Ford - Mustang :: 1992 - Shaking And Won't Accelerate Past 40 Mph
Mar 24, 2016
I have a 1992 ford mustang 4 cylinder,its messed up bad.my car is shaking bad all the time and will not go faster than 40mph.what is wrong??
View 19 RepliesI have a 1992 ford mustang 4 cylinder,its messed up bad.my car is shaking bad all the time and will not go faster than 40mph.what is wrong??
View 19 RepliesI have a 2003 Mach 1 Mustang, ( 4.6 DOHC 32 Valve)....
When I start my car in the morning. Idling the car sounds normal and perfect with my SLP exhaust. But when I start to go on my merry way, when I’m in 1st and 2nd gear and I accelerate past about 2.8K rpm's. I hear a really quite noticeable pingy/tingy sounds from my engine (Yes sounding like that annoying AMMCO commercial with people making noises). This will continue for a little while when i get into my normal running temperature, the sound isn’t as "Loud" so to say but still present.
I can comfortably say that there is nothing loose within the engine compartment. My spark plugs are tightened to the proper amount. I experience no performance lost as well. This has just been a nuisance since I have purchased the car, it currently has almost 60k mileage and has followed the proper maintenance.
1992 Ford Mustang 5 spd 2.3l 4 cylinder. So a couple weeks ago, i got into my car and tried to crank it. I got one click then nothing. That's what I get whenever i turn the key. Not the repetitive clicking when the battery is low. After I found another ride home, I did some research and determined that it was probably the starter solenoid. I took a trip to Autozone and replaced the solenoid, but when i tried to crank it, one click then nothing. In order to get my car out of the school parking lot, I popped the clutch and got it running. Now, I'm stuck as to what the problem could be. I'm thinking it might be the starter itself, but it might also be the ignition switch.
View 1 Replies1994 E350 Club Wagon 351w, E4OD Transmission. New MLPS, New VSS, New TPS, New Fluid, New Filter, 5 year old Torque Converter.
The Transmission dribbled a little bit from the front pump seal a couple weeks ago, I checked the level, it was a bit low. Topped it off with Lucas, the dribble stopped. I drove it successfully for another week. I took it on a 10 mile trip, and 5 miles in, it started slipping above, 35mph, I let off the accelerator, and the transmission "Caught up" and I drove 35mph the rest of the trip. I let it sit over night.
The next morning it acted as if nothing were wrong. I drove it some more, and the same thing happened. I parked it, and revved the engine up a bit, and it tried to MOVE in park, I put it in neutral and revved the engine, and it lurched as if it were still in 1rst gear.
This time I let it sit for 24 hours, and after work I successfully put 20 miles on it without missing a beat. It was shifting right, good solid connection between the gas pedal and the road, and I thought the problem was fixed, as the temperature the day before was -20, and it warmed up outside to 30 degrees above.
I parked it for a couple hours and went to go do the errands, and it wouldn't make it above 15mph. It even struggled to do that much. I put it in reverse, and it held great, no slipping at all.
Let it sit until the next morning, and it was better. I pulled the Codes, and it gives me a 63(7) TOT High, and a 62(9) Torque Converter Clutch. It may or may not be relative, but Cruise hasn't worked in about 6 months either. What am I missing here? What could possibly causing this trouble? Fluid is up and new.
It's a 2004 4wd 4.6 v8 with 140,000 miles. My wife was driving around town today and had to park it at her daughter's house because even if you floor it,the engine will only rev to about 1500-1800 rpm's and idles really low,maybe 600 rpm. she said right before it started running bad,there was a bad smell. Also there is a humming/rattling noise that sounds like it's coming from the upper intake/throttle body area. I went and looked at it,tried to pull codes.
The check engine light isn't on and there are no codes stored in the computer. A couple of days ago,there was code po420 (Catalyst System Efficiency Below Threshold (Bank 1)and the check engine light was on. Engine was running fine. I cleared the code,and it never came back. I am not sure this is related,just trying to give all info possible.
My Mustang GT pings when accelerating up a grade of at least 3 degrees, beyond 40MPH. The pinging is reduced when I burn premium fuel, but it nevertheless still pings. I cannot drive beyond 50MPH over mountainous roads due to loud pinging which I am afraid will damage the engine. I have replaced the O2 sensors which were generating codes. No mechanic whom I have approached can tell me definitively how to eliminate the pinging. Otherwise, the engine, with its 144,00 milers runs perfectly.
View 5 RepliesGirlfriend has a '92 automatic. Transmission's been acting up for several months, periodically not wanting to shift into higher gears. Now, it will not shift at all after the first one, about 20 mph. Engine whines, but has power up to about 50 mph. Odometer states 64,xxx miles but don't know if accurate.
Need info on possible causes, other than total rebuild. Been reading about speed sensors, shift solenoids, control modules, as well as replacing fluid/filter and adding a treatment.
I have a 1998 Subaru Legacy Outback (automatic) that has 176,779miles on it. I live in San Francisco and only drive the car occasionally every 2-3 weekends out of the city. Recently within the past month I have noticed that after turning on my car and once it is in drive for the first 10-15 minutes it has a hard time getting past 20 mph. When I put the foot on the accelerator to go past 20mph the rpm goes way up to 4, 5 or 6. Once it gets past this then car is smooth and I have no problems. This problem seems to go away within 10-15 minutes of driving or if I turn my car off and then on again it seems to go away. I called my mechanic and they said it could be that the transmission fluid is low. I checked the level and it is perfectly normal.
View 2 RepliesI've had my 2002 Suzuki XL7 for 7 years and about 3 months ago, I noticed that as I go past 55 mph, my car creates this vibration that almost makes me think that it is trying hard to run.
Took it to the mechanic and they diagnosed after test driving and lifting it up that the wheels needed replacement. As it turns out when the car was running while lifted, the rear driver's wheel wobbled. The tires were fairly new, about 3 years old. They suspected some cord separation inside. I went and had all four wheels replaced but the vibration was still there. I took it back and they think rear differential is the problem, either the bearings need to be replaced or the whole differential axle.
The mechanic drained the differential fluid and showed me how it was almost metallic in color. The cost of replacing the bearings is $1100; to replace the whole differential with a used 88K miles, no warranty is $1400 and $1700 with warranty. What do you think is another possible diagnosis for it. I just did not want this to be another wheel incident where it didn't solve the problem. I heard that since it's a 4WD that it may be the drive train also.
My car is a 2005 1.8T Passat; About two weeks after replacing a burnt spark plug coil the vehicle started displaying EPC and a caution sign embedded in a circled arrow, whenever this happens i discover the vehicle does not accelerate past 80 mph even when the throttle pedal is pressed to the extreme; I replaced the engine speed sensor all to no avail, a used throttle body also behaved same way, what is responsible for this and how to rectify the problem?
View 1 Replies93 Mercury Cougar 3.8L V6 with just over 83,000 miles
l've been trying to figure out this issue for ages, but can't seem to find the root of the issue. When driving and accelerating to 40mph, the rpms drop and GET STUCK at exactly 1000rpm. Forcing the accelerator down makes the engine bog and sputter and not go any faster. No check engine lights whatsoever.
The idle is very rough and low in park (700rpm compared to the regular 900) and very low in drive (500 compared to 650-750). When stopped in traffic for a while, it begins to shudder and shake like it wants to stall right there. Now let me run down the extensive list of parts l've thrown at it, bringing only temporary results:
Replaced catalytic converter
Replaced IAC valve
Replaced O2 sensors
Rebuilt transmission (runs great, so l've ruled that out)
Replaced 1fuel injector
Replaced MAF sensor
Replaced motor mounts
Cleaned throttle body extensively
I asked a guy at a Firestone and he said that l needed a valve job. Asked another guy at another place, he said l needed a fuel system cleaning. Asked another guy under a tree, said l needed a new speed sensor. What could be the root issue? l was thinking carbon build up over 22 years maybe? Almost all 83k of those miles have been city miles...
This car is my baby, all l want is for it to be able to handle highway speeds without a hiccup. l'm keeping it and plan to see 100k hit the odometer and many more miles!
Okay I have a 2001 Vw Jetta 1.8t Wolfsberg.
I have done a few mods:
- Oil catch can
- Boost gauge
- New turbo (5000 miles old)
- Brake booster mod
- PCV system fixed and some hose deletes (that make the intake manifold have one line off of it rather than two)
- Timing belt/ pulleys
- Accessory belt / pulley
- A few other things but nothing to cause this
The car will do this randomly. And I mean once every two weeks of that. I will go to accelerate and the boost gauge says the "boost" is at zero and no matter how much I give it gas, it won't go past zero and stutters. But it stops almost as fast as it starts. I don't get it...
My catch can has 3/4" line to about 1/2" or so, that meets the oil catch can. (Ebay with the blue hose.) I have new plugs, all new (dealership recommended) lubes, all kinds of new small odds and ends. But it's never done this before. (3rd time now in a month..)
I have a 1995 Mustang convertible 3.8. Shakes when its started at an idle and as u push the accelerator, the shaking gets worse, in park, neutral, drive, doesn't matter. I have replaced plugs, wires, coil, torque convertor. I took it to precision auto tune and they said everything checked out computer wise but there is deffinately something wrong. Car shakes so bad its insane.
