did not shut down. I switched 3 and 4 with 1 and 2, still did not shut down cylinders 3 and 4. Engine coils are good, engine module was tested and passed twice. Ok, fuel injectors 3 and 4 were leaky and I changed them out. New spark plugs and boots. New oil and filter..(There was gas in my oil and oil in my air filter.) With the new parts....my car sounds soooo much better!!! still a little rough, does not bog down, but it still has the strong gas smell and white smoke from exhaust..(gas smell soo bad I had to open all doors to the garage!!) What else could be wrong?!?! I'm getting frustrated!! It also has NOT ever over heated, does not run high.
View 7 Replies
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 Replies
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
View 8 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 Replies
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
View 8 Replies
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
View 14 Replies
