Ford - Mountaