Ford - Ranger :: 1995 - Loss Of Power Steering Pump
Apr 12, 2015
I have a '95 Ford Ranger, 208,000 miles, manual transmission. It's always run well but about four weeks ago I began to have a loss of acceleration. This had gotten so bad now that I can't drive it. I can't make it up the smallest hill; and top speed is about 30 mph. I've taken it to the Ford service center here, and they say it's because my power steering pump is going bad and has to be replaced. Sounds odd to me; but what do I know! The repair is about 450.00.
View 5 Replies
Advertisement
I have a 2000 Excursion. This weekend, I noticed some intermittent failure of the power steering where it seemed like the pump was not engaging and then would all of the sudden. Deciding to try to head off a failure, I got a reman unit from Oreilly and installed it this morning. It was fine when I tested, had good brakes and went locked to lock quietly without fuss. Let the house and within a mile, I lost steering and brake assist. I stopped and turned around, but what I am noticing is that at idle, I have no power steering, but when the RPM's are up, I do.
View 3 Replies
My 1995 ford ranger with a 3.0 will not start. It acted like the fuel pump was going out so I replaced it. I also replaced cmp sensor and the camshaft synchronizer due to old cmp sensor broke and messed up the synchronizer. My truck is getting fuel and spark but still will not start. Where do i go next?
View 4 Replies
I have a 95 aerostar with the 4.0. After driving a while it wants to lose power. It only happens after the van has been running for a while, at least 2 hours or more. So of course I have mostly noticed it at higher speeds because I was on the interstate going a long distance when it happened most recently. But it has also happened at lower speeds, after the van had been running/driving for about 4 hours. The van doesn't die right off. It is idling as the van slows down. So I can come to a stop, and the van is still running. I can get out and look at it sometimes, it eventually will cut off. Pushing the gas does nothing, other than perhaps encourage it to stall sooner. It is a complete loss of power but the engine remains running at an idle. If I wait 15 minutes it will go a couple more miles down the road. If I wait about an hour, I can get even further. Let it sit overnight and it seems like it will drive endlessly but not so.
If I try to restart it immediately, sometimes it will run/stutter for a moment. I can wait a few minutes and it will run for a minute then die. After repeated tries to get it to start and stay running it just won't, and then I just wait patiently for an extended amount of time (30 minutes or more). Also on a couple of occasions the exhaust has smelled very rich, and sometimes was black. All of this has been in the last couple of days and 600 miles. It isn't throwing any codes.
View 11 Replies
3.0 ENGINE - For a year now I could not figure out what was wrong with my van. It has a loss of power low end but seems to run OK at higher speeds. I changed the plugs, wires, cap etc, fuel filter and no difference. I finally broke down and took it to Firestoneto diagnose it. The guy told me #5 plug was foul and had oil on in, said it is possibly the rings. They did not charge me but they also did not do a thorough check either. They did not check the compression in the cylinder or other spark plugs.
Spoke to a guy at the auto part store and asked what I could do. He said change the oil and add a can of restore. Also said to put a anti foul adapter in first and then the new plug, the adapter would keep the oil from fouling the new plug.
I got the oil change and added the restor. Drove it for a while and took the plug out myself, its the 2nd one in on the drivers side. The plug was nasty looking. Put the new plug in and started it up. I can see that there is spark going to the new plug but putting the wire on and off made no difference in how the engine ran, like the cylinder was dead. I took the plug out of the adapter and put it back in, still nothing, I took the plug back out and there was no oil or smell of gas. Fuel injector not working? You would think there would be some combustion with the new plug.
A year ago the problem started where the van would run great one day then crappy the next. Sometimes it would run a few days great(like new) then a few days crappy. After a month or so it just ran crappy and basically has ran the same for a year now. I notice the A/C puts a load on the engine and the A/C clutch will click on and off every few second when the van is in gear but not when the van is in park or neutral. A/C is not low and works fine when driving, very cold. I normally turn the A/C off during take off because it takes off much slower with the A/C running.
The van shows some white smoke when I rev it up real good when I first start it but it does not show any smoke when idle and while driving.
