Ford Ranger / B-Series :: 1985 - Water In Oil / Small Leak At The Thermostat Housing
Feb 15, 2013
So I noticed when I check the oil, there is a very small amount of water at the end of the dipstick and also water mixing with oil around the oil cap. It is not much water at all, but my first thought was head gasket. I was loosing very small amounts of coolant, but found a small leak at the thermostat housing....The truck runs fine, idles fine, no bubbles coming from the radiator at startup, no moisture from exhaust. It seems to be using more oil than normal, but I drive it 100 miles a day still and no major issues other than the perplexing bit of water and oil mixing. Could it be a tiny head gasket leak? What else would cause the water and oil to come together.
View 13 Replies
Advertisement
My '96 ranger, 4.0, auto transmission has developed a coolant leak. It is at the rear of the engine, passenger side, at or just above the bell housing. I can't quite see where it is leaking from even using an inspection mirror from on top or underneath. The engine runs great. I just finished replacing the power steering pump, ac compressor, dryer and hoses. What is back there? Freeze plug? Do I fear the worst and that the head or block warped? I may drill a hole from the passenger compartment to try and get a better view.
View 4 Replies
I have a real problem with 2000 Ranger, after changing the upper radiator hose and thermostat, I now have a pretty constant leak from the gasket between the thermostat body and engine. Appears to be something that is triggered by the thermostat opening, so whatever the leak, the thermostat is blocking it.
I've changed the gasket, cleaned the mounting surface as good as I could. Tried re-torquing the bolts, but on that score - what is the torque specs for the 2000 3.0 liter Ranger?
But ultimately, what the heck is wrong here? This should be a pretty brainless operation really. Am I tightening the connection too much and cracking the gasket? I guess that has just occurred to me, although the gasket is not as stiff as a typical fiber gasket is.
View 10 Replies
My explorer with 4.0 sohc is starting to leak fluid out of the thermostat housing. How hard is this to do and what can I expect in cost to do it myself. I dont drive this explorer but about 2 miles each way to work as I live on a military post. I have been putting it off ( just keep adding coolant and water) every couple of days. I have noticed that the engine temp doesnt not get up to half way like it use too. Maybe 1/4 of the way on the gauge now. I have always flushed coolant system very two years. It is starting to get some rush in the overflow bottle now too. Other then that she runs good and no other engine issues. She does have a 136k on her.
View 7 Replies
I set out to do a coolant flush but ran into an increasing number of problems. When I went to replace the thermostat I discovered one of the three bolts would not come out due to the inside thread on the thermostat housing being stripped. I purchased a brand new housing and O-ring.
When I reinstalled the thermostat (also Motorcraft brand) with the above O-ring and attached all the hoses I had a severe leak between the thermostat housing and the intake hose connecter. I diagnosed the problem as the O-ring slipping off of the lip or ledge inside the thermostat housing and not sealing all the way around.
The Motorcraft O-ring seemed like the diameter was too big for the interior lip of the thermostat housing because the ring would pop up on one side whenever I tried to fully seat it on the interior lip. I went to AutoZone and purchased an orange Duralast O-ring, and while it seemed to be a little smaller diameter than the Motorcraft it too slipped off when I tightened down the housing.
I have tried everything, and every time I tightened down the housing I did it very slowly and carefully doing an 1/4 turn at a time with the three bolts but still the O-ring would slip off.
View 4 Replies
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 Replies
2001 Ranger-4 Liter-169,000 Odometer Miles ... Over the past year I would get an occasional CEL indicating PO442 Leak Detected (small leak). I would simply erase it. Now it's occurring more frequently at approximately 300 odometer miles.
There must be lots a places for a small leak to develop. But, I am thinking that there might be one or two places that are somewhat common.
View 2 Replies
I'm trying to figure where the coolant leak is. Appears to originate on the driver's side front, right near the thermostat housing. Since the engine tilts back the entire drivers side is wet. The thermostat gasket appears to be OK, but it does have a lot of miles on it.
If it's not the thermostat then can coolant leak from the cross over tube. And is the cross over removable without taking off the intake. There appears to be a bolt coming up from underneath on the passenger side.
Also, does coolant flow through this plastic intake. If it does, then the leak could be some where else, if not, then it's probably the thermostat.
View 9 Replies
I had a check engine light cane on. I took it for it to get checked and they gave me this code- P0457 EVAP small leak detected. ECM has detected a large leak in the EVAP System during a system monitor test.
The paper said I had a leak in the Evap canister or hose. I took the truck to a mechanic and was told I had Bad oxygen sensors. Can Bad/Dirty oxygen sensors make this error code come up?
Exactly where the oxygen sensors are? I was told they were behind the mufflers but I didn't see any and the diagram I found was not accurate.
2002 Ford Ranger XLT v6 extra cab.
View 2 Replies
I have a coolant leak coming from I am assuming the thermostat housing or thermostat. My question is, is there a gasket behind this that I am assuming is bad or is the thermostat bad.
View 6 Replies
I have a 95 skylark 4 cylinder, i have what appears to be a coolant leak from the thermostat housing and i also have coolant mixing with my oil. Can the leak from the housing cause the coolant to mix with the oil? If not what else could be the issue?
View 3 Replies
Finally got around to replacing my Thermostat because the DIY here made it look so much easier than removing the alternator and such. Did everything exactly as described and after assembling everything with the new t-stat and O-ring I am getting a constant leak from the housing. I tried removing everything and reassembling...all the bolts are tight. Plastic housing isn't cracked and seems to be in great shape. Everything lines up properly but coolant is just running out of the bottom of the housing. Am I missing some magical trick here?
View 15 Replies
My serp belt started squealing so I pulled the thermostat housing to inspect the rubber gasket. It looked OK, but I cleaned up both surfaces and replaced with a new gasket, and put it back together. The housing was replaced just a couple months ago along with new hoses. It was not corroded and OK to reuse.
Started the truck up and saw a slowish/steady drip of red Cat ELC dripping on the driveway. Opened the hood up again and carefully inspected around the thermostat housing - no coolant is leaking there.
I did notice the same slow/steady drip coming from just behind and beneath the thermostat housing. See in pic, this is where it is dripping. One other question, what is this plug for on the side of the water pump?
View 14 Replies
2000 ford ranger, 2.5 2wd
Been having a little problem whenever it rains, the carpet on the passenger side gets soaked through and I'm not really sure where the leak is coming from. the only part of the floor that gets wet is the flat part where the passenger would put their feet, but the parts that slope up towards the dash and towards the middle of the cab stay dry. I've pulled up this part of the carpet, and the rubber grommets are intact and in good shape, and there is no rust or anything on the floorboard. from searching here it seems people have had similar problems, one thing being a leak into the seals around the third brake light above the rear window.
a couple things i should mention is that the air conditioning condenser has been broken for about two years, so could water get blocked up and leak in? since its winter here in PA i haven't used the air con since last summer though. I'm not really sure how long the leak has been happening since I've always kept a floor mat over that spot, and the carpet drys in a few days anyway.
Another thing i should mention is that the weather stripping at the bottom of the window on the drivers side door is not perfectly tight and tends to come out of place when the door is closed hard. this has been happening since i got the truck almost three years ago and a new piece was just put in a month ago (the leak had been occurring before the new piece was installed) when the truck was hit and went in for body work. possibly a drain routing to passenger floor? I should add that I'm sure it's not coolant, it has no odor and feels like water.
Might be a good idea to pull up the whole carpet on passenger's side and sit in the cab during the next storm...
View 9 Replies
One last issue with my 2000 B3000 3.0L. The leak seems to be on the left (passenger) side of the water pump very near where the bottom radiator hose connects to it. I can't find any loose bolts. It does not leak while driving the truck or soon after. It has to sit for several hours or overnight before it shows up. There are usually 3 or 4 wet spots where it drips from the water pump to the frame to the driveway. It is small enough that I only have to fill up my coolant tank every 1 or 2 months. Could this just be a small gasket leak? It's been happening for about a year or so I think. I replaced the radiator about 2 years ago. I've been expecting it to get worse or bust loose and have been checking it very often. I've never seen one not leak while running like this-has me puzzled.
View 6 Replies
I have a 85 Ranger with a 2.3L engine. I'm not getting any heat. The temperature gauge never moves off of C, except when stuck in stop & go traffic. Even then it doesn't come up much. I tried to fix this last year by putting in a new thermostat, but it didn't work.
View 6 Replies
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 Replies
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 Replies
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 Replies
My ranger has always run pretty good except for a small bit of chattering at startup which quickly went away after it warmed up. Now all of a sudden its much louder and doesnt seem to go away while driving. I read about the oil pickup tube getting blocked and not properly delivering oil and so I performed the superhuman task of dropping the oil pan to check. While I couldnt get the oil pan all the way out, I got it to where I could feel the oil pick up screen and everything seems okay. I have the valve cover off. Are the lifters adjustable? Whats the issue?
View 10 Replies
I was driving my 85 2.3 liter down the road and it died all of a sudden like and wont start back up. I took out a plug to check for spark and had someone turn it over and I touched it to the big metal part the grill connects to at the top but I got nothing. It IS getting gas. The spark plug was white as if it was really hot and rough-looking for its relative newness. I bought a new distributor cap because it was corroded, but it didnt work. They tested the ignition module at the store and its good, so I am thinking distributor?? Also, could compression issues keep it from sparking? I am a little worried it got over-heated somehow, but don't know....
View 9 Replies
