Ford - Ranger :: 2003 - Engine Is Revving Above 3000 RPMs
Mar 18, 2013
I own a Ford Ranger 2003, 5spd 6 cyl. My problem is when I'm driving and the engine is revving above 3000 rom's. It begins to sputter and buck as if the engine is running out of gas. It only lasts a few seconds. It ends as quickly as it starts. It does not occur each time when driving above 3000 rpms. My mechanic took the truck for a test ride and of course he could not find anything wrong. His advise was to wait until it got worse. I would rather solve the problem now. It is difficult and dangerous when trying to pass vehicles on the road.
View 2 Replies
Advertisement
2002 Elantra engine is revving up to 3000 rpms when in neutral or park. I changed the Throttle Position sensor and it went right back to revving up. Code read P0121. What might be causing this? Seems like I get one thing fixed and then another code shows up..
View 2 Replies
My car is a 2001 honda accord v6. It sat for 3 winter months. When I go to turn it on in the morning, the car will rev while idling. Jumping between 1000 and 3000 rpms. Why this might be happening?
View 3 Replies
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
View 14 Replies
Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
View 3 Replies
At the beginning December I put my brand new winter tires (general altimax arctics) on the factory steelies and put them on the car gearing up for the snow. Not to long after the install I notice that I was getting a very strong engine vibration starting at 3,000 rpms and it stopped around 3,100 rpms no matter what gear I was in. At first I though it maybe just the cold affecting the engine. Well...
Last week I put my summer rims and tires back on for the 1,600 mile trip to MO and back, and like magic, no more heavy vibrations. Smooth acceleration throughout the normal driving rpm range. I just changed the oil and tranny fluids Tuesday after we got back and with the warmer weather the car is running smooth as silk. Still an awesome car with awesome mileage and couldn't be happier.
View 7 Replies
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
View 6 Replies
When I start my 2003 Escape 3.0, the rpm's shoot up to about 3000rpms. After a few seconds they drop to about 2000 and slowly creep back up to 3000. When I put in gear, I don't even have to step on the gas and my vehicle goes. It maintains between 1500-2000rpms as I'm driving. When I come to a red light or stop sign, it lurches like it wants to go even though I have my foot on the brakes. I've replaced the IAC valve, TPS, had it checked for vacuum leaks, PCV valve replaced. I'm at a loss as to what it could be.
View 3 Replies
2006 Explorer with a perplexing issue that I am scratching my head over. When engine revs to around 3000 RPM, there is a click that sounds like it is under the dash, and the ABS, traction control, and airbag lights come on; if the headlights are on, the dash lights around the a/c controls go out, and sometimes (but not every time) the speedometer and odometer drop to zero. Also, the overhead lighting, if on, goes out. The engine does not appear to be affected. After about 1 second, another click, and everything returns to normal. This happens either while driving or if in park and revving engine. Is this possibly a relay tripping? And if so, why is it triggered by 3000 RPMs?
View 2 Replies
Symptoms- won't rev over 3000-3500 rpm's, upon acceleration (especially uphill) seems to struggle and won't accelerate much at all, seems as if trans changes fine. BTW, throwing no codes at present.
What I have already tried...new air filter, new fuel filter, had cat. check (was told stopped up but when removed found it was not and truck did the same even with cat. off), o2 sensor (upstream) replaced, battery disconnected to reset computer.
After reset of computer, runs a little better but still not good. Seems to start if you accelerate to quickly or when truck reaches around 40-45 mph.
View 11 Replies
So that's what if feels like, in park at idle it sounds great, starts great no codes. IF you floor it it will not go over 3000 rpms in park, it feels like it has hit a rev limiter. I have 60psi fuel pressure at idle and at 3000 rpm.
When driving down the road I won't go over 55 mph and drives normal if you keep it under 3000 rpm, if you give it more gas it falls on its face?
AC is not working (clutch not engaging)I don't know if that's related or not.
We did just swap the motor the truck is a 2003 2wd drive. motor came out of an 2002 4wd. we are running the 2wd harness, computer egr delete etc.
View 6 Replies
I have a 91 ranger with the 3.0 engine. Recently the engine was not reving up when i stepped on the gas. But, it kept running and i got home. Then one day it just wouldn't start after i just shut it off. I've changed the distributor cap and rotor,fuel pump and filter.I have spark to all 6 plugs and good fuel pressure to the fuel rail. I'm leaning toward the timing. Last night I found the harmonic balancer will just spin freely. Will this stop it from firing?If it is the timing, how do I find tdc and where is the # 1 firing position on the distributor cap(no markings)?
View 14 Replies
2002 F-350SD V10 Automatic. Running down the road with no load or with load. First gauges bottom out, next overspeed light starts flashing, engine goes to 3000 RPM on it's own. Stays that way until I shut off then restart. Sometimes it does this several times in one mile.
Second trick, again driving along, all gauges stay up but engine just stops. Got to set dead for 5 minutes before it will start. The shop says on the first problem this happens: Voltage goes way low then goes way high then everything starts failing. We changed battery but no luck. Got to be down line from battery.
View 6 Replies
I've been getting a blinking engine check light.. I pulled all the codes:
P0050: H02S Bank 2 Sen 1 Heater Circuit
P0155: O2 Sensor Heater Circuit Malfunction Bank 2 Sen 1
P0304: cylinder 4 Misfire detected
P0688: ECM/PCM Power relay sensor circuit
I've had the car sitting for awhile because I lost my job and didn't have any money to roll it around much.
