Ford Ranger / B-Series :: 1985 - Chattering At Startup Which Quickly Went Away After Warmed Up
Jun 24, 2012
My ranger has always run pretty good except for a small bit of chattering at startup which quickly went away after it warmed up. Now all of a sudden its much louder and doesnt seem to go away while driving. I read about the oil pickup tube getting blocked and not properly delivering oil and so I performed the superhuman task of dropping the oil pan to check. While I couldnt get the oil pan all the way out, I got it to where I could feel the oil pick up screen and everything seems okay. I have the valve cover off. Are the lifters adjustable? Whats the issue?
View 10 Replies
Advertisement
I have a 85 Ranger with a 2.3L engine. I'm not getting any heat. The temperature gauge never moves off of C, except when stuck in stop & go traffic. Even then it doesn't come up much. I tried to fix this last year by putting in a new thermostat, but it didn't work.
View 6 Replies
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 Replies
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 Replies
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 Replies
I was driving my 85 2.3 liter down the road and it died all of a sudden like and wont start back up. I took out a plug to check for spark and had someone turn it over and I touched it to the big metal part the grill connects to at the top but I got nothing. It IS getting gas. The spark plug was white as if it was really hot and rough-looking for its relative newness. I bought a new distributor cap because it was corroded, but it didnt work. They tested the ignition module at the store and its good, so I am thinking distributor?? Also, could compression issues keep it from sparking? I am a little worried it got over-heated somehow, but don't know....
View 9 Replies
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 Replies
So 85 ranger with 2.3l and A4ld. I can manually shift to get first and 2nd. When i look at the vaccume diagram it shows these 2 blocks on the tranny,one box is connected to the next with a vac line. The other box has 2 lines, one goes to the main vaccume block on the intake and the other T's into a small capped off canister and the egr. I can only find one place for a vac line and its on the pasgr side of the tranny... Where is the block that the egr line connects too located? Its not on the tranny as far as i can tell.
View 2 Replies
When I turn on my heater full blast the most god awful squealing commences. Where to start spraying the grease?
View 10 Replies
So I noticed when I check the oil, there is a very small amount of water at the end of the dipstick and also water mixing with oil around the oil cap. It is not much water at all, but my first thought was head gasket. I was loosing very small amounts of coolant, but found a small leak at the thermostat housing....The truck runs fine, idles fine, no bubbles coming from the radiator at startup, no moisture from exhaust. It seems to be using more oil than normal, but I drive it 100 miles a day still and no major issues other than the perplexing bit of water and oil mixing. Could it be a tiny head gasket leak? What else would cause the water and oil to come together.
View 13 Replies
85 ford ranger 2.3 efi .. My brake lights still aren't coming on. According to the Haynes manual, the wire that runs from the stop light fuse goes from there to the hazard flasher and then to the brake light switch. Since I have checked everything else, is it possible that the hazards are causing a break in the connection?
View 4 Replies
So I did alot of electrical work on this truck but never had any problems with the brake lights, now they dont work and the fuse blows every time you pop one in.
View 1 Replies
I have a 95 Ranger that when warmed up completely will buck when I let off of the gas. It is a 5 speed and this problem really only happens in 3rd gear and also have noticed it doesn't happen in 4WD. When the engine is cold and I am driving and let off the gas, the truck coasts smooth as silk and as it warms up, there becomes a louder thump when the gas is let off.
It will not do it all the time and it really only happens in third gear at low RPM's coming to a stop. I can give it gas and it picks right back up normally, so I doubt it is a misfire. Also since the truck is a 95 I do not have any CEL indicators, nor is there even a CEL light built into the dash in the truck. It isn't a huge issue because I am used to it and can drive it accordingly without having a problem.
View 13 Replies
85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
View 14 Replies
1985 2.3L... New fuel pump And fuel pump relay, problem was happening before new parts. the wires at inertia switch continue to get hot switch has been removed. The heat continues to under the hood where there is some so rt of connecting link and heat stops.what the is this link for, it doesn't look like A fusible link?? Saw a similar post here about a fuel pump shutting down and wires getting hot. Same problem.
