Ford - Ranger :: 1992 - Tranny Slipping / Engine Revs But No Forward Movement
Jan 22, 2012
This is my first experience with auto tranny trouble so I'm a bit out of my depth. It started a few days ago. When you put it in gear and step on the gas, the engine revs, but no forward movement. If you keep giving it gas and rev it up, it will eventually grab and off you go. This happened around town after I took it to work last week when I went out for lunch.
When I drove it home, it slipped in and out several times in town, then by the time I got out of town (maybe 5 minutes driving) it evened out and didn't slip the rest of the way home (a 45 min drive). My assumption is that once it warmed up a bit that stopped the slipping. I checked the transmission fluid when I got back from lunch, and it was a little high. I drove it again today a week later and same thing only I didn't drive it long enough for it to warm up and stop slipping like it did the other day.
Other details: The truck is a 4x4, extended cab, v6 Ford Ranger with about 175k miles on it. I've had it about 1 1/2 years and its performed great up till now.
View 5 Replies
Advertisement
Will move if n 4low and give some rpm's. Reverse is fine, disassembled and clutches look fine.
View 1 Replies
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
View 5 Replies
My 4x4 4WD Ranger has a 5 speed manual tranny that locks up after going forward a few feet. It can back up all day long but locks up going forward. some god awful noises (grinding, clunking, etc) come out of that gearbox. the 4wd is electrically operated. the ? is , can this tranny be rebuilt with a kit? I'm having great difficulty finding a replacement. Are bronco II's compatible? Engine is 2.9L V6. On disassembly I found 2 meshing gears with broken teeth.
View 5 Replies
2000 X V10 4WD... 178K. Truck was not well maintained for most of it's existence. Drained both the TC and Drain pain and replaced the oil filter. Tranny oil looked like crude and a lot of tiny specs of metal - it shimmered in the sun... needless to say - I'm pretty sure it had never been changed.
Now - issues since I've gotten it done... Tranny has been slipping... I figured that I may not have filled it enough and after adding a few quarts, it seems to have stopped. Slipping was initially just when going from a stop.
Now it's having a problem where the engine dies when I shift from one position to another... For instance - from Park to Reverse, the engine RPMs drop as the clutch engages - but they drop from about 900 RPM down to about 500. And 50/50 chance the engine dies. Going from Park to Drive, the same thing but maybe drops to about 700 RPMs. Tried it in 2nd and 1st gear. Has happened in both. I've tried shifting to OD first before going to 2nd to 1st or vice versa and seems to behave better.
Should I flash the ECU and have it relearn the shift points? Did I overfill? Between the TC and Drain Pan - about 16 qts came out. I've been checking the dipstick - no frothing or bubbles. When running and in park - it actually shows low. Seems to drive fine once it's on the road. The engine cutting off when it's put into gear is really unexpected.
View 13 Replies
Reverse works great....engine revs and barely pulls in drive. Not sure yet if it actually changes gears. I am planning on replacing tranny. I have a few questions :
1: Could it be something more simple like a selonoid or ???
2: What all trannys will fit? this is the 2wd 5.4 liter xlt ...
View 9 Replies
I have a '05 V8 T-Reg (loaded with Air, NAV, and the like) and have the local VW dealership perplexed. The problem is when I am going up a hill and slowing down. While downshifting the T-Reg lunges forward while moving from 4th to 3rd gear or 3rd to 2nd. The car jumps forward and the engine revs. If I don't have my foot on the brake I would smack into the person in front of me.
Initially, the dealership (Day Imports, Monroeville, PA) determined it was the valve stems and replaced them (after keeping the car for 4 days). The problem came back and now (going on 6 days in the shop) they cannot find a solution. They tried a new shifter plate but the problem still exists. I'm waiting to hear back from the service manager about what VWoA should try next.
The T-Reg has 72k miles on it...
View 4 Replies
On the way into town, leaving a intersection lost all forward movement coasted to a parking lot. second gear would hold, drove home about six miles. When home put into reverse hear it go into gear , but slip. All other forward gears same, hear go into gear but slip, except second would hold. I think low fluid, or mechanical problem about 155000 miles. 2002 Mercury Mountaineer.
View 5 Replies
When the car is cold it runs fine. After driving for 10-15 minutes the transmission slips, while driving the engine revs and then engages again.I have only noticed the disengaging/engaging as speeds less than 40 MPH. When the car is in neutral and placed into drive it may take several seconds to engage which happens about 60% of the time. Could this be a sensor failure or time for a new transmission?