I just changed out the spark plugs and two of these had a white coating on them.. I was hoping this would take care of the misfire after I replaced them. I also bought a new battery because mine had lost charge a few times.
The Car will run with an engine check light, but if I go past 2500-3000 rpms then it will start blinking (which means don't drive it )
The oil has been sitting in it for about 2 months, so I'm about to go change that and I'm hoping this will allow me to drive it without issues.
Any of these codes thrown and know what they could be? Which O2 sensor (like a link to a website that sells them). Trying to get this thing running again.
View 7 Replies
I recently purchased a 2013 elantra.
I have noticed that there is engine vibration and noise felt in car and pedal when accelerating at around 2500-3000 rpm's before it shifts. Is this normal behavior? It just does not seem as smooth as it should be. I have only put about 600 miles on the car.
It has been very cold, but it does not go away after warming up.
View 10 Replies
On my way to the grocery store my car's RPMs started to pulse up and down (between 1 and 2) when driving. While stopped at the red light it would vibrate very hard. When i put it in park the RPMs would rise fast before i shut it off. It did the same things on the way back home plus the check engine light came on. A few hours later i put a little oil in it and drove it around my neighborhood and it didn't do any of the things it did that morning.
View 5 Replies
2003 Honda Odyssey EXL with 236,000 miles on it was jerking, very scary, and the rpms were revving up while driving. We asked around and had it checked and was told it was the transmission. We waited 9 months, not wanting to put the money into it and let it sit, not driving it at all. Then we decided to fix it last week.
We thought we were replacing the transmission, but, after working on it, the place we took it - very reputable - only did the solenoid, saying that fixed the problem. When we took it home an hour away, it was fine - much, much better than when we left it. But, the next day my husband felt a small jerk. We took it back that night and left it with them for a couple more days. They couldn't make the problem recur, so they sent it home with us. We were getting ready to go on a major road trip, so we had the oil changed, and all other stuff for regular maintenance seemed good. Had all fluids checked and new tires on and new battery. Also had recall done on ignition switch. Left on major cross-country trip. Drove about 5 hours and it started again. Just a little - one time. No place was open and we were on deadline, so kept driving cross country.
Eventually the check engine light came on (can't remember if it was before or after started jerking), but that has been on for a couple years and we keep having it checked and they tell us it is not worth fixing - hard to figure out the emissions problem. Could be several things. One was the solenoid, another the gas cap. We had both those replaced. Problem has gotten worse as we have crossed the U.S. on Memorial Day weekend - so no opportunity to have mechanic look at it or get codes due to everything closed. Checked transmission and oil fluid levels, and they are good.
If we accelerate VERY slowly, we are okay. But, the TCS light comes on if we accelerate too quickly sometimes, and it will stay on until we stop and turn the car off. Sometimes it doesn't come on at all, but the check engine light is always on now. In the last 200 miles, we now have occasionally the D (drive) light flash - if the TCS light is on and we are getting jerking, and the rpm's stay up in the high 2's or close to 3 and the van doesn't seem to shift into the higher gear. If it flashes, it won't quit or shift into the higher gear until we stop for maybe 20-30 minutes. Then, the light will stop flashing and the rpms are okay. As long as we accelerate really slowly, really slowly, it won't flash again. One time, on an off-ramp, we jerked when we were decelerating, but that was only once in about 1500 miles - or ever as far as I can remember. The jerk on acceleration has actually been going on for a couple years, but it was always just momentary and only occasionally. Now it is a problem.
View 4 Replies
Not sure who wants to ruin my night, but here's what popped up for codes:
Also, the engine sounds like a sewing machine when revving up to about 1,800 RPMs, then the engine sounds fine. Lastly, the far camshaft makes a knocking at idle after engine warms up.
If this indeed needs a timing replacement, I've done everything on the car myself, but this would be a stretch.
View 24 Replies
Might be a long shot here, but I JUST had this noise/rattle pop up in my '12 GTI 6MT w/ 13k miles.
Turns out I found someone who posted a video with basically the same noise:
Another one:
I hear the same noise while stopped and revving the engine as well as when driving if I let off the throttle and let the RPM's sweep down past the same rev range (1,800-2,000). Sounds like it's coming from the passenger side area.
I'm under warranty so I'm going to take it to the dealership...but I know how they can be with rattles.
View 8 Replies
I have a 2002 Ford F-150 with a 5.4 Triton. 212,xxx miles. I replaced the cops and the plugs about 6 months ago. I was pulling a trailer up hill last week and the engine was under a load doing about 3000rpm. It began to misfire and give me a flashing mil. However, before I went very far the engine began to run fine. It happened 3-4 different times. However, there is no code recorded. I've driven the truck nearly 100 miles with no problems, but I'm going to be pulling that trailer uphill again next week.
View 8 Replies
Let's say I'm going from zero to forty, my RPMs will hit over 3000, but when it shifts, the RPMS will drop down to 2000-ish really hard, making the car jerk. It's not a smooth drop, it's like a split second. Upon acceleration there is also a very rapid knocking sound. There's no lights on my instrument cluster.
This trouble all started after I had my alternator die, then having the car towed a few months back. Ever since then this problem has been getting worse. Wat this could be?
View 1 Replies
