I have a problem. I have a nylon return fuel line that is SHOOTING out fuel at the quick connect at the fuel pump. See video: [URL] ....
How do I repair? I think the o-rings in the quick connect went bad. I'm thinking to dip the connector in hot water to soften up the nylon, take the old connector off, and put a new connector on. What size connector I need?
I have a 1989 Ford mustang 4 cylinder. The return line tofuel tank is leaking. I am wondering if I need to treat the return line as a "high Pressure line" or if I can repair with regular rubber fuel line and hose clamps.
View 4 RepliesNew to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
My HPOP was leaking so I pulled it our last weekend along with the fuel bowl and put all new seals in. All my previous leaks are sealed but now this stupid fuel bowl is being a major PIA.
The return line coming off the FPR will not stop leaking! It was slowly dripping when I first replaced the bowl and I thought the leak was between the fuel bowl and FPR housing. I ordered new rings and put it back together.... still leaking.
I wrapped a towel around the fuel fitting and realized that is were the leak is actually coming from. I went to the parker store today and got 3 new 60VL5 sleeves. The first one tore while sling over the fuel line (I was using 2cycle oil as lubricate). The second one leaked even worse.
In a desperate attempt to stop the leak, I slid the sleeve onto the fuel line as far back as it would go. I inserted the fuel line into the bowl and then put a thin coat of rtv on the exposed fuel line. I slid the sleeve over the rtv and then put a light coat of the outside of the sleeve. I tightened the nut up and am waiting for things to dry before trying again.
Why is this fitting giving me such a hard time? I've pulled the FPR housing and it is not cracked so I don't know what the deal is.
Someone stopped by the shop today with a problem with the power steering leaking. I checked it out and the return line from the rack to the pump is rusted through and needs to be replaced. The pressure line looks just as bad and will develop a leak soon too, if not replaced. While chatting the customer revealed that while stuck with no power steering, he put motor oil into the reserve tank because that's all he had. It did get him home. My plan is to replace the pressure line first, then cut the return line below the car (where it can be accessed better). Then use my evacuator.
hooked to the return line from the rack. Start the siphoning and fill the reserve tank with the proper fluid to flush everything out. I figured that it would flush the reserve tank, pump, pressure line, and rack. Then replace the return line and top off the tank. Will I have to have the engine running while I flush, and do I need to work the steering wheel left and right too.
I am rebuilding the oil cooler and noticed since its removed I have great access to this fuel line pair from fuel bowl to soft lines below. How these disconnect at the soft lines? I happen to have a new set waiting to be installed. Is there a tool required ?
View 3 RepliesOk. I have a 2015 6.7 power stroke and my fuel return line clip keeps falling off. And goes into limp mode. It has happen twice and in come up with code p0088. And I push it back on start the truck and it is fine. But idk why it is doing it
View 1 RepliesHave a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 RepliesEither one of my power steering hoses or the gear box is leaking on my 93 Ranger. It appeared the return hose was leaking where the rubber meets the crimp. So I decided I would go ahead and change the return and pressure hose to see if it stops the leak. It was a disaster. It's 2.3L manual transmission 4x2. I got the return hose off ok. I put the wrong size wrench on the pressure hose fitting at the pump but thought it was loosening but it was rounding the nut off. So I couldn't even change that hose. I installed the new return hose and retightened the pressure hose at the gear box.
Well it was a pain getting the flare fittings of the hoses into the steering box so I could tightened the flare nut down. I finally got them tightened, I think, but then when I started the engine fluid shot out of there like a water hose. It's coming from the fittings at the gear box that I thought were tightened. I reloosened and retightened them again and still it's shooting out everywhere. There is so little room getting a wrench on the hose fittings, it was slow going. What do you need to remove in order to get a good straight shot and installing these flare nut fittings and tightening them down right? If I remove the pump will it be easier to install the hoses on the gear box? I have to remove the pump now to change the pressure hose.
I have a 1990 Ranger with a 4.0L that I just changer the intake gasket on. I broke the fuel line at the Fuel Pressure Regulator. Cant seem to find one anywhere. It is a nylon inside/rubber outside with a cloth mesh and quick connect fitting line. Where to get one? Can I hose clamp it the FPR by cutting off the connector that broke?