View 9 Replies
Ok, I replaced the head gaskets on this truck a couple years back and now I am having symptoms similar to the ones I was having then. I am not entirely convinced that this is what is wrong however.
Symptoms:
Truck was idling rough until it warmed up
Truck takes forever to warm up or simply does not warm up
If/when it warms up it operates at higher than normal temp/almost overheats(it hasn't overheated yet)
Heater blows very cold air
White smoke(has been cold outside so not sure if due to temp or coolant)
Overflow bubbled when I shut the truck off, but it has only happened once so far
I am kind of at a loss, but like I said am suspicious of the head gaskets.
View 8 Replies
I have a 1987 ranger 2.9 V6. Have a intermittent miss @ idle when warmed up. What is the proper way to pull the codes from the computer, i,st something about counting flashes or lights...
View 6 Replies
'86 Ranger, 2.3L, Automatic transmission.
Been having a sputtering/rough running situation once warmed up, replaced every so often with open loop smooth running. Lately, have had several occasions where the truck stalls and will not restart after a hard right turn (fuel pump powers up, tho) After 30 or so minutes of repose, truck will restart and run.
Recent History:
During the last 1-1/2 years, had cylinder head rebuilt and reinstalled. Had to run it all winter w/o EGR tube attached because of bad fitting at exhaust manifold. Replaced the fitting last spring and replaced cat back exhaust system. Had manifold hole plugged with pipe plug all winter. Have had a diagnosis of poor compression in the past, have not rechecked compression since head rebuild, but did have a noticable increase in power.
Have checked base ignition timing and it is correct. Valve timing appears to be as it should be. Have not had the opportunity to check for spark during one of the breakdowns, since I had no tools and it was night time.
The codes:
Early in Fall, got 14, 21, 24, 34. The 14 particularly interested me, as it suggests ignition problems.
Just before pulling the distributor, I checked codes again; 14 had disappeared as did 34 (EGR issues I resolved above) but I still got 21 (coolant temp out of range) and 41 (no HEGO switch) So I left the distributor alone and replace the HEGO sensor and cleared codes.
Last code check, just got 21(coolant temp sensor voltage out of range) and 24(air charge or Vane air temp voltage out of range) There is very little heat on cold days, full radiator and I've "burped" the cylinder head on an incline more than once chasing trapped air.
I'm suspicious of the TIF module, since the stalling is after warm up and self corrects. It was replaced once perhaps 12 years ago.
View 3 Replies
I bought a 1990 ranger with only 38000 miles on it from a online auction from boing aircraft. it never left the flight line and never even had a title. I picked it up from the airport and found out that it didn't have AC like they said, I was a little ticked but that isn't the main problem. When I drive it and it gets warmed up it leaks Tranny fluid from the front of the transmission. The engine does not overheat. It is a 4 cyl AOD automatic with a real thin radiator and a transmission cooler. Without AC the truck isn't the good deal I thought I was getting, and with a bad tranny this is becoming a big OOPS. Why this is happening?
View 3 Replies
On startup, hot or cold, I get an initial high idle, up to around 1800 rpm's. This happens immediately when engine starts, and then idles right down. This has done this since new in '04. Dealer at that time said it was normal and not to worry. It's always made me wonder, but I trusted the dealer. Ya, not always smart.
After 92k miles. Engine runs fine otherwise, but I don't really care for grabbing a bunch of rpm's on any engine without having the oil pressure up to normal.
A few weeks ago, I started it up, and some yahoo said he knew I drove big trucks by the way I started my Ranger. That was one of those times. I'm thinking IAC is wide open maybe?
View 3 Replies
I have a 98 Ranger SuperCab XLT 4WD 4.0 Auto. Occasionally, especially when it has been sitting for more than 3 days, it shakes for maybe 30 seconds on startup. It smooths out gradually after that, maybe 15 sec. to normal smoothness. It seems like it is firing on all cylinders and is more like something out of balance.
Never does it when sits less than 2 days. When it happens, the longer it sits the worse it shakes.
View 3 Replies
