Ford - Ranger :: 1999 - Gears Locked / No Forward Or Reverse And It Wouldn't Roll In Neutral
Jun 10, 2012
My low miles (under 50k) 1999 Ranger has a 5-speed manual transmission. One morning, I could not move it. The shift lever shifted, but the gears were locked. No forward, no reverse, and it wouldn't roll in neutral. Eventually, I popped the clutch, and, with a loud BANG! restored itself.
Background: I had rolled the car up tot the curbing in my driveway, so the wheels touched, then shut it off (in gear) and finally set the emergency brake. I'm guessing that this caught the gears in a way that caused the problem.
Yes, it's running just fine now. What happened?
View 5 Replies
Advertisement
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 Replies
My 1999 7.3l Disel 4x4 transmission quit on me the other day. No forward or reverse. Got towed to my regular repair shop, and they are treating the transmission as a black box and recommending total replacement. The diagnostics they performed were to make sure it was shifting, and that indeed it wasn't going forward or reverse. They drained the fluid and said "it's pitch black" and said it had to be completely replaced.
Fluid level was OK, and it wasn't hot. I was driving along, and merging onto the highway. It downshifted, shuddred, and nadda. Free rev. I coasted to the next exit and into a parking lot. Verified that it was shifting, checked Rev and all forwards. It wouldn't shift into 4W, and 1-2 also wouldn't move.
I'm trying to figure out what might have happened... and if it's worth trying to have the truck towed to a transmission shop and have them diagnose and rebuild, vs just getting a remanufactured transmission. None of the local wreckers have any used transmissions, and the cost between a reman and a used is pretty negligible...
Not sure what the symptoms points to for exact failure mode, be it the torque converter, pump, input shaft, etc... I've never had an automatic transmission apart before, but built plenty of motors and am a machinist by trade. My preference is to try and root cause the failure...
View 1 Replies
Driving yesterday, (slowly down bumpy gravel road). My 2005 Prius locked up, the red BRAKE and the yellow (ABS) indicator lights came on. The car wouldn't go forward or back. I tried setting the emergency brake then releasing it - nothing. Still couldn't go forward or backward. I shut it off, turned it back on, nothing, tried setting the emergency brake then releasing it - I finally was able to drive, but the indicator lights were still on and when I tried to brake, there was nothing, nothing, nothing, then BAM the brakes grabbed and locked up. (This happened several times in a few blocks as I was cautiously trying to test the car out.)
I parked got out my owners manual which said "STOP, contact Toyota Dealer" so I had my car towed (first time ever for her to be towed) to my mechanic (he's out hunting, so someone else at the shop looked at it.)
The shop called and said it was showing a code of 1247 and said that it was a "malfunction of the brake pedal". They said they cleared the code and the lights went out. Their mechanic is going to take it for a test drive trying several 'braking scenarios'. (they better not wreck my car).
View 5 Replies
My son called me today to pick him up. His 98 S10 would shift into gear but wouldn't go forward or into reverse. New clutch 6 months ago, hoping something simple like low gear oil or worse?
View 1 Replies
I have a 98 expedition with a 4.2 liter 4x4 and what I believe to be a 4r70w transmission (u code on the door sticker)
The original transmission went at 105k miles and was replaced with a new factory ford transmission by a ford dealer 3.5 years ago. The new transmission only has 10k miles on it.
Now the new transmission only has reverse. reverse works like normal but no forward gears. the idle will change when i put if in gear, but will not move, acts like it is in N . There is no strange noises.
It's hard to believe a new trany is shot already, no towing, or off road use.
My question is : is there ANYTHING that can go bad that would cause this? The trany fluid is clean and clear bright red, and no burnt smell.
I want to check everything I can before calling a tow truck to have it looked at. I will have it repaired if needed, but I don't think I want to replace another tranny.
View 14 Replies
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 Replies
I have a 95 F250 with 7.5 and E4OD. I was towing my Jeep and trailer out for the weekend a few months back (its been parked since) and heard some noise coming from the trailer. So at a stop light I put it in park with the engine running for a second, went to put it back into drive and it hasn't gone back into drive since. Reverse works perfectly. Fortunately I was able to back up onto the center divide, unload my Jeep and back the truck onto the trailer and tow home with my buddies Chevy. Anyways, its been dead since. Where I can start to look? None of the forward gears work at all.
View 13 Replies
The other day I was leaving my house. I started the car and heard a quick, loud chirp. That was the only noise it made so I continued to leave. I rolled out of my driveway and proceeded to put it in drive and found myself rolling backwards. I tried every forward shift, kicked on the 4x4 and continued to roll backwards. I thought reverse worked but found that it wasn't engaging either. My question: is there anything I can look at before resorting to taking it to the tranny shop? I'm in school for automotive and am confident in my abilities to test solenoids and maybe even dropping the valve body to check that. Other than that, I lack the skill to pull the tranny myself and work on it.
View 3 Replies
My '87 Chevy S-10 transmission slips like mad in forward gears and I can't go everywhere in reverse. The truck is gaaged in southern Virginia about 60 miles from my home and is used on some country property. The local transmission shop wants $1600 to rebuild the trans. He says he used sturdier parts than the replacement GM parts. I'd like to fix the truck because it comes in handy and was my dad's old mode of transportation around the Va. countryside, so it has sentimental value.
View 3 Replies
I'm having trouble with the automatic transmission in my 04' Elantra, it acted like the speed sensor was failing, but later the same day it lost all gears, forward and reverse. after turning the car off and sitting a while I started it back up and had gears again, but the trany is making noise. Fluid level is ok.
View 3 Replies
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 Replies
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 Replies
I have a F150, 2nd 4.6, 122,000 miles. No forward gears. When put in drive, you can feel it trying to engage, but doesn't engage completely. Reverse is a solid engagement. Replaced filter and fluid, same issue.
View 12 Replies
I have a 1999 F-250 4X4 7.3 lit Diesel engine. My problem is my transmission will go into reverse great no problem but it won't go forward. I have no problem rebuilding the transmission if that's what it needs, I just want to make sure there isn't a electrical issue from the PCM first?
View 14 Replies
I was driving on the highway last night when it was like somebody dropped my transmission into neutral. I was cruising at 50mph slight hill. There was no noise or any thing. Now I have nothing.
It's a 2005 f350 4x4 automatic
I can only assume I'll be needing a new transmission but I am hopeful of a small problem...
View 1 Replies
Ford AOD in 1988 F150. It's my first time rebuilding a trans and after install will not roll in neutral. I guess this is part of the learning process but I really need to get this fixed.
View 9 Replies
I don't know why... It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problemo, then when put it in Drive it revved like it was in neutral.
There was no banging, no clunkin, nothing to make it seem like something catastrophic happened. I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more.
Next I did the obvious and checked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new. I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
I am on a tight budget and working on my back. I am willing to take the tranny out and bring it into town. Personally I think it's electronic but I don't know ...
Why THis thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings?
Can this be a "worn out" valve? or gasket issue? I really want to avoid removing the tranny at all costs so if there is something I am missing let me know and if you think just yank it out I will.
View 3 Replies
My 2000 SD 7.3 has developed a quirk. For some reason the trans has decided to shift late in all gears. This only happens once, then resumes shifting normally. However the OD indicator on the shifter blinks from that point forward. Once the engine is shut down and restarted. The sequence starts again. Late shift, through the gears, once, then shifts normally with light blinking. Fluids are up and clean.
View 4 Replies
The trany is less than a year old rebuilt by a local shop.
Starting two days ago when i put the shifer in anything but reverse and 2nd it acts like it is in nurtral. 2nd and reverse are strong and do not slip. do you think its in the linkage? Or is my tranny dead?
its a 99 f250 256K auto 4x4 xl
View 2 Replies
Have 2001 F-250 7.3 PSD, automatic, ESOF (had to replace the original hubs with Warns)have kept up the maintenance,oil, grease, ATF fluid & filter, truck has been virtually trouble free. About 2 weeks ago I decided to go across an area of the lawn, as I was going (in 2 wheel drive)I felt the tires spin a little so I stopped got out and locked the hubs, got back in truck turned t-case to 4 high. had to rock the truck out of a damp area but nothing really.
So I got back to where I came in at (in reverse about 100') stopped put it back in 2 wheel drive, tried to go forward, very difficult, sluggish, got back in driveway had to back the truck in, will not go forward at all now. Checked all fuses, rapped the the t-case motor, no codes. So I thought I'd move the ruck, have a winch that will pull it out by the barn, I could not even move the truck forward by pulling it with a winch. As I said have never had any problems with truck. Transmission fluid is good, clean no burnt smell.
View 14 Replies