View 2 RepliesI'm driving a 97 Accord SE and it's suffering from a few issues that have me worried to say the least. For one, when I filled the radiator with water I noticed that it was cloudy/oily. Something was definitely in there with the water.
Two, I foolishly drove it thinking it would be fine. After 50 feet or so however problems started happening. I couldn't accelerate past 20mph. If I tried by putting my foot down on the gas nothing would happen but the RPMs going up. Each time I started the car I could go a little ways before pushing on the gas did nothing. Then I would have to restart the car in order to get anywhere with it.
Some background, I got my oil changed today after going about 1000 miles over when it should have been changed. Also, when it was scanned in the past the error code 0420 showed up. That has something to do with either the catalytic converter running rich or the O2 sensors above and below it might be broken.
I have a 2002 Chevy Impala driving it in the city of Chicago. It's recently had the oil changed, and the transmission fluid flushed and filter replaced. This car was mine before I went off to school, and I meticulously maintained it for three years, and then my step sister inherited it. She drove it for two years, and then it sat in the driveway for a year and a half. It's got about 175,000 miles on it.
Problem: Every time I start to accelerate past 25mph and get around 2000rpms, the car starts to give out, sputter and jerk. It starts to drop off right when it should be shifting to second gear. When on the highway, even if I floor the gas peddle, it won't accelerate normally, but instead just crawls slowly to higher speeds.
It will eventually reach the higher speeds, but it takes about 5-10 minutes for it climb up from 25mph. I don't know enough about this level of car trouble to make a diagnosis myself, and would like an estimate of the cost for repairs. Also the car is getting around 19mpg on the highway, which I need to improve if I'm going to survive the $4.50/gal of Chicago gas. I'm hoping that fixing this problem will take care of that as well.
I have a 92 Ford Thunderbird and it stalls every time I accelerate from a stop. I am a single parent and extremely low on funds. I don't have a mechanic that I trust so I don't know where to turn. How much do you think it would cost to repair? I also struggle when I don't have a car. There is no public transportation close to where I live.
View 1 RepliesMy 1992 Ranger has a 2.3L 4cyl 100hp engine with 207k miles. It occasionally hesitates when beginning to accelerate but never when at idle or when driving at speed. I don't even know where to begin. The engine has had consistent maintenance and runs well otherwise. This hesitation makes me afraid that it will damage the drive train somewhere. I'd like to at least know what the problem is even if I can't fix it myself because I've done most of the work on the engine.
View 3 RepliesI searched a lot but did not find these symptoms on my 1992 Aerostar 3.0 2WD with A4LD transmission.
In overdrive, accelerate to down shift, and the transmission goes out of gear. Engine revs as if it was taken out of gear. Manually shift to Drive, and it works fine.
Overdrive works fine if at speed, and works to shift up, but if going slow enough to drop to lower gear, transmission goes out of gear. Manually in drive, works fine.
I may have other symptoms, but this was on the way home from work, and I just parked it. I checked fluid level, and it was fine, still in the cross-hatch area of the stick, light colored oil, no smell.
I will replace the modulator and replace the filter, and see what that will do. If the overdrive works at overdrive speed, I do not see how that could be an overdrive housing failure that I have seen in many posts. I am aware of keeping track of the pin for the modulator.
I also have read that band adjustment is not a good idea. If they are worn that bad, they should be replaced. I don't think it is a band or clutch problem. I think it is a shift control problem. We will start with the modulator and filter and take it from there.
Have a 2004 Fx4. Lately its been shaking violently when i accelerate. When I turn the overdrive off it stops.
View 9 RepliesI just bought a used '05 F-150 and recently I noticed more a shaking I guess you'd call it. When I start from 0 to 80 nothing seems wrong, but when I slow down to coasting like 40 - 45mph and accelerate to 50 - 55 mph it shakes or acts like its having a hard time shifting or its skipping. And it doesn't happen till after I go past 40-55mph range and I've tried it in overdrive and out of it.
View 3 RepliesFord F150 1999 5.4 XLT... I've had this truck since may 2013 from the 2nd owner who only drove it
occasionally to make sure it ran. For the last 5 weeks there have been two occasions where my service engine light appeared...once on 12/28/15 and again today. Both read cylinder 4 misfire. Upon searching this piece which I'm assuming is the boot that covers or houses the spark plug is very unsecure and causes a shaking feeling as I accelerate or idle. Being so far back I can't reach it with extensions on a ratchet and barely fit my hand back there. Having to consider taking it into a shop for further analysis and repair but I'm trying to save as much money as possible as I am in between jobs since mid January. I have a picture attached...