Ford Ranger / B-Series :: 1984 2.8L Started Then Revved Up High And Shut Off Immediately
Jun 29, 2012
I just rebuilt the carb on the truck, it has the 2.8L, and when I went go go start it, it cranked for awhile until fuel filled the bowl, then it started and revved up high, I shut it off immediately and it turns out the throttle linkage was binding for some reason, I fixed that but now it wont restart.
I was cranking it for a while and gas started spewing out of the top, so I took the top of the carb off and reset the float height and now it doesn't spew gas.
I pulled the plugs and checked for spark and it's a really bright blue spark. I'm thinking it's just flooded, lots of gas on the plugs? I'm just waiting for it to clear out now and trying to brain storm what could be wrong.
View 14 Replies
Advertisement
Got a 1986 Ranger 2.3 EFI 5 speed that I have owned since it was almost new and will never let it go. 290,000 mls and still running strong "except". Noticed the last couple of months that when I start it cold it fires right off. If I start it hot it always takes 3 tries and always goes on the third try except....on occasion it will not start at all. It is random and after I let it cool a bit (about 30 min) it will start. Over the years I have replace many of the fuel system components (fuel tank pump, high press. pump, inline filter and canister filter, fuel press regulator) but wondering what else might be the problem.
I put a pressure tester on it the other day and when I selected the key to start the pump would spool up to build pressure and shut off. The press gauge would register that but the pressure would immediately go back to zero. After start up it would hold a constant 30psi at all rpm,s. Shut the engine off and pressure drops right down to zero. Shouldn't the system hold pressure for at least a while after shut down? Could this be the problem with my sluggish starts? What would be the normal fuel pressure? Can't seem to find it in my Haynes manual. Once running it runs great.
View 6 Replies
So I turned off my truck the other day, got out, and it started again on its own. Confused, I looked in my hand to see my key. I got back in, and tapped the brake thinking the command start had engaged, even though I did not have the remote with me. It continued to run. So I put the key back in the ignition, turned it to ON and back OFF. It still ran. I had to run inside for a half a minute so I left it running.
Came back and drove away with no issues. When I stopped again about 2 minutes later and shifted to PARK, the starter engaged making it's terrible 'hey stupid, I'm already running' sound. I tried shutting it OFF quickly but it still ran and made it's skinning crawling noise. So I quickly shifted back to DRIVE. All the gears worked fine but PARK and NEUTRAL had the starter engaging. I also could not shut the truck off from DRIVE as the key would not turn.
I drove over to a local garage and called them from the truck as I was effectively trapped in the truck with my foot on the brake, unable to shift to PARK or turn it OFF. No supporting staff. So I drove back to work where I had a co-worker remove the battery cable at which point I was able to shift to PARK and turn OFF the truck. I let it sit like that for about 10 minutes and haven't had a problem since.
What happened?? And for the record I can put gas in the tank and changed my own oil, but that is the extent of my vehicle knowledge.
View 14 Replies
My friends 2004 6.0 f250 has 280000 miles on it and it runs perfect "did" until I tuned it with my sct tuner to run a looney tune so he could see what it was like. The truck started he revved it up to 3'000 rpm then when it returned to idle it acted like someone shut the key off. The high pressure oil system is new and has 700 psi and the icp is good also the ipr. The truck Is not getting any fuel at all, no smoke from cranking at all. It is returned to stock and is still being difficult. It has fuel I checked the upper fuel filter, it has enough oil, and it also has a good motor just don't fire. Why?
View 3 Replies
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 Replies
Just recently my 2003 3.0 Ranger has started to rev high between shifts. With the clutch in the it will continue to rev high for 8 to 10 seconds. Where should I begin to look to correct this problem?
View 4 Replies
I didn't really know where else to turn (no pun intended) every time I turn my wheel to the right the truck sputters out and dies, i checked the ignition switch, tightened her up and shes still killing the engine when i turn right. All other power remains on stereo, car charger etc. its not so bad on continuous turns i can just pop the clutch but for stopping and turning its a huge issue. Why turning left is fine but right kills the engine..wondering if maybe the prongs on the ignition switch may be bad?
View 7 Replies
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
View 6 Replies
I just picked up a 1984 ford ranger long box 2 wheel drive w/ 2.0 l and carburetor for our daughter whom is just 15. it has a whopping 19,000 actual on it! It was my wife's grandma's farm truck - ordered it new from dear born. Any way, fuel gauge is pegged at empty and they had a new float assy put in about 5 years ago, but it is dead now, it doesn't appear that this sender is avail any longer. What part might fit in there and or what do i have to do to maintain the original gauge in the cluster but have a working sender to talk to it? is there another unit that goes in the tank that i can modify the signal out to read right with the built in gauge? There can't be too many different ones out there is there?
View 8 Replies
I've got a '84 ranger that idles super fast for about 30 minutes after a cold start. The truck has been in the family since new and has done it since day one. I am wondering if replacing the electric choke or choke pull down would work. I've got a electric choke replacement but the cover place looks to be attached with rivets not screws. How to remove the choke?
View 3 Replies
I have a 1984 Ford Ranger 4x4 with 2.8L V6, carburetor number E37E-AEA. The accelerator pump diaphragm is perforated.
Small holes are visible when I hold it up to a light. Is this part available anywhere? Is it included in these carb repair kits that I see on a lot of auto parts sites? The sites don't list the contents of their "kits."