View 4 Replies
My truck lost its exhaust a few months ago and it's on the back list of things for this truck so I've been running it without it. However, my neighbors do not like it so, I frequently shut the truck off and coast in down my driveway to park it when it's late. But anytime I do that, I will park the truck and notice a puddle of ATF(ps) on the ground and the PS pump goes empty. Nearly no loss for a weeks when I don't turn the wheel with the motor off.
View 2 Replies
My issue. 95 short Aerostar, Vulcan engine, A4LD trans. Just got it last week. Bought a new trans and when I went to pull the van into the shop, it wouldn't start. Cranks but won't run. First thing I checked is fuel pressure, got zero. Pulled the kick panel and found the inertia switch, but the harness for the switch is getting 1.8 volts with the key in "ON" and the same with it in "START". IIRC it should be zero in RUN after a second or two (if the engine isn't actually running, that is), and 14 in START.
Checked all fuses in the panel by the steering column, they're good, and switched around the 3 relays by the battery. No good and I don't hear the FP relay when I turn the key. For now I'll run wires directly from the battery to the pump, just til I get the trans done, but it needs to be fixed anyway because I plan to make this van a DD. Here are my questions:
-Is there a second fuse panel I didn't find?
-Could this be a computer issue? If it is, would the computer fuse be blown?
View 2 Replies
I have an 04 Ford Explorer XLT 4.0 Flex Fuel. There has been loss of power to fuel pump. Relay and fuse both good, replaced the inertia switch...still nothing. Could a FPDM (fuel pump driver module) have anything to do with this issue? Or what should I check next? I am definitely at a loss as to what the issue could be! I know it is fuel related because I used starting fluid and it started right up and run for just a few seconds, so that should rule out ignition I think.
View 3 Replies
I am the original owner of the car, which has approximately 125k miles on it. The car has given me great service, but lately a strange problem arose that has my mechanic stumped. When I try to accelerate, the car typically does not respond. After 5 seconds or so, the engine suddenly comes to life and the car begins to accelerate. At high speeds it is not an issue, but the engine sputters once in a while. It has never stalled. It is not the transmission because the RPM stays low during low-power times.
The mechanic initially thought that it was a dirty fuel filter. But, changing it has not worked. Once the engine light came on, and the code was for the air-flow sensor. But, the mechanic is not convinced about that.
The problem tends to become worse after driving for a while, after the engine has warmed up.
View 8 Replies
I have a 1995 Camry with the 4cyl 5sfe engine and a manual transmission with about 120K miles. It's been very reliable overall, but lately it's been exhibiting some strange intermittent behavior. When driving at a steady speed between 2-3K rpms, it'll sometimes experience a momentary power loss. There's no stalling, but it's as if I've hit a stiff headwind or the brakes have been applied and then release. It doesn't seem to happen when accelerating, but as mentioned above, it's most noticeable when maintaining a steady speed. Sometimes it'll be very quick like it's bucking and other times it'll last a full second or two. It'll do it in all gears at both relatively low speeds and highway speeds, so there's no pattern there. There is no check engine light when this happens, but I have not yet attempted to check codes just in case it might be storing any. It'll happen when the engine is both cold and at normal operating temperature. I've also tried to observe whether or not the tachometer drops when it bumps, but haven't really been able to discern that due to the usual momentary nature of the power loss.
The coil on this car is integrated into the distributor and I read somewhere that it's common for these to start to go as these Camrys age and accumulate a lot of miles. I also read that it's common for these cars to hesitate due to internally leaking fuel pulsation dampeners. The AC compressor makes a little noise, and sometimes it almost feels like what you would expect it to feel when the compressor kicks on, although the jolt or 1-2 second sustained power loss, depending on what occurs, feels stronger than that. Plus it'll do it with the AC off, so that doesn't seem to be a possibility. Other than this problem, the car has no issues whatsoever. It's quiet, uses very little oil, idles perfectly and maintains optimal operating temperature. The miles are about 75% highway since I've been using it mostly as an airport commuter car. Most essential maintenance items, such as the clutch, timing belt, water pump, oil seals, PCV valve, thermostat, radiator, motor mounts, etc. have been replaced within the last 15K miles, and most are Toyota OEM parts. Plugs, wires, cap and rotor have all been replaced within the last 10K miles, again with Denso plugs and wires, but aftermarket cap and rotor. I did feel up under the distributor and got some fresh oil on my fingers, so the o-ring might be leaking a bit. However, I don't know yet if there is any internal leakage inside the distributor itself.
