1987 ranger 2.9l 4wd 5 SPD ... I just replaced plugs wires distributer cap and rotor and pcv valve and hose. It drives fine for about 3 minutes and then it looses all power and I can't get out of 2nd gear. It idles fine all day long. The guy I bought it from said he put a new tank and pump on it.
View 3 RepliesI have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 RepliesRecently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
Dad gave me an 87 ranger 7 months ago. After correcting a few transmission issues, and complete head job my truck was running great. Drove her the last two weeks, then she sat over. Today I took her out around the city and noticed a slight ticking sound. The noise progressed over 50 miles of driving. I finally decided to take her home. My mechanical knowledge is minimal, and need to know where to start troubleshooting. My wife says she heard a loud ticking noise right before she blew the head gasket a few months ago ( this makes me even more concerned) could this have anything to do with the late cracked head gasket issue?
View 3 Replies5.0L V-8, Electronic Fuel Injection, 79,000 miles, 2 WD, 4 speed manual. I'm the original owner.
If I drive it 4-5 miles on secondary streets (25-40 MPH) it shuts off without warning after 10 minutes and will not restart without a 20-30 minute wait. If I drive it 2-3 miles and park it for a couple of minutes it will not restart without waiting 20-30 minutes. Checked engine water temp gauge and it is normal.
The local mechanics found no spark when it failed at their garage. They replaced the ignition module on distributor. This did not fix the problem. In their second attempt they replaced the coil. Still the same problems persists and the mechanics are stumped.
It's like something in ignition package heats up after 10 minutes and either sticks open causing no spark or closes shorting out the spark if that is possible. What is causing this and how to fix it.
1987 ranger 2.9l... My truck had no power while accelerating. We'll I changed fuel pump and filter. And still no power. I bought a computer and it tells me the map sensor is not at normal vaccum levels. The ego sensor is reading always rich. Egr valve not opening. Knock sensor was was going crazy. And computer couldn't raise engine speed above normal idle. Could all this be because of one sensor or should I just change it all.
View 7 RepliesWell it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 RepliesMy brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
I have a 1987 Ford Ranger 2.3L, it's the truck I learned to drive in (stick at 13yo) and the 1st car I crashed too... So now this baby is almost 30 years old and recently had a minor restoration...
Engine was pulled out and all gaskets were changed, spark plugs, wire... All that stuff... It has been running pretty good, however last week a water line broke on the Left side near the spark plugs (if you are looking at the truck)
Since then It has absolutely Zero power. The slightest hill and even when pedal to the floor will lose power. Yesterday went from the start of a hill at 60mph in 4th to 20mph in 2nd because it didn't have the guts to go 1/3 mile uphill... I checked everything I could, and my brother took it to the exhaust guy who made a small hole on the Catalytic Converter and said it was good, but he could tell it was running too rich...
I replaced some of the vacuum lines last night, I found a lose one on the fuel pressure regulator (I think that's what it is, Its towards the engine firewall on top).
Idles beautifully, drives great, no rough shifting, pinging or knocking, no misfires. So that's what has me stumped... Runs great but just no power... Also before water line broke it was running fine with power...
1987 Ford Ranger
2.3L FI
5sp manual, Rwd
I have a 97 Ranger, v6 4.0L, 2wd, 5spd. It has been my daily driver since 1999. I was driving to work today and when I pulled into the parking spot, I turned the truck off, and I thought it was odd that the locks didn't pop up when I shut the truck off.
I then realized that I had completely lost all electrical power. Tried to turn the truck on and nothing. No click. No dome light, no horn, no nothing.
My battery reads 12.5 volts and the connections are all clean on the battery. I checked all the fuses and they are all good. What else should I check? This may be the first time this truck has ever stranded me before.
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 RepliesI have a 1992 Ranger with 2.3L that suddenly lost power on freeway and stopped and couldn't restart. Towed it to Seattle, WA and need Ford Ranger 2.3L engine mechanic to double check the timing since new belt installed to make sure it was done right before cover and rest of engine reinstalled.
View 5 RepliesI have a 94 Ford Ranger 4x4 4.0 V6. It has developed a rough idle and has lost i fair amount of power. I cleaned the maf sensor and iac valve. Along with replacing an o2 sensor that was reading bad, with no improvement. The guys at O'reilly took a look and think I may be dealing with a timing issue or a warped valve. My question here is to found the culprit? I'm very inexperienced at working on vehicles and am damn intimidated by the scale of a project like timing. I should add that while traveling on the highway in high gear at low rpms, it develops a rough stutter. I can either power through it or ease off to get it to stop, but it resumes shortly after. It almost acts like an egr valve stuck open when on the highway. But that doesn't account for the rough (a consistent put, put, put...) idle.
View 4 Replies02 Ranger with 3.0 Flex motor, 375K+ miles. Been chasing an issue for a while now, but am about at the end of my diagnosing capabilities. Issue started with a misfire on 5 and rough running engine with no codes showing up. Now the motor is getting worse.
Idle a little rough and no power when accelerating hard. The engine sounds like a popcorn popper under hard acceleration. Motor revs up to 4K but does not pull or shift gears until I let off the gas.
The code that initially showed up indicated a bad Camshaft Position Sensor. Changed that and the Sync assembly - as per instrucions, exactly positioned same as old one. New codes showed up - P1152, P0175, P0171. Cleaned the MAF, rail fuel pressure OK, can't find any vacuum leaks, replaced both upstream ox sensors, and changed #5 ,6 injectors.
Motor still runs the same - like crap, like a corn popper on acceleration, smooths out if only slightly accelerating, but stumbles n bumps on steady cruise speed over/around 60 mph - and no codes showing at present.
I really, really don't want, nor can I afford, to take it to the dealership, but I may be forced to if I can't figure this out sometime quite soon. I make my living with this truck so, no truck, no work till this issue is solved.
I was pulling out of a parking lot making a sharp turn when all the sudden I lost my power steering. I have a '94 Ford Ranger manual transmission. It didn't make any sounds. I was going to try to keep adding power steering fluid to it and try to get it home to my mechanic in my hometown - but it drips constant liquid when I drive it down the street (you can see drips) so I don't think that's possible. I've read a lot on here about gear boxes failing, but would this cause it to leak even if the truck wasn't running? (the puddle builds quickly when its just sitting there, engine off). I took it to a mechanic (I don't have tools), and they said they can't say anything for sure until they look around, it could be seals or a new gear box.
View 2 RepliesWhich transmission came with the 1987 Ranger 2.9L?
View 4 Replies I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
I was driving down the highway when I lost all oil pressure soon after I lost power steering and the engine died. I have checked the radiator and it is still full of fluid pulled the starter off and try to crank it it still turns the cannot get the engine to turn over it clicks but wont turn over there are no oil leaks underneath the vehicle that I can see. I'm just not sure where to go or what to do from here
View 19 RepliesI have a friend who drives a 1987 ranger 2.3 4 cyl and is having problems with oil building up in his air cleaner. I thought maybe it was a bad pcv valve or worn out rings. I looked at it and cannot even find a pcv valve on it. it has one hose that runs from the valve cover to the air clean but there' s no valve in it. are the rings shot or what is causing this to happen?
View 6 RepliesStill cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 Replies