Ford - Ranger :: 2002 - No Clutch Pedal Or Shifting Hard
Aug 17, 2013
When I bought my ranger used, the clutch felt ok. But as a couple weeks had passed, it started to get hard to shift. The clutch doesn't slip at all so a friend of mine said there might be air in the system.
I would pump the clutch pedal a few times and then it would shift ok for a while, then back to shifting hard. I found the bleeder and had my son assist me with bleeding the system. Everything was fine at first but I made a big mistake and now i have no pedal feel at all.
My mistake was i didn't realize what I thought was the reservoir was not the actual reservoir. There was a black rubber thing in the reservoir that I filled with fluid. My mistake was I needed to take out this black rubber thing.
So now i am stuck with no pedal and don't know what to do. When I pulled out the black rubber thing, the reservoir was empty so i filled it and it bubbled for a second and then stopped. Tried pedal at this point and there is no feel at all. It just goes to floor with no effort.
View 8 Replies
Advertisement
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies
95 ford ranger clutch pedal very hard when hot. Will not engage clutch. Ok after setting for 1 hour.
View 1 Replies
This is unusual. After driving into town for new tires, the clutch pedal was hard and I could not depress it after the tire tech parked the truck. It did finally depress with a pop, though the pedal functioned there after the clutch did not function properly.
At times it seemed to be ok at other times it seemed weak. I stopped by Autozone and checked the fluid, seemed low and I added some. Continued home not completely confident that I would make it. Had to make one stop along the way.
Once again the clutch pedal was stuck at the top and would not depress. I finally slid the safety switch up the clutch shaft to start the truck, when the engine started the pedal depressed. I was able to continue home but the clutch is not functioning properly.
View 2 Replies
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
View 3 Replies
1992 Ford Ranger 4x2 with 2.3L engine and 5 speed manual transmission. 135,000 miles, no AC and no power steering. I am having poor clutch disengagement and resulting hard shifting. The shop added a little fluid to the reservoir last oil change and it is still looking full. I always park on concrete and never see any leaking. I don't know what may have been done before as I haven't had the pickup all that long. Where should I start? Is there probably internal bypass leaking in the hydraulic clutch as there seems to be no external leaking?
View 4 Replies
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
View 14 Replies
I've had my truck a few years now but for 2 it was basically parked. When I started trying to use it again I am having issues with the clutch now. When it is cold everything is fine, but on hot days or after I have been driving for a while It will lock the pedal up and will not let me dis-engage the clutch at all. Sometimes when it does eventually let the pedal down it will go to the floor and stay there for a few seconds until it slaps back up and engages slamming the truck into gear.
I have yet to try much. I'm not good at working on anything other than stereos in cars but I am willing to try. My thought is some water got into the system and is boiling in the lines but I am not sure. Places to start? I really need my truck going and the couple places I've taken it dont even want to try it seems like.
View 2 Replies
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 Replies
I'll drive my 2000 Ford Ranger, 4cyl XLT about 5 miles to the store without a problem. On the way home, after a few miles, the clutch pedal will either jam at the top, or go all the way to the floor without engaging the clutch. If I wait 5 or 10 minutes, the clutch pedal will start working again for a short time.
If I feel the clutch pedal starting to misbehave, if I ride the clutch and don't release the clutch pedal all the way, and if I don't push the clutch pedal all the way down, I can keep driving the truck. As soon as I release the clutch pedal, it will jam up again, or the clutch pedal will go all the way to the floor without engaging the clutch. I don't like riding the clutch, but that seems to be the only way to get home once the clutch pedal starts jamming.
It certainly seems related to the engine warming, or heating up. Sometimes, after the clutch jams up, I'll wait 5-10 minutes and the clutch pedal will start working as if nothing every happened. So, it can't be strictly a hot engine, hot clutch fluid issue, right?
What would you attempt to replace first, the Slave Cylinder? The Master? Changing the fluid? Shooting the truck!?