I'm going to tear into it a bit, but I wanted to see which direction to look first. Would you suspect a spark issue (again, no CEL illuminates), or something more like a fuel delivery issue? I also wondered if it might be something like the TPS or perhaps a cam or crank position sensor on the way out.
View 10 Replies
1995 Geo Metro. 133 thousand miles. Loud rattle from engine, massive loss of power at lower RPM, low vacuum pressure, not blown head gasket (ruled that out), going to replace all vacuum hoses, advanced vacuum switch under distributor, and bypass catalytic converter, any other options I'm missing?
View 2 Replies
Ok I got a 1995 toyota corolla 1.8l dx .... So this is my back up car I went out started it up let it set and warm up and took it around the yard to run it a little well it ran fine then all of a sudden it lost all it's power well I finaly got it back to the drive that was only 50ft away took almost 30mins just to get it there. I cut it off let it sit started it back up and still no power well now it won't even start it has new plugs.. Wires.. Cap button.
View 17 Replies
I have a 1995 Ford Ranger 4 cylinder and the other day on my way home all of a sudden sounded like a lawnmower, it was very sluggish and would take twice as long to get moving,it also smelled like gas and I used a quarter of a tank in about 24 miles. Someone said it could be the ignition coils...
View 5 Replies
Already did the wheel to left, right and center about five times. Still no power steering.
View 8 Replies
This has happened before on my 98 ranger 2.5. You can drive it 10,000 miles without any issue and then all of a sudden you take off and there's no power but it quickly returns. Within the last year I've changed fuel pump assembly, fuel filter, injectors, cool packs, and plugs. Is it mass air flow? It seemed to happen a lot more after I cleaned it. My scan tool is amateur but it has a maf reading in lbs. What should it be while driving? Fuel pressure is always between 65-72 when I check it within specs according to my book.
View 10 Replies
So I got everything fixed on my 94 ranger so I thought. Now it runs right on the "L" on the idiot gauge on 90 degree plus days running the AC. Also it seems to lose power at times and not even want to do 70. I think new coils, new plugs and wires may work. I also have an intermittent check engine light that pops up on occasion, but clears when you kill the motor and start it back up. I was really starting to like this truck despite it not being my style(I like square body rangers) and it being a 4 cylinder. I like the MPG but am starting to think the 200k engine may be fading
View 14 Replies
So, a couple of months ago, my Ranger lost a lot of power going down the road, and when I came to a stop it died, and wouldn't start. So I got it started by roll starting it, made it to a friend's, and then back home. I've put new spark plugs and wires in, and it needed it, badly, but it didn't work. I got a couple of codes off of it,
P0302- Cylinder 2 misfire detected(which I fixed with the spark plugs)
P1443 - which I can't find a definitive answer for
P0500- vehicle speed sensor malfunction
P0171- system to lean (bank 1)
So, the truck will turn over, and if I give it a lot of gas it'll start at stay started for a few minutes, but then cut off. When it is running it's running very very very roughly.
View 1 Replies
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.
View 1 Replies
Background- 2000 Ranger, 3.0L 2WD 170,000mi. This truck is not my daily driver, i try to drive it once a week.
I've never had this issue before... I drove all over town yesterday; multiple stops, no issue. Today i go to do the same thing and upon accelerating out of the driveway i lose all power for about 3 seconds. I get power back for about 3 seconds then lose it again. This continues for as longs as i'm driving. Also, no CEL. I go back to the house to look things over, can't find anything staring me in the face really.
Truck idles fine and the issue is not present when i run up the RPMs in park. I've been reading some other threads about similar issues and most replies begin with checking the regular maintenance stuff i.e. TB, MAF, IACV, pcv, etc. It seems like a complete loss of fuel or spark...but only when in gear with constant throttle???
View 14 Replies
My ranger sounds like it's revving up real high when I take off but don't have much power. Know what this could be?
View 5 Replies
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies