Ford Ranger / B-Series :: 1957 - Driver Side Seat Reclining Mechanism Broke
Dec 17, 2012
I bought a set of Ranger seats for my 1957 Ford project. My question is the drivers side seat reclining mechanism is broke. I believe the seats are out of an STX or sport model, they have a slide out bolster and power lumbar and side bolsters.
Where to get a replacement mechanism. The mechanism works the handle is busted off. It is from an extra cab so the handle is a two way for the driver and or if anyone in the back wanted to use it. I think they may be from a 1992, only say this because I had one backin the day with these kind of seats.
View 4 Replies
Advertisement
My driver seat has started moving on its own, sliding back and reclining. 1 have a 2008 Azera, 45,000 mi
View 4 Replies
I have a 1987 Ford Ranger 2.3L, it's the truck I learned to drive in (stick at 13yo) and the 1st car I crashed too... So now this baby is almost 30 years old and recently had a minor restoration...
Engine was pulled out and all gaskets were changed, spark plugs, wire... All that stuff... It has been running pretty good, however last week a water line broke on the Left side near the spark plugs (if you are looking at the truck)
Since then It has absolutely Zero power. The slightest hill and even when pedal to the floor will lose power. Yesterday went from the start of a hill at 60mph in 4th to 20mph in 2nd because it didn't have the guts to go 1/3 mile uphill... I checked everything I could, and my brother took it to the exhaust guy who made a small hole on the Catalytic Converter and said it was good, but he could tell it was running too rich...
I replaced some of the vacuum lines last night, I found a lose one on the fuel pressure regulator (I think that's what it is, Its towards the engine firewall on top).
Idles beautifully, drives great, no rough shifting, pinging or knocking, no misfires. So that's what has me stumped... Runs great but just no power... Also before water line broke it was running fine with power...
1987 Ford Ranger
2.3L FI
5sp manual, Rwd
View 11 Replies
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
View 4 Replies
I've got an 08' Ranger FX4. Recently I had the drivers-side headlight go out. Today I replaced the light, and while I was there, I decided to check every bulb on the truck. Everything else works, but I noticed the 2 factory "foglights" will not come on. This is a fairly recent development, because I use those lights quite often.
Even thought they don't cast a huge amount of light, here in the Vancouver area, winters are dark & rainy, so I think 4 points of light as opposed to 2 points is a benefit. To activate those lights, you pull on the headlight selector switch. Do those lights have their own dedicated circuit with fuse? Or does this sound like a switch problem?
View 14 Replies
My '99 Explorer XL has the standard bucket seats. After having two owners (first one '99-09, then me '09-present) climbing in and out over 11 years and 95,000 miles, the driver's seat has broken down on the left side near the reclining lever. Every time I go around a right turn, I feel like Im going to tip over against the driver's door. Is there a replacement cushion for these Explorers?
View 3 Replies
I've been having to add a quart of oil between every 3,000 mile oil change. This is a used 2000 2.5L motor now with about 150,000 miles on it and 317,000 on my truck. I notice the oil is coming from somewhere on the side maybe in a few places. I think the oil plug is dripping a little. I'm going to try an OEM Ford plug because I've changed them several times with aftermarket plugs and they never seal right. I thought it might be the oil pan gasket but it doesn't really look wet around the flange all the way around.
Then I checked higher up thinking it maybe the valve cover gasket which has been replaced and it's drive around the cover. I noticed under the power steering pump bracket it's all wet with oil. It's not the power steering, I've never had to add to it. It appears to be in the middle under the intake. I didn't see anything from the pressure switch. It looks like it's mostly around the pcv valve box. Is there a gasket that leaks there? Or anywhere else that is common to leak? I fixed my transmission pan gasket leak which cleared up some of the mess on the bottom. How hard is it to change that pcv valve box? They call it a crankcase vapor separator where the pcv valve goes.
View 10 Replies
I have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.
I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.
The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?
If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.
This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.
View 9 Replies
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 Replies
1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.
View 14 Replies
I'm normally in the bullnose section, but recently started working on my father-in-law's 96 ford ranger. He wanted me to replace the front rotors.
I replaced the passenger side without a hitch, but when I went to replace the driver's side, I noticed the cotter pin and castle nut were missing. A nail was in the cotter pin's place. I backed off the spindle nut and found that the threads were eaten up, as was most of the spindle with various gouges and nicks.
1996 Ford Ranger XLT 2.3 ......
View 11 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?
View 3 Replies
Bought a 2002 ranger with a four liter in it. Didn't notice until actually going off-road there is something wrong with the four wheel drive. In 4 high it will drive good for a random distance then a loud bang, pop, comes from what feels like it's the driver front tire. The faster you're moving the worse it is. It's not consistent at all.
Replaced the transfer case shift motor and both CV axles. Still does it. Walked next to the truck while it's moving and the front tires look like something is in a bind and it's causing the bang. Beating my head against the wall at this point.
On a side note it has something wrong with the tranny. Taking off it feels like someone bumped the rear, and after about twenty minutes of driving od light starts blinking and it shifts hard from first to second. Kill it, cures that specific problem just not the takeoff problem. Not sure if this is all related. Pulled the pan and refilled with as much fluid as came out. Which was a dark red. Still having same issues.
View 5 Replies
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
View 1 Replies
I have an 03 ranger and my driver side window will not roll down... My pass side rolls down just fine...when I push the down button all I get is a clicking noise out of what seems to be a little black box underneath the driver side dash and I can actually physically feel the clicking along with hearing it... When I push up on the button I get no noise or anything... this might be the motor...the regulator...or the actual switch?
View 1 Replies
So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.
View 3 Replies
Checked icm and is good, replaced coil and still no spark. Issues be gan when about 700 miles ago rotor button broke while driving??? Replaced button cap wires and plugs. Engine fired right up. Ran 700 miles and rotor button broke for 2nd time. This time replaced and will turn over but not crank. That's when I checked icm and changed coil. what should i check now?? 1993 Ranger 3.0 ... Truck has 199,800 miles. Top end was redone at 140,000.
View 10 Replies
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 Replies
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 Replies
2001 Ranger 4 liter 4 door My driver side window goes up and the electric motor does not stop running when the window reaches its normal upper position. Instead it goes bang-bang-bang until I take my finger off of the switch. I'm guessing there is a limit switch that should disconnect the motor but has failed. The bang-bang (again I'm guessing) probably is some sort of a spring loaded torque limiter to protect the motor. Other than that, the window goes up & down as it normally should. I have no problem digging into the door, except with the window, door lock and outside mirror switches, I don't have a clue regarding how to get the inside door panel off. I know to disconnect the battery 1st.
View 1 Replies
