Ford - Ranger :: 2001 Cranks But Not Start
Dec 8, 2015
My 2001 Ranger is used for work to move furniture multiple times in a day. 7 weeks ago, I had moved a dryer w/ it, drove across town for a meeting, got back in & it refused to start & run. The same thing happened 3 days ago on a longer, fuller route w/ a trailer attached. Both times, the truck started & drove home ok AFTER sitting off waiting for my emergency ride. While I waited, I looked up the issue in the owners manual which told me to depress the gas pedal 1/3 to 1/2 & then turn the key in ignition. The first attempt did not work, so I repeated the steps, which started the truck & I was able to drive back. Both times, the truck started no problem the next workday. Does this sound like a problem worth fixing (for the age of the truck vs. cost of repair)? It has pull some weight, including on trailer, in between the two occasions.
View 1 Replies
Advertisement
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 Replies
Ok, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
View 14 Replies
My 1999 Ranger that I bought used has been serving me well. However, two days ago I went to visit a friend and when I tried to start the truck to go home, the engine cranked but would not fire. I assumed that perhaps I had flooded the engine, so I walked home. I went back an hour later and the truck started up immediately. Then, yesterday, the truck would not fire at all. I towed it to AutoZone to check for error codes, but none were found. I put my inductive timing light on a plug wire and found that there was no spark.
In one instance of cranking, the timing light blinked and the engine tried to fire, but then nothing. The AutoZone man suggested changing the crankshaft and camshaft sensors. I haven't done that yet, but that is my next plan. Can the Ford dealer find error codes that tell what is preventing an engine from starting that AutoZone can't see? For sure there is no spark, but maybe there is no fuel either since I don't smell gas after much cranking. Could it be the inertia switch cutting off both fuel and spark?
View 14 Replies
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
View 4 Replies
2004 3.0L Ranger Edge, 88,000 miles on it, I am the original owner. It won't start. It cranks strongly. Usually when this happens, I have to reset the fuel pump inertia switch. This time, resetting the switch does not work. I disconnected the switch and jumped the two wires going to it, but still no start. The switch seems to work ok, in that I can reset it (a ball, spring, and magnet mechanism, I think), then shake it and the ball will come loose.
The fuel pump 20A fuse in the engine compartment is good. The fuel pump relay in the engine compartment is good (I switched it out with an identical relay that runs the fog lights without problem). I am getting spark. I don't have a fuel pressure gauge but pressing in the Schraeder valve on the fuel rail produces gas.
Usually, when the inertia switch is tripped I can get the engine to briefly start by using starter fluid in the air intake. But not this time. I do not hear the fuel pump kicking in when I turn the ignition key to the "On" position, and that would lead me to think that the pump is bad. Except, I don't get a brief start using starter fluid. The fuel filter has never been changed, but again, since I get no start with starter fluid, I don't see how that could be the problem. OBDII scan shows no codes.
View 7 Replies
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 Replies
I have a 1995 Ford Ranger, manual shift. It always starts when cold, but sometimes -- very sporadic -- it will not start after I've gone somewhere. This has happened maybe 8 times over the past 18 months or so. Always, after sitting a while, it starts right up as though nothing happened. Several months ago I left it with a mechanic for an entire week, but he could never get it to act up. Of course.
In browsing through these discussions, I've seen the "starter/clutch interlock switch" mentioned. Here is my question, though. Would the starter still crank if that was the problem? or does that switch stop the starter from engaging?
When mine acts up, the starter cranks, the engine turns over ... it just acts like it's not getting fuel. Is that a starter/clutch interlock switch issue? Or something else?
View 3 Replies
I have a 2003 Ford Ranger 4X4 4L AUTO. About once every 6 months it will not start. It cranks just fine but doesn't fire. After about 45 min. it start and runs great for an other 6 Months. I have replace the plugs, wires, distributor cap but it hasn't solved the problem. It has had this problem when it is cold and warmed up.
View 4 Replies
99 Ford Ranger disguised as Mazda B2500. (Same vehicle I think) 5 speed manual, 4 cyl., no a/c. Bought new and maintained according to schedule. Randomly fails to start. Cranks but won't turn over. I try several hours later and am able to start it. Mechanic has not been able to duplicate the failure to start. Checked thoroughly and finds no problem. I am very hesitant to drive it like this.
