Ford Ranger / B-Series :: 1940 Pickup - Upgrading To Power Brakes
Mar 31, 2013
I have my 1940 Ford pickup on an 86 Ranger chassis. I'm finally to the point where I can drive the truck a little (still not running right) and I'm thinking about upgrading to power brakes. I have used the entire braking system from the Ranger in this build. What's involved in upgrading? Right now, there's a standard Ranger master cylinder hung on the firewall and attached to a Ranger pedal hanger assembly on the other side of the firewall, so I have all Ford parts to interface with. Also, what is the diameter of the booster and how deep is it from front to back and will the upgrade require a different master cylinder?
View 3 Replies
Advertisement
I've got a 99 Ranger. A month or so ago, it started to be a little hard to start. It would turn over, but not fully start unless I gave it a little gas. This did not happen all the time, primarily it happened after it had sat all day when I left work. Not long after that started, my check engine light came on. The codes were for a lean mix as reported from the 02 sensors. Before I could dig any further, it just wouldn't start at all one evening. This was after I had driven it for 30min and then parked it for an hour or less. But this time it was different in that the solenoid would just click, but that was it, like it didn't have enough power to turn over. I took the battery to have it tested and it had been severely discharged.
I got a new battery as that one had reached it's limits. Put it in and the truck started right up no problem. A few days later it started acting up again like it had originally, I had to give it some gas to get started. I had the alternator/starter checked, both were fine. A day later, it got so bad that I had to shift to N and keep giving it fuel anytime I stopped the truck. I had to do this all the way to and from work. Now this morning I go out and it starts right up, no issues, no dying at idle and didn't have bit of problem coming in. Initially we thought it must be a fuel pump, but then I can't explain why it worked fine this morning. I changed the fuel filter less than 2 years ago, so I wouldn't think it would require changing already. Wondering if there's a sensor issue, one that calls for appropriate amount of fuel?
View 2 Replies
I have a 10 inch lift and 37's on my excursion 2000 7.3l. I need to upgrade the breaks, the tires make it very hard to stop.
View 1 Replies
I had to replace the tie rods in my mazda b2300 and the mechanic also replaced the brake pads.
Now when I drive, I can hear the pump for the brake fluid going on and off when I'm not even using the brakes and the ABS goes on a lot too.
He tried resetting the computer by unplugging the battery for a bit but it's still doing it.
View 2 Replies
Little back story, truck sat up for 2 years. Had 1/2 tank of gas in it that time. I had to do a complete motor swap. I been driving for past couple of days. Had it stall on me while I was waiting on wife to come out of store. Thought it was just bad gas. Today I was heading to town and had to slam on brakes and it started to stall again. It shut off. I cranked it back up and it runs fine till I start slowing down. then it wants to die.
I can keep my foot on gas petal and little and it will stay running. I got to where I was heading and put it in park and it idled fine for a few seconds and then I could hear a whine from the fuel tank. Sounds like the fuel was having a hard time, like it was fighting the pressure build.
Thing is It cranks right back up and drives fine as long as I dont come to quick stop or set idling for a few seconds. I can hear the pump straining, so I am assuming that when I keep my foot on gas a little the pressure is staying lower and not as much is being bypassed and the pump is fine. I think the pump is on its way out but wanted to hear what yall think.
I do have a brand new IAC valve that I bought and did not get a chance to use on the blown motor.
View 10 Replies
I tried to explain this to a garage in January with no luck. When it is raining I hit my brakes and my truck jerks like whiplash. Softly hitting brakes doesn't do it, normally hitting them does it (only in the rain), I had some welding done after I went to the garage.... They fixed the front passenger side now it feels like it is under me and it is now doing it when I brake in reverse too... I bought it October 2012 and it was safety inspected until October 2014. Trying to decide if it is worth keeping. I want to keep it but when I go to a garage they see dollar signs. It only acts up when it's raining. And I had the welding done in January and it was fine, until I got new tires last week.
View 12 Replies
Received the truck, 1989 Ranger XLT long bed single cab from my mom. It had been used by my younger brothers for some years, and then sat at mom's for a couple years.
It needed new front brakes badly, so replaced rotors, and pads. No unexpected problems there.
Looked at replacing the rear. Both adjuster cables were initially broken, so they obviously weren't adjusting, or braking. Replaced with a hardware kit, and shoes, and drums. Its the 9" drums, BTW.
