Ford Ranger / B-Series :: 1987 - Escalating Ticking Noise Progressed Over 50 Miles Of Driving
Dec 1, 2014
Dad gave me an 87 ranger 7 months ago. After correcting a few transmission issues, and complete head job my truck was running great. Drove her the last two weeks, then she sat over. Today I took her out around the city and noticed a slight ticking sound. The noise progressed over 50 miles of driving. I finally decided to take her home. My mechanical knowledge is minimal, and need to know where to start troubleshooting. My wife says she heard a loud ticking noise right before she blew the head gasket a few months ago ( this makes me even more concerned) could this have anything to do with the late cracked head gasket issue?
View 3 Replies
Advertisement
Yesterday I was driving around some back roads and I started to hear a ticking when I accelerated when I left my foot off the gas pedal it went away. But when i put my foot on the gas again it comes back. You really cant realize it when you have the radio on... Ive been experiencing rough idling when I come to fast stops and quickly speed up again.
The ticking seems to only happen after like 20 minutes of driving. Most of my trips are only 10 minutes, to either school or to work so it really doesn't happen very often... Although college will start in a few months (30 minute drive) so I wanna get this fixed before something major happen.
Also on a side note, when going up hills it feels like it has delayed shifting. I really don't want to put in anymore money into this truck...already put $ into it the first year of owning it. I guess the good thing is that I got it keeping my fingers crossed nothing is wrong with the transmission or motor, what is wrong?
*I have a 1995 v6 4.0 XLT ranger with 160,000 miles
View 7 Replies
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
View 6 Replies
1987 ranger 2.9l 4wd 5 SPD ... I just replaced plugs wires distributer cap and rotor and pcv valve and hose. It drives fine for about 3 minutes and then it looses all power and I can't get out of 2nd gear. It idles fine all day long. The guy I bought it from said he put a new tank and pump on it.
View 3 Replies
1998 ranger 5spd... I have 117k miles on this little ranger and I recently took it on a little trip and since that trip it has a ticking noise under the hood as if the lifters were sticking. I believe it has hydrolic lifters in it. I put some sea foam in it 200 miles ago and changed the oil about 50 miles ago. I used Valvoline full synthetic and it seems like it has lessened the tick and it drives a lot smoother, in my opinion. Is there any thing else I can do to relieve that ticking? It is more noticeable when the engine first starts and is louder if i push down harder on the gas. It is not preset if i do not put that much pressure on the gas.
View 6 Replies
Which transmission came with the 1987 Ranger 2.9L?
View 4 Replies
I have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
View 1 Replies
I have a friend who drives a 1987 ranger 2.3 4 cyl and is having problems with oil building up in his air cleaner. I thought maybe it was a bad pcv valve or worn out rings. I looked at it and cannot even find a pcv valve on it. it has one hose that runs from the valve cover to the air clean but there' s no valve in it. are the rings shot or what is causing this to happen?
View 6 Replies
Still cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 Replies
so I have a 1987 2.9L Ranger that likes to stall out when its idling after reaching temperature. Ive replaced all sorts of sensors (IAC, Coolant Temp, and PCV) and so far no luck. I was trying to figure out what the relearn procedure was for the IAC or get an input on any other possible sources of error. I haven't changed TPS yet.
What the engine does is when it gets up to temp, the engine will start to loose speed, and will start to shutter. Then it'll kick back up run fine for a few seconds and drop again, it'll do this for a few minutes then completely just choke out.
View 3 Replies
1987 ranger 2.9l... My truck had no power while accelerating. We'll I changed fuel pump and filter. And still no power. I bought a computer and it tells me the map sensor is not at normal vaccum levels. The ego sensor is reading always rich. Egr valve not opening. Knock sensor was was going crazy. And computer couldn't raise engine speed above normal idle. Could all this be because of one sensor or should I just change it all.
View 7 Replies
1987, 2.9 ... I got all my wiring repaired and replaced both the intank pump and the high pressure pump, for a few days it would fire right up as soon as you hit the key but it had a miss (the pumps shut off after a second or two with the key on "RUN"). I tore the throttle body off and cleaned all the carbon out of it, when I put the throttle body back on I noticed that the engine to body ground was loose so I ran a new piece of 4ga from the intake manifold bolt to one of the master cylinder bolts.
After I did this I went to start the truck and no go, the fuel pump turns on with the key but then it wont shut back off until you turn the key off. if you try and start the truck it will crank but wont fire, after about a half hour of cycling the key and cranking it will start to put a little bit then a few tries later it will start but sounds rough when it first fires. I thought it may be a stuck injector so I ran some cleaner through the Schrader valve on the rail. Still have nothing, both pumps do run but still don't shut off after a few seconds like they should and now it wont even try to start.
View 12 Replies
I just bought a 87 Ford Ranger 2.9L v6 4x4. It has a tick to it. It doesn't stop, it doesn't increase with acceleration it stays the same. I sprayed some SeaFoam in it and It improved the performance a lot (More horsepower, better reaction to the pedal.) But it is still knocking. I have never tore apart an engine before or messed with lifters or anything. I'm not completely sure how to fix it. I know knocking is not a good thing either.
View 6 Replies
I have a 1987 ford ranger 4x4 2.9l v6 but my transmission slips out of gear and its auto im not sure why but ive been told im missing a over drive gear is this a possibility or what???
View 1 Replies
I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.
View 1 Replies
I have a 1987 ford ranger, it has a 2.0L carborated motor and I also have a 1994 ford ranger fuel injected motor I believe it's a 2.3L, I am wondering if the swap will work to put the 94 motor in the 87....
View 3 Replies
My dash light fuse blew. I checked with a meter and I have a short to ground somewhere in the wiring for the lights. Everything else seems to be working fine.
Is there a copy of the wiring diagram somewhere?
I have the big ford shop manual but I't doesn't have any diagrams. (might be missing pages, I got it off Ebay and the index is missing T-Z).
I have the Haynes but it doesn't have the diagram for the dash lights.
View 4 Replies
I have a 1987 ranger 2.9 V6. Have a intermittent miss @ idle when warmed up. What is the proper way to pull the codes from the computer, i,st something about counting flashes or lights...
View 6 Replies
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 Replies
I have a 1987 Ford Ranger that only has high speed on the wipers. According to the Ford Shop Manual the probable cause is the interval windshield wiper governor, which is suppose to be mounted above the driver's side kick panel. The manual even shows a drawing of the governor and the location. Nothing is there in my truck. Where it is located and what it looks like?
View 14 Replies
I am having a problem with my dashboard lights blowing fuses. I bought an 87 Ranger XLT, and found that the dash lights didn't work. The 5 amp dash light fuse was blown, and the dome light would not come on using the switch. I replaced the fuse with a 15 amp and replaced the headlight switch which had melted the connector at one of the terminals. The dome light now comes on using the switch and I was able to get the dash lights to come on at a very low setting, but the headlight switch will smoke some.
But when I turn the switch to brighten the dash lights, it causes the tail light fuse to blow. I don't see how the dash lights could blow the tail light fuse, but it happens as soon as I install a new fuse and brighten the dash lights. What is going on? I think it is probably a short somewhere, so I pulled the instrument cluster and looked at the wires, didn't see anything exposed.
View 7 Replies
