Ford - Ranger :: 2004 - Truck Does Not Pull To One Side Or The Other While Driving
Oct 19, 2013
i have a 2WD 2004 Ford Ranger regular cab. I have replaced the rotors three times in the last year due to warpage. What is causing this? The truck does not pull to one side or the other while driving. applying the brakes don't cause it to pull to one side either. According to my mechanics, neither caliper is sticking. the right brake pad does show some signs of heat damage (cracking). There is no uneven tire wear. I have a buddy who thinks it may be a bent wheel hub, but my mechanic says no because no uneven tire wear. They are leaning to a faulty brake hose, but can't say for sure.
View 3 Replies
Advertisement
I have a 1988 FORD Ranger with the 2.9 liter engine with the four speed automatic overdrive transmission. Several days ago the transmission went out. The truck will not pull in reverse, overdrive, drive, second or first. Usually most vehicles will usually have at least the reverse, A first or second when the drive and overdrive stops working altogether. What the problem could be?
View 1 Replies
The problem : I bought a 2004 Ranger truck and after two days it started to hiccup, or stall or die while driving, then because the truck is manual, just start up and keep running. It was the strangest thing.
I gave it to a shop, and after checking the electrical, the ignition, the fuel system, the drive train, and ten hours of troubleshooting, they came up without an answer. So they gave me the truck back.
Answer, a few days after taking it back:
I had told the shop that it had been sitting for 6 months, May till January, but when I told a mechanic friend a bit later, he still suggested 2 bottles of gas line antifreeze in the tank, before the next tank fill. I did that, and there was some improvement.
Next, When I replaced the balding tires with new Nokian Winter tires, the tire shop, (Kal Tire), told me that the air cleaner was incredibly dirty, and asked me if I would like them to replace it. I said yes, thinking that it might just do the trick, as no one in the forums I read, had mentioned it.
Success! No hiccup or stalling and it has not died since.
View 6 Replies
I have a 2004 super duty diesel 6 with electrical trouble dash lights stopped working put in new fusses where needed still no dash lights but now truck starts and runs ok but will not shut off unless I pull ignition.
View 2 Replies
When I brake hard. My truck wants to veer right. It drives straight otherwise.
I recently had my front shock replaced and prior tp that my truck did the same thing, although it was much worse since my left front shock was leaking. Originally I thought it was pulling because of the bad shock but now that thet've been replaced I am not to sure.
Alignment issue or something else entirely? Coud bad rear shocks cause the issue?
View 14 Replies
So after getting home last night and having a lot of trouble backing into the driveway, having a serious loss of power, I take it out today and find that the truck is rocking from side to side as I drive, a bit like a boat in rough water. Further, I wasn't able to get much power out of it, capping about 20mph/30kph. Reversing produced some ugly grinding or scraping noises. The steering wheel swung very quickly back to its neutral position after turning, and I've noticed a strip on the road near the driveway where I apparently spun one of the tires trying to back in. Some quick searching says it could be a wheel bearing, an axle problem or suspension-related.
View 1 Replies
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 Replies
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 Replies
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 Replies
I'm getting tired of this. Bought my Ex in April 2013
Realized in June '13 that truck would pull to the left a little when I braked. Replaced pads and rotors. Factory pads and rotors looked normal but whatever.
December 2013 - shimmying when braking downhill (not towing). Replaced rotors, pads and calipers with Power Stop.
September 2013 - Everything was good but I now have the the left pull about 35% of the time when I brake. After extended downhill mountain driving (7%+ grade for 15 miles) I get the shimmying. I only get the shimmying in this situation.
When I had my tires rotated (reputable shop) I was told I only had a 2-3k miles left on my pads.
I do drive aggressively so I'm not surprised I need to replace my pads more often, especially on a large vehicle. That said pads wearing out at ~10k miles normal?
I was going to just order new pads and install them this weekend but what is going on. Ex currently has about 64k miles on it.
View 14 Replies
My 2000 ranger, 5 speed, won't start. I was driving, and all of a sudden, the engine just stopped.
Electrical works, engine turns over once or thrice, but it never actually turns on. Wires and belts all appear fine.
View 8 Replies
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
View 6 Replies
Have 2001 F-250 7.3 PSD, automatic, ESOF (had to replace the original hubs with Warns)have kept up the maintenance,oil, grease, ATF fluid & filter, truck has been virtually trouble free. About 2 weeks ago I decided to go across an area of the lawn, as I was going (in 2 wheel drive)I felt the tires spin a little so I stopped got out and locked the hubs, got back in truck turned t-case to 4 high. had to rock the truck out of a damp area but nothing really.
So I got back to where I came in at (in reverse about 100') stopped put it back in 2 wheel drive, tried to go forward, very difficult, sluggish, got back in driveway had to back the truck in, will not go forward at all now. Checked all fuses, rapped the the t-case motor, no codes. So I thought I'd move the ruck, have a winch that will pull it out by the barn, I could not even move the truck forward by pulling it with a winch. As I said have never had any problems with truck. Transmission fluid is good, clean no burnt smell.
View 14 Replies
I have a 2011 F250 6.7 4x4 CCLB. About 90k on the odometer.
Full flopro exhaust(no cat, no dpf) and a H&S tow tune. Otherwise stock.
8" lift and 37" toyo mt tires.
Anyways, I ran the truck in my first truck pull ever a few weeks ago. I pulled in 4wd high, rear locked, tow/haul mode, traction control off 2nd gear.
I wasn't able to pay super close attention to all of the stock gauges, but it didn't over heat and it didn't rev over 3000rpm. It was pulling like a freight train until the 125' mark and it just shut off. I thought something may have broken.... I put it in neutral, cycled the key and it started right back up....
Checked for anything obviously wrong, no fluids, all boots looked attached and fine. Nothing. Drive it home and haven't had a problem since. No CEL, no warning no anything. So why the truck may have stalled on me?
View 14 Replies
I have a 2006 that shuts off in a hard pull, if I wait 3 minutes it starts again. I hooked up my scan tool and when it dies and I crank it it only builds 200psi oil pressure, let it sit it builds enough pressure to run fine. If I dont push it over 3500psi for more than minute it wont die pull a hill it dies again. Is it the hpop or an o-ring.
View 10 Replies
1990 Ranger 2.3 liter. Need to replace washer pump, do I need to pull the reservoir to do this?
View 1 Replies
So earlier this week i took my truck in for a check engine light and a issue when i would pull up to a Red Light my truck started knocking like a Diesel motor. I quickly put the truck into neutral and the issue went away.
Is there an issue with the 5.4L motors mine only had 69000km and was properly maintained with an oil change every 8000km? 2009 F150 5.4L new motor after 69000Km
View 10 Replies
Fuel mileage is terrible also but the truck really has no power. Running down the highway it kicks down just to pull a small incline. Check engine light is not on and there is no hessitation. The truck has 105k on it and i have put only 5k of those miles on. I did pull a couple plugs and they are autolites so plugs must have been changed at some point. Does this sound like a coil problem?
View 5 Replies
Its a 2000 flex fuel 3.0... Its not the actual injector. I think its wiring or computer. No change in idle when I pull the injector plug. But I think I can feel the injector opening and closing. Compared to nearby injector diagnostic light flashes less brightly. but that's pretty hard to quantify
When I pull the plug on another injector it idles about the same but I can tell it surge up and down as I disconnect and reconnect it. Fuel injectors were backflushed and swapped same problem cylinder. Where do I go from here just take apart the loom and look for abraded wires? Its the number one cylinder, passenger front.
View 2 Replies
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
View 10 Replies
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