View 8 Replies
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
View 6 Replies
Had my original clutch replaced by mechanic. Had 200K on it. Car clutch petal vibrates badly when bringing clutch pedal out after shifting. Mechanic states it has to do with motor mounts that were affected when changing clutch or the clutch takes time to seal and stop vibrating in the next 500 miles. I have warranty for 12 months and 12,000 miles. Which I had no problem of vibration before having clutch replaced? What is the problem and how to proceed.
View 3 Replies
I have a 01 7.3 F-350, 120000. I rarely get down hard on the go pedal but a while back I did and heard at pressure whistle just before it would shift. I thought a bad turbo hose so I replaced them all. 'While working on the hose mounts I cleaned up the castings for a better seal'. The hose replacement seemed to get the running but the whistle is still there. I am thinking a leak on the manifolds for the Y-Pipe connection OR does the turbo have a release valve that can make a whistle sound?
View 8 Replies
my 98 ranger od/ light is blinking and shifts hard took it to a tranny shop they rebuilt the tranny & replaced torque converter got truck back drove for a week got on highway o/d light blinking again took back to tranny shop he said truck needed good tune up to get a diagnostic reading tired of the excuses they give me. Ready to take to another shop then sue 1st shop for bad work the ranger has a 4.0 v6 at 4wd ?
View 3 Replies
I have a 2000 Ford Ranger 4X4 XLT with a 5R55E automatic transmission.
Coming out of a stop the truck jolts at about 20 mph as it shifts from 2nd to 3rd gear. It feels like it revs too high in 2nd gear, up to about 2400 rpm, and then shifts hard into third. It feels like the truck gets a gentle hit from behind.
Earlier in the week, the O/D light flashed. I took it immediately to an independent tranny shop who pulled the code for me: P7033, incorrect ratio in 3rd gear.
They cleared the code for me. In limited city and highway driving (less than 15 miles each trip) the O/D light has not flashed again. But the problem remains. I plan to take it back to the shop later next week.
What might cause this so that I might have a more informed conversation with the tranny mechanic?
View 3 Replies
Just picked up a 2003 Ranger XL 2.3L and notice that I get a little grinding every now and then when shifting into 1st gear. The clutch was replaced 3 years ago according to the PO but had no clue as to how long it's been since the clutch was bled.
I've used my Motive pressure bleeder numerous times in the past on brakes with much success but I've never used it on the clutch. I've used vacuum bleeders as well but it's always a 50/50 success rate with that. The pressure bleeder just works much better for me.
Using a pressure bleeder on a clutch and if so any tips like still needing to tip the master cylinder end up to release any potentially trapped air bubbles?
View 5 Replies
I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
View 5 Replies
I have a 88 ranger supercab 2.9l 4x4 with the fm146 trans and recently I have had a problem with my clutch master cylinder rod falling off my clutch pedal. I bought the new bushing and put it on and it was fine until yesterday. It wants to keep coming off. Is there a clip of some sort to hold it on or no. I looked at a few at the salvage yard and they did not have a clip just the bushing. So what do I do?
View 1 Replies
I think the time is near for a new clutch in my 98 Ranger, 2wd/ 5 spd. How tough of a job is this? I've changed the one in my 66 Mustang years ago but things were less complicated then.
View 3 Replies
I have about 350 miles on my new jetta and i will like to know if its just me or did everyone with a manual go through the same, i feel that up shifting at higher rpms like 4k i feel like the clutch is grinding i actually feel it in the pedal, I haven't gone higher than 4k due to break in period. I also notice that there is no engage while getting out of first almost like its slipping but it is not, i have driven manual most of my life so i know i am not slipping the clutch.
View 4 Replies
I'm looking for a part number for the rubber stop that mounts behind the clutch pedal on the firewall for a 2001 Ford Ranger 4cyl 2.3L 5spd Manual. Can't seem to find it on the web. It looks like it snaps/presses into a mounting hole behind the pedal. The original one decided to disintegrate and now I get a nice knocking noise when ever the pedal is depressed.
View 7 Replies
