I have an 87 Ranger and the oil pressure gauge is slow to respond changes in pressure. Is this the way the gauge is designed to work or do I have a bad sending unit?
View 4 RepliesI have a 97 Splash with the 3.0, oil pressure goes up to about the middle of the gauge after startup, however, it stays there whatever I do, warm/cold, idle/5500 rpm. Is it supposed to be like that?
View 4 RepliesMy oil pressure gauge does not work. I was told that it's most likely the sensor. Where would I find this to change it out?
View 3 RepliesI have a 2002 Ranger V6 3000 with 100K miles. Can I add a higher viscosity oil since my pressure gauge is acting up. I changed the sending switch twice but the gauge still acts up occasionally. I was thinking of adding 10/ 30 on my next oil change. I do live in the area where the air temp is quite high in the summer. The truck runs well except for the oil gauge, in my opinion, is giving false readings.
View 14 RepliesI have a 2001 Ranger 4.0, 4x4 that just hit 100k and the oil pressure gauge doesn't show a reading for about 1 minute after startup. Also, the check gauge light comes on. What do I replace to fix this and is it something I can do myself? I am mildly handy. Would you worry about fixing it or just let it go because it's obviously getting oil pressure.
View 2 RepliesYesterday went to fill up ($4.05 a gallon geezz!) and noticed that after getting back into the cab, the fuel gauge still showed almost empty. So after yelling a few expletives, I looked again and noticed the gauge starting to make it's way up the dial. It took almost 30 min. before it showed almost full. I'm not sure what the problem is, as the gauge seems to still function. I don't drive the truck much as I use it as a tow vehicle. However, I do try and take it for a spin about 3-4 times a month just to exercise it. I was wondering if the fuel has started to gel and that is the reason for the slow fuel gauge response. Should I add a fuel conditioner/cleaner now that I have a full tank?
View 9 RepliesI just bought an older 1995 Ranger XLT 4.0 I was told that the truck is stuck in overdrive. The overdrive light is not working and the button does not respond. It shifts smooth but run away with it's self. It is not shifting a lot going up hill and curves.
I got a diagnostic and it did not show codes. I was told the trani has had an oil change and filter with no metal parts in the oil. Since the overdrive switch is know for a short in the steering column maybe when they looked at it they did not know what they were doing.
I am driving it only once or so a week. But don't want to hurt it. A friend did the first work and had it diagnostic done yesterday.
Which transmission came with the 1987 Ranger 2.9L?
View 4 RepliesI have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
I have a friend who drives a 1987 ranger 2.3 4 cyl and is having problems with oil building up in his air cleaner. I thought maybe it was a bad pcv valve or worn out rings. I looked at it and cannot even find a pcv valve on it. it has one hose that runs from the valve cover to the air clean but there' s no valve in it. are the rings shot or what is causing this to happen?
View 6 RepliesStill cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 Repliesso I have a 1987 2.9L Ranger that likes to stall out when its idling after reaching temperature. Ive replaced all sorts of sensors (IAC, Coolant Temp, and PCV) and so far no luck. I was trying to figure out what the relearn procedure was for the IAC or get an input on any other possible sources of error. I haven't changed TPS yet.
What the engine does is when it gets up to temp, the engine will start to loose speed, and will start to shutter. Then it'll kick back up run fine for a few seconds and drop again, it'll do this for a few minutes then completely just choke out.
1987 ranger 2.9l... My truck had no power while accelerating. We'll I changed fuel pump and filter. And still no power. I bought a computer and it tells me the map sensor is not at normal vaccum levels. The ego sensor is reading always rich. Egr valve not opening. Knock sensor was was going crazy. And computer couldn't raise engine speed above normal idle. Could all this be because of one sensor or should I just change it all.
View 7 Replies1987, 2.9 ... I got all my wiring repaired and replaced both the intank pump and the high pressure pump, for a few days it would fire right up as soon as you hit the key but it had a miss (the pumps shut off after a second or two with the key on "RUN"). I tore the throttle body off and cleaned all the carbon out of it, when I put the throttle body back on I noticed that the engine to body ground was loose so I ran a new piece of 4ga from the intake manifold bolt to one of the master cylinder bolts.
After I did this I went to start the truck and no go, the fuel pump turns on with the key but then it wont shut back off until you turn the key off. if you try and start the truck it will crank but wont fire, after about a half hour of cycling the key and cranking it will start to put a little bit then a few tries later it will start but sounds rough when it first fires. I thought it may be a stuck injector so I ran some cleaner through the Schrader valve on the rail. Still have nothing, both pumps do run but still don't shut off after a few seconds like they should and now it wont even try to start.
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
I just bought a 87 Ford Ranger 2.9L v6 4x4. It has a tick to it. It doesn't stop, it doesn't increase with acceleration it stays the same. I sprayed some SeaFoam in it and It improved the performance a lot (More horsepower, better reaction to the pedal.) But it is still knocking. I have never tore apart an engine before or messed with lifters or anything. I'm not completely sure how to fix it. I know knocking is not a good thing either.
View 6 RepliesI have a 1987 ford ranger 4x4 2.9l v6 but my transmission slips out of gear and its auto im not sure why but ive been told im missing a over drive gear is this a possibility or what???
View 1 RepliesI was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.
View 1 RepliesI have a 1987 ford ranger, it has a 2.0L carborated motor and I also have a 1994 ford ranger fuel injected motor I believe it's a 2.3L, I am wondering if the swap will work to put the 94 motor in the 87....
View 3 RepliesMy dash light fuse blew. I checked with a meter and I have a short to ground somewhere in the wiring for the lights. Everything else seems to be working fine.
Is there a copy of the wiring diagram somewhere?
I have the big ford shop manual but I't doesn't have any diagrams. (might be missing pages, I got it off Ebay and the index is missing T-Z).
I have the Haynes but it doesn't have the diagram for the dash lights.
I have a 1987 ranger 2.9 V6. Have a intermittent miss @ idle when warmed up. What is the proper way to pull the codes from the computer, i,st something about counting flashes or lights...
View 6 Replies