View 1 RepliesCouple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 RepliesThe fuel line on the passenger side under the turbo that leads to the head is leaking looks like from rubbing on the pedestal, anyone ever just cut it and throw in some fuel line and hose clamps?
View 14 RepliesI got a 1990 ford ranger 4.0l and is been leaking fuel from where the regulator conects to the fuel line the regulator is new. I cant find a new fuel line.
View 4 RepliesI let my sister borrow my 1995 4 banger Ford Ranger for about a week. To make a long story short, when I drove it home I could smell a really strong gas odor so I pulled into a gas station and noticed gas pouring out of from what looked like the fuel filter area right under the driver's side.
Anyway, it took another 5 gallons to get home and I later crawled under and took a look. It looks like someone grabbed the fuel line and tried to unsuccessfully pull it out of the fuel filter by hand. I could literally see the imprint of the person's hand where they grabbed the line. They had pulled the line so hard that it crimped and split which is why gas was leaking like a water hose.
I picked up a Ranger specific Dorman fuel-line repair kit from Advance and had my brother install it for me as I'm no mechanic. It was fine for a few days and then I started to smell gas again so I crawled under and took a look. There's just barely a small leak coming from the connector barb/union on the kit. Anyway, I didn't know what else to do so I dropped the Ranger off at a local shop this evening. With that said, this is fixable, right?
I have a 2000 f250 V10 CC 4x4 long bed. The rubber fuel line that has a quick disconnect to attach to the fuel filter along frame is leaking. This is on the filter side going to engine. Ford tells me fuel line not available. Dorman products tech assist can't tell me which connector of there's will fit my truck.
View 2 Replies2003 XL 5.3L with a leaking fuel line between the tank and filter. Mechanic says that this line is only available in a kit that includes all fuel lines for the truck. Hard to believe you can't just get the one line.
View 4 RepliesI am a proud owner of '97 Grand Prix GTP, it has always been a great car with really low maintenance for me. A few days ago I noticed a mild fuel smell and I checked the gas cap, the external fuel filter, etc... Then I lifted the hood and I saw that one of the two fuel lines that run between the firewall and the brake fluid reservoir had a seepage leak in front of the factory loom that secures both lines before going over the supercharger and on to the fuel rail. A fuel leak needs to be repaired immediately, so this is where I am so far.
I noticed that the leaking fuel line is actual a rubber/plastic fuel hose that is covered by a plastic heat proof cover that protects the hose. It runs from the firewall to the fuel rail along side another fuel line of the same size (a supply & return line I believe). Just before going over the supercharger they both have quick connect metal ends that meet two metal fuel lines that end up at the fuel rail. My current issue is that this plastic/rubber hose section of fuel line is discontinued and no longer available to order according to my local GM parts dealer. The way I see it, hunting down this part can be Plan A and Plan B can be duplicating this hose by making it with high pressure fuel injection hoses and the appropriate quick connect fittings.
Found out my 2007 Hyundai Sonata V6 GLS needs a new brake line put in. The line rusted and all brake fluid leaked out. I am very surprised that after 7 years and only 103,000 km (about 65,000 miles) the car will need a new brake line put in already. All my other cars have been Japanese and have never experienced premature failure and replacement of brake lines.
Granted, I live in Toronto, Ontario, and this year has been a cold start to winter with lots of aggressive salting. It started to get a little bit warmer the last 2 days which probably accelerated the corrosion from the salt.
I have a 2003 Santa Fe that had a corroded leaking power steering return line. I want to replace both the high pressure and the low pressure lines coming from the steering box. The high pressure removed quite easily. I cannot get the low pressure out. Everything is broken free. Is there a trick to this? I want to see how it comes out so I can put the new one in same way.
View 3 RepliesLooking for the instructions on how to remove the lower power steering belt and replace it. We recently discovered the leak and I can't find any information on it.
View 1 RepliesI have a 04 camry and this car leaks gas after i pump about line before the full line. What do i need to do?!
View 2 Replies