View 2 Replies
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 Replies
So, a few day i bought an 84 Ranger and even since have not been able to figure out what the hell is wrong with the brakes. I know it's not the brake booster for starters. Because, i went to Auto Zone and picked up a new one and when i took the old one off (before i had put the new one on as well) i tried to see if the brake pedal would now move freely and it won't. It is still very stiff and squeaks when you push it down. i then to get it to return have to pull it up with my foot... What it might be? the WD-40 failed here as well.
View 3 Replies
It's an oldie, 1984, but so far still kicking. 6 cyl 2.8, carb. I took a little couple hundred mile trip a few weeks ago. Rolled back into town no problems.
A few days later I took a ride and the ranger would stall when approaching a stop sign or light. I would hold the pedal down a little to keep it running but it sounded like it wanted to die if I didn't feather the pedal to rev a bit.
I drove a few days later, as I was going down the neighborhood road(25 mph), it acted like it wanted to just die. I mashed the pedal and it had no effect. It didn't stall and eventually I could rev the engine to continue.
It continues to do the same, then will all of a sudden take off like there was never a problem. If/when it does stall again, it can be hard to start until it does start and off I go again like there was never a problem. Other times, it will idle.
Another note: Sometimes when I go to start the engine it will stutter, intermittently turnover. It has done the same thing while actually driving, kind of a jerking deal.
Fuel filter, fuel pump, electrical? I'm going to first check/replace the fuel filter tomorrow.
View 10 Replies
Tried changing fuel filters on my 2008 F350 diesel. Tried primary - open drain - no tool to remove cap, closed drain. Removed top cap, replaced filter.
Started but immediately shut down. Did this twice. Put old filter back in - still no start. Wrench code light on.
View 9 Replies
It's a 2012 Corolla. I disconnected the battery and the 2 grounds where the fender mounts in the front. I did this to do some body repairs. When I reconnected everything, the car started, but immediately shut off. What is wrong? Is it a computer issue where it needs to relearn?
View 5 Replies
1996' Ranger with 183,000 miles. 2.3 cyl., Automatic, XLT
When I am driving and get to the 35 to 60 mph range, my trucks transmission wants to upshift, then immediately downshift to the gear it just left. It goes back and forth like this till I get where I am going, or after about 10 miles it will stop doing it. I checked the transmission fluid, and it is full and still pink.
I took it to Advanced Auto, and it blew a code of ECL Bank 1 I believe. I looked around the 'net and I think it came out to be the front O2 sensor may be bad/going bad.
Last week while it was warm enough I was driving with the rear window open, and noticed the faint smell of Rotten Eggs (this has been the only time though). Today I drove about 50 miles and basically used a quarter of a tank of gas. I am wondering if the catalytic convertor may also be going bad?
View 9 Replies
I was messing with the battery in my 200 Ford Ranger the other day and must of arc something. I know this because after plugging my battery back up my radio fuse was blown and my alternator was killed. I replaces the radio fuse, that works now, and got a new remanufacted alternator (tested mine at Advance it was dead). I installed it and nothing changed. The battery still wasn't charging. I know the battery is good because I tested it at Advance Auto. I took the alternator back and the shop replaced it with another remanufacted one. Same thing, installed it and the battery doesn't charge.
This time I took the alt back off and had it tested at Advance. The alt was dead. So I don't know if the part store gave me TWO bad alternators or if my truck is killing them. I find it hard to believe it could kill them immediately but my automotive knowledge is not that vast. I took the second (third counting my original) dead alternator back and they gave me a brand new one no extra charge. So I don't want to put a brand new alt in my truck and it kill this one too because I doubt they will give me a fourth one. What is going on? Could it just be as simple as I got two bad eggs?
View 9 Replies
I have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 Replies
I have a 92 ford ranger. About a year ago it shut down on me as I was pulling out of a parking lot. I replaced the Cam sensor which IS NOT located on the engine block by the fire wall. It is located on the front of the engine just above the primary cam which is just above the crank shaft and its sensor. It fired right up.
Then the oil pump went out and I just replaced it the other day and the pressure gauge/needle went past the half way mark even at idle. I drove around a bit, maybe 10 miles, then got in it to go to the gas station and got about 50ft from the house and it just died again and will not crank back up.
I am thinking its that darn cam sensor again. But, just like the oil pump was, it's a pain to get to and replace. How to test it. Oh, it is a 2.3 4 cyl. double overhead cam. I do have fuel pressure, I checked that already.
View 14 Replies
1987, 2.9 ... I got all my wiring repaired and replaced both the intank pump and the high pressure pump, for a few days it would fire right up as soon as you hit the key but it had a miss (the pumps shut off after a second or two with the key on "RUN"). I tore the throttle body off and cleaned all the carbon out of it, when I put the throttle body back on I noticed that the engine to body ground was loose so I ran a new piece of 4ga from the intake manifold bolt to one of the master cylinder bolts.
After I did this I went to start the truck and no go, the fuel pump turns on with the key but then it wont shut back off until you turn the key off. if you try and start the truck it will crank but wont fire, after about a half hour of cycling the key and cranking it will start to put a little bit then a few tries later it will start but sounds rough when it first fires. I thought it may be a stuck injector so I ran some cleaner through the Schrader valve on the rail. Still have nothing, both pumps do run but still don't shut off after a few seconds like they should and now it wont even try to start.
View 12 Replies