Still not actually braking. I can tell this, when at a stop sign in the winter, with the brake pedal held down, and the backs will still spin, with the tranny in D. Even on gravel or grass, this'll happen.
One shop told me this is because the axle seals are leaking. THey've never leaked badly, and the axle fluid isn't low, by and shade of the imagination. Also, this theory falls apart, when the parking brake works just fine, right? Its just hydraulically that they don't work.
I've since replaced the wheel cylinders, the brake line from the frame to the rear axle, and the master cylinder. No change. Bleeding them doesn't seem to be a problem; i.e. no lack of or little fluid witnessed, it seem fine.
Also have bypassed the RABS valve for about a year or so, and its made no difference. Last fall I pulled the drums off, and manually adjusted them, and it didn't seem much better either.
View 11 Replies
On deceleration with the brakes (not coast to slow) I get a growling. Sometimes a bit worse than others. Seems to get worse coming up to about 20mph from speed. No other time. I was thinking front wheel bearings as the load up from deceleration. But I just jacked it up and could not find anything that felt or sounded wrong. No play or grind or "bad" feelings in either of the fronts. Front end recently rebuilt, new tires too.
View 9 Replies
I have a 2007 ranger and when applying the brakes i get a vibration, I think it may be in the rear of the truck but it is hard to tell.
View 2 Replies
All I did was take wheel off to tap a stud and I saw the inboard pad shim came off. So I removed the shim and reinstalled everything and the wheel is severely pulling to the right. Yesterday I took the caliper off but did not take off hose, cleaned slide pins and lubricated with anti seize. Still pulling to right bad. Don't hear any squealing or grinding. But pass side wheel is definitely hotter than drivers side. One mechanic said he thinks it would be a bad hose before replacing caliper. What could it be?
View 8 Replies
My manual 5 speed 99' 2WD 2.5L Ranger is starting to have some small problems here and there. My main concern is when I start the vehicle sometimes, there is no idle. The vehicle will turn over and if I do not hold the gas pedal down it will die immediately after about 2 seconds.
If I hold the gas down so the RPM's stay up (Around 700 RPM's or so, something just a little above 0 to keep it from dying) after about a minute, sometimes few minutes the idle will kick in and I do not need to hold my foot on the gas pedal to keep the truck from dying.
This is about all I know from the problem besides that it does not matter how long my truck is sitting. For example, my truck was sitting for 5 days and I came home and started it up just fine, but after I drove it a few minutes later and stopped driving, when I went to drive it about an hour later the symptoms came back again.
Also, My brakes are acting a little funny. I went through when I first got the vehicle and bled the brakes, took the front rotors in to auto zone or another shop and had them fixed up, and new brake pads. Sometimes when I first start driving the brakes are extremely sensitive, to the point where I apply a little bit of pressure and my truck will start skidding. This goes away after driving for a little bit though.
View 1 Replies
I just had new shoes, hardware, wheel cylinders, drums, leaf springs, rear shocks, and shackles put on. The brakes were done about 4 or 5 months ago and the springs and shocks just a few weeks ago. The rear brakes were locking up after I had the work done, but I thought they were just too tight. I loosened them a little but it only worked a little.
Now it's starting to lock up pretty much every time I apply the brakes. The ABS kicks on and the rear tires skid. I took the drums off today and didn't see any leakage or anything out of the ordinary. They weren't too tight and I readjusted them but they weren't out of adjustment much if at all. I looked at the Ford symptom chart and it says for brakes that lock up easily there could be sticking or binding components. I didn't see any. Then it says check parking brake components.
Now I see they didn't hook up the equalizer bracket that goes to the front leaf spring hanger when they changed my springs so I assume thats why my parking brake pedal goes to the floor. Then it says check the shoes and linings, which are fine. The last thing it says is to check the fluid control valve. Which I'm guessing is the prop valve.
The only way to check it according to Ford is swap it for a known working valve. One person told me that it could actually be a bad brake booster check valve. Is that possible? Anything else that's common? It's got 272,000 miles on the frame but everything's been changed that typically wears out at least once.
View 9 Replies
I recently changed the front pads and rotors on my 2002 Ford Ranger 2wd and I'm having some troubles now. Occasionally when I'm pulling up to stop lights toward the end of my braking i can feel them cut out and the ABS kicks on. It's a very intermittent problem, and it only happens at low speeds. When I try to induce the fault it never happens, it only seems to after an extended period of braking going less than 10 mph. I'm very confused, and I was thinking about changing out my calipers unless know what might be happening.
View 1 Replies
I have a 2004 Ranger 4x4, 4.0, auto and have trouble with the back brakes howling, locking up and generally driving me nuts. I've replaced the drums, shoes, cylinders, emergency brake cables and all the hardware. We've bled all 4 numerous times, blown out the lines, looked for leaks and done all we can think of. What am I missing?
View 1 Replies
I have a '99 Ford Ranger XLT 2WD. I've been having this problem with my rear brakes locking up on me while slowing down and pressing the pedal to stop the forward movement. There are four components which could cause the problem. My OEM Ranger Repair Manual suggested to replace the Proportional Control Valve which I did however that did not correct the problem. I don't have the Brake nor the ABS Warning light coming on and they check out OK during the start up. I have no problems braking from any speed except when coming to a stop. I inspected my front disk and the rear shoe brakes and they seemed to look OK. The other components which could cause the problem are the Control Module, RABS valve and the Speed Sensor. My question is: If any of these components malfunction, shouldn't the ABS Warning Light come on?
View 2 Replies
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 Replies
I have a 1990 4x4 ford Ranger, the little truck was purchased in early 2008 as a work truck but has ended up becoming my main vehicle, it has been a good truck for the most part but know I am having some brake issues, well have been having for some time but they seem to come and go. Usually it happens when I have to hit the brakes hard, the rear brakes lock up, I replaced the master cylinder months ago and thought that fixed it, then a month later it happened again. The last time it happened was friday, the time before that was in march 09'.
I have searched this online and found numerous try this but the original poster never comes back to say if the problem is fixed or what fixed it. My ABS light DOES NOT come on when this happens, it does function properly, it illuminates when the key is turned on then goes off. My parking brake no longer works either but I think that is from me "driving thru" the locked up rear brakes. I plan on replacign both drums and shoes within the next week but would like an option to repair the locking up issue.
View 14 Replies
Odd thing on the 97' Ranger that showed up today. I was backing out of the spot at the local Shell station, (on an incline) and the pedal went to the floor. Never happened before. I pumped the brakes a few times, and they came back. On down the street, slowing for the stop sign, pedal went to the floor again.
Not throwing codes, fluid levels are good, only seems to happen at lower speeds/idle. Sometimes pumping brings the brakes back, sometimes they come back all of a sudden.
I can hear a "sucking" kind of noise coming from where the pedal connects to the booster, up under the dash. I looked at it, and nothing *appears* to be broken.
It almost feels like the pads are against the discs, and the pistons/calipers have to reach for them before the brakes apply. (If that makes any sense)
There should be about 50% of life left on the pads, but i haven't pulled the fronts wheels yet to look.
View 11 Replies
For about 6 months my 95 ford ranger 2WD 4 cylinder pick up has occasionally gone into "over drive" when it is not in gear the idle will get crazy high, like one of those party toys that yo blow into and it spins an makes noise. Once put into gear it calms down but it has more forward motion without gas than before. If it gets really bad at stop lights I will turn it off and turn it back on. It may still do it when I turn it back on but by then I will be putting it in gear. When it is in this condition and I turn it off it takes longer to turn off, like it is winding down.
I would say that this happens every 4th time it is drive, sometimes less sometimes more. There seems to be no rhythm. I took it to an electrical specialist and they could not find anything, and last week the check engine light came on so I took it to our normal mechanic. They did a test and found that the engine speed limiter had been reached which was why the check engine light came on and also pretty scary. The diagnostic codes were P0500 and P1270. I am worried 1. that this is making the care unsafe to drive even though it seems like we can manage it to a degree and 2. that is is doing damage to the car by putting it in such a hyper work mode.
View 2 Replies
I have been thru everything i can think of except the main ECU on the ranger.
I've replaced the starter as well as the starter solenoid also the ignition switch.
What is happening is there is no power after the main wire to the solenoid from the battery. it doesn't power up anything. I've checked the fusible link and it appears intact. with a test light i can see that i have no power from the ignition itself i guess to tell the solenoid to work. i have noticed that the ignition cylinder is a little loose but what can cause there to be no power at all?
Could it be a bad solenoid?
View 2 Replies
I just was given this truck the fuel pump was wired directly to the battery I ran new wire to a new relay to fuel pump using a toggle switch to turn the pump on. Now I'm getting no power to the fuel injectors does the pump relay also send power to the injectors.
View 7 Replies