View 4 Replies
2004 Ford Ranger revs the engine when you engage the clutch then when you place it in gear it's like the cruises on it want to drive without you touching the Accelerator?
View 4 Replies
I've noticed when encountering a moderate hill at 60 mph in cruise the revs might suddenly increase from 2200 to 2700 rpm, then back down slowly as I crest the hill. If I'm in manual mode it stays in 6th gear, but almost feels like a downshift. I also feel no accelerator pedal movement. Is this a two stage intake at work?
View 3 Replies
Last week I noticed a slight "whomping" noise in my 2010 Ranger. Not a knock, not a ping, nothing that sounds metallic. Just a rhythmic whomping sound that only shows after the engine and tranny are hot.
It only does it in Drive or Reverse; and not in Park or Neutral. The tech at the dealership (30k on the vehicle) says he thinks it is a bearing in the torque converter.
View 7 Replies
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.
View 14 Replies
I have a 2012 Ford 4x4 crew cab 150 xlt. 15,000 miles. When pulling my dump trailer I was stopping to turn and the transmission disengaged. Once I turned the corner coasting the transmission kicked back in again. During this happening pushing the gas did nothing but rev up engine. My dealer said if this happened that a warning light would of came on or a wrench would appear on dash but it didn't. He said then it didn't happen. This happened 3 times in 10 miles of driving. I had it in tow mode.
View 4 Replies
Let me first say that my knowledge about vehicles is nearly non existent. Yesterday I was stopped at a light on a hill. When I pulled away up the hill it felt like the tranny was slipping real bad. I coasted into a gas station and stopped. I gave it the once over look around to see if I could see anything unusual. All looked ok, so I wondered if maybe it wasn't all the way into gear or something.
I limped it home only 2 miles and it was seemingly normal although I was real gentle and it was all flat or downhill. Later that night I drove it around the block and it was shuddering and banging and seemed to be slipping again. My question is doesn't the transmission usually go over time, or does it fail suddenly like this. Could it be something else? And lastly what does a rebuild cost. Truck is 06 FX4 54000 miles 3.73 gears. Edge Evolution on level 2.
I tow a Trailer a few times a year 7000 lbs fully loaded, if I do need a new tranny should I replace to a different gear.
View 5 Replies
Took my first camping with 2012 King Ranch F350 and 37 feet Challenger 12k fifth wheel trailer over the weekend.
I noticed there is lot of transmission slips in first gear. Once it enters 2nd gear, no more slips.
My previous Chev 2008 2500HD diesel didn't slip much with same trailer.
Is this normal for this F350? My rear ratio is 3.55. No slips without hauling.
Maybe I need to ask dealer to check 1st gear towing?
View 14 Replies
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 Replies
2003 Explorer with a slipping transmission...codes are P0731, P0732, P0733... Just had a new solenoid pack installed last week when O/D light came on and truck was clunking into reverse. Now, after new pack was installed the forward gears are slipping all over the place!
View 5 Replies
I have a 2002 Ford Ranger with a 3.0L engine that is having some issues with starting, here is what is happening.
Every so so often when the key is turned to start there is no movement from the starter motor. The battery is fine and all of the dash lights stay on while the engine is not starting. I have replaced the starter with a remanufactured model (possibly a mistake), and also replaced the clutch interlock switch.
I have attempted to change the ignition switch but the replacement I received did not even try to turn the starter (after many tries), like possibly it was faulty out of the box. I am currently using the OEM ignition switch as it will at least turn the starter eventually. I just worry that this problem will develop further at the wrong time.
View 7 Replies
I spoke with a few people here before about my 4r100.. it threw a code a month ago for P0750.. i replaced solenoid and it continued to do it even after clearing codes numerous times.. then all of a sudden it was perfectly fine for over a week, no codes, i ran a few brick hauls with it and ran it for over an hour straight.. i went to fl and upon return i took her for a drive and wouldnt you know, the code has returned.. i did hammer down a little but not from a dig, i just got on it a little playing with a neighbor and his truck and all of a sudden it did its thing slipping and not up shifting then the O/D started flashing again... i cant understand why the code would come back all of a sudden, there has to be a wiring problem correct?
View 9 Replies
I have a older minimax with the latest updates and have noticed that under full acceleration the tranny seems to rev up faster than the truck is accelerating. This occurs i think in 3rd gear like accelerating onto a on ramp etc. Kinda like its slipping if you know what I mean. I'm running the mild tunes in tow mode. Everything else seems ok.
View 7 Replies