View 6 Replies
2007 Ranger 4.0.... Initial start of the day it cranks a bit longer than it should. After warm, it starts fine.
View 1 Replies
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
View 14 Replies
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
View 14 Replies
i just rebuilt the motor in my 2002 ford ranger 3.0 and it wont start it cranks over but back fires and bucks alot. took the plugs out and it gets spark and fuel. when it sparks it sparks like multiple times.
View 3 Replies
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
View 4 Replies
it's been parked for about 2 months in my driveway, which slants upwards. I cranked it for a solid 30 minutes (jumped the battery so it wouldn't die). I don't smell gas so I think gas isn't making to the motor.
View 1 Replies
I have a 2001 mustang convertible in good cond. A 6cly that I have had very little trouble with over the past year. I put in a new battery then, just after I bought it from a dealer. The dealer had gone over it with fluids etc. and I had a friend look it over when I bought it. He said it was very clean and a good buy. So, last week I started having trouble starting it in the morning. It would crank but would not fire. I turned the key off, and then tried again, Same result, cranks but doesn't start. I turned it off again and being worried about draining the battery, I turned everything off, radio, heat and fan, lights. Then I tried to start it again and, it started. I'm thinking I need new plugs, but I ignored the problem and went to work.
A couple days later I was leaving the grocery store, turned the key and same thing again, cranks but doesn't fire. I knew what to do. Turned off everything and tried it again, it started. Ok, so now some repair, possible plugs, is on my priority list. I need to get this fixed before the bad winter weather comes. Yesterday, after a long day at work, I was ready to go home and I it happened again. This time it's terminal. No matter what I did I couldn't get it to fire. This morning it's sitting in the office parking lot and I need to deal with this today.
Could be plugs, could be the fuel pump. Before I call the dealer and pay 4x what I should for this, what do you think it could be? 3.8 6cly. The car is sitting on a slight incline, in the parking lot. Gravity pulls fuel from the engine to the gas tank, if a fuel pump is going bad this could be why I can't get it to start. I'm going to roll it to a level area and hit it with starting fluid to determine if the pump is bad. I'll also pull a couple plugs.
View 18 Replies
I have a 2001 F150 Supercrew Lariat. About a month ago I stopped to fill up with gas and afterwards it would crank but not start. After a few tries the engine would no longer turn over. My battery was 7 years old so I replaced it and the problem went away for about 5 days. Then the same thing, crank but no start. I checked all the fuses & called the local Ford dealer.
After talking with the parts dept. I tried hitting the panic button then the truck started. After talking to parts again I replaced the PATS transceiver. After 3 weeks with no issues the problem came back. This time I locked the doors with the keyless entry remote then unlocked them & the truck started. So I'm wondering what is my problem. Could it be the PATS module or something with the keyless entry module or some other issue.
View 14 Replies
F-150 Super Crew 5.4 4X4 cranks won't start. what and where do I check first?
View 8 Replies
About a month ago, my 2001 f150 supercrew (4x4 5.4L) didn't want to start one morning. This was after a very cold night (15 degree temps). It sounded like it had plenty of juice in the battery (cranked good), just wouldn't start. Later in the day, after it warmed up, still no start. I dug thru here, and someone recommended disconnecting the positive battery cable for a minute then retrying. I did it, and it worked. All was good.
About a week ago, no start in the morning again. Tried the positive cable disconnect, no luck. After several hours, it just seemed to randomly start, and all was well again.
Today, truck started right up in the morning, but later in the afternoon (warm winter day 45 degrees) no start. Tried the positive cable disconnect, no luck. After screwing with the truck for about an hour, I decided to put the fuel pressure gauge on the rail. NO fuel pressure.
Is fuel pressure associated with the PATS, or is this a straight up fuel system problem?
Additional info: My gas tank fell out this summer, (recall on those tank straps), and I had a new tank, pump, straps and lines installed. I had a no crank, no start issue this summer, but that turned out to be the transmission not registering in park. I assume the two issues are unrelated.
View 7 Replies
After driving my truck for a few hours a day it doesn't want to start it cranks ok but it just wont start it feels like no fuel is getting to the injectors. I let it cool down around 30 min then it just starts this happens to me twice a week approx. i replaced the fuel crank sensor. but to no avail.
View 3 Replies
