Ford Ranger / B-Series :: 1986 - Fuel System Wiring Diagrams?


May 11, 2012

Looking for the wiring diagrams for 86 ranger fuel system. I replaced the fuel pump relay after testing and finding that it was bad, still not getting fuel. I want to test any fusible links or anything else that could have gone wrong before I throw another part at it.

View 1 Replies

Advertisement

Ford Excursion :: 2003 - Wiring Diagrams For Lightning System?

I have a 03 Eddie Bauer PSD and I'm looking for wiring diagrams online. Specifically for the lighting systems. I bought a set of OEM telescoping, heated mirrors with turn signal and running lights and the running lights do not work. Appears that 03 may not have supported this but I see other rigs with the same mirrors and the running lights working.

View 14 Replies

Ford Ranger / B-Series :: 1986 - No Fuel To Rail / Truck Quit On The Way

I have a 86 ranger 2.9 5 speed. A few days a go I replaced the front fuel filter and all seemed ok. Last night on my way home the truck quit and I had to have it towed home. Now I find both pumps don't seem to be working. What would make me loose both pumps??

View 11 Replies

Ford Ranger / B-Series :: 1986 - Start Over Fuel - Idles Very Roughly - Stalls Out?

its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?

View 14 Replies

Ford Fuel System :: 1986 Ranger Starts Only When Spray Starter Fluid Into Air Intake

My 1986 Ranger 2.9 starts only when I spray starter fluid into the air intake. It does stay running and it drives fine. The engine will not fire up unless I do this process. I have cleaned out the fuel rail, fuel injectors, purchased new fuel filter, and tested fuel pressure (which is good).

View 9 Replies

Ford Ranger / B-Series :: 2007 - Replacing Pioneer Audio System - Dash Wiring Harness?

I'm going to replace the bone stock/non-"Pioneer Audio System" radio with a new Pioneer head unit in my 2007 Ranger Super Cab. After looking at the wiring between the third-party Metra Ford adapter and the supplied Pioneer harness, I'm left with a couple of connections that must be made to other wiring harnesses in the dash.

First up is a wire from the supply side of the parking brake switch; the second is to the supply side of the Reverse lights. These are in the Pioneer harness and both are about 12" long, so I'm guessing the connections can be accessed fairly close to the radio well in the dash.

Installing a new Pioneer radio in their 2007, and where did you pick off those two connections?

View 2 Replies

Ford Ranger / B-Series :: 2003 3.0 2WD Auto - Fuel Pump Wiring Diagram?

I'm working on a truck for a friend's mother and all of the tests that I've done point to the fuel pump. However, to make sure the pump is getting voltage past the large connector block under the cab, I would like to do a pin-out test before I pull the tank (or the bed). The pump will not run/prime in KOEO test, the relay is good, as are all of the fuses and the inertia switch.

Looking for a wiring diagram handy for this purpose? I've look all over this forum and searched quite extensively and I haven't found one for this year. Since it isn't my truck, I don't feel like purchasing a manual. I'm working on a 2003 3.0 2WD Auto.

If a wiring diagram isn't available, what colors are the wires going to the fuel pump? That way I can at least test the ground and the positive.

View 9 Replies

Ford Ranger / B-Series :: 1996 - Fuel System Malfunction - Won't Restart If Sit For Sometime?

My Ranger has been a great truck but over the last 18 months ther has been a intermitent problem with the fuel system. It would run out of fuel ( foaming spray to nothing at the fuel rail ) and if you let it sit it would start and run after 8 hrs to a couple of days. Now it is all the time. The last time I let it sit for a week in a parking lot and it started, let it warm up and turned it off to move my other truck and it would not start when I returned. I have changed the fuel pump 3 times, 2 fuel filters, relay and pressure reg. on fuel rail.

View 5 Replies

Ford Fuel System :: 1986 F150 - Fuel Coming Out Of Front Tank Filler Neck

I have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...

View 2 Replies

Ford Ranger / B-Series :: 1986 - Engine Won't Firing

i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is

View 1 Replies

Ford Ranger / B-Series :: 1986 Just Cranks But Won't Start

I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??

View 5 Replies

Ford Ranger / B-Series :: 1986 - Gas Will Not Keep Engine Running

1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed

So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.

When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........

The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.

Has been replaced within the last few months:

Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.

Has not been replaced:

Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)

With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.

View 6 Replies

Ford Ranger / B-Series :: 1986 - Bogs Down When Put Into Throttle

1986 Ranger 2.3 inline 4

I just recently bought an 86 Ranger from a friend. It had recently stopped working and had no desire to fix it. So here I am. The truck will sit in park and rev all day long, once its in drive it idols fine and moves its self down the street. The problem occurs when I apply throttle. It begins to bog down and I cannot get past 20mph. I have replaced the fuel regulator and also I took the tank down and replaced the fuel pump. The fuel filter is two months old, and the throttle response sensor is two weeks old.

View 2 Replies

Ford Ranger / B-Series :: 1986 - How To Disable Front Differential

My front diff is busted, and I mean bad.. I can barely even run the truck 5mph, and it's very loud. The diff casing is even busted. I want to just disable it to drive in 2wd. What's the easiest way to do it? It won't disable using the push button control.

Can I just remove all the locking stuff in the front wheels, so there's nothing for the axles to grab on, and manually turn the solenoid at the transfer case to shut off the front wheel axle?

View 2 Replies

Ford Ranger / B-Series :: 1986 - Stalls When Hot / Won't Restart Until Cool

I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:

-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap

I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.

View 8 Replies

Ford Fuel System :: 1986 - Losing Power While Going Uphill Only?

I have a 1986 27ft Class C RV on a E350 chassis, 460 ci with about 140,000 miles on it. I inherited it when my Dad passed. I live in the southwest and I am have trouble with it, it seems to be a fuel supply problem, I think?

It runs fine on level ground, but we tried to go to the white mountains this weekend and could not do it. On an incline the engine would start to starve for power. At times we could only drive at 25 mph! It kind of seemed like it was running out of gas, if I tried to give it more throttle it would just die or fall on its face, if I let off the pedal and gave it gas again, it would run for a bit and then do the same again. We were lucky to get it back home. I replaced the electric fuel pump (on the side of the road) during the trip, but that made no difference.

The engine ran cool the whole time! it has only one 40 gallon tank. I can find any other fuel pump on it. but don't understand all the lines going to and from the gas tank either?

I noticed there are these silver metal tubes that feed off the exhaust manifold up to a cylinder looking thing on both sides of the block. One of the tubes is broken from the ex manifold and the manifold is plugged. Not sure how this got damaged or what this parts function is but was wondering if this could be a problem ..

View 14 Replies

Ford Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire

My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr

View 5 Replies

Ford Ranger / B-Series :: 1986 - Brake Light Fuse Keeps Blowing

I've got an 86 ranger sport and I'm having trouble with the lights. The turn signals work, and ALL 4 bulbs in the back are new. The brake light fuse keeps blowing, and the fuse for the tail lights is good but they won't come on at all. I was told there was a direct short somewhere, does that sound about right? And is there a common place where they tend to short out?

View 2 Replies

Ford Fuel System :: 1986 F150 - Engine Is Running On 4 Cylinders 1 / 4 / 5 And 8

What to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.

Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.

Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.

The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.

Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.

What would my next step be? Where should i look next?

1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.

View 2 Replies

Ford Ranger / B-Series :: 1986 - Diesel Swap - Engine And Trans Combos?

I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.

View 14 Replies

Ford Ranger / B-Series :: 1986 2WD Not Running - Shift Linkage In Way To Change Starter?

But here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.

View 1 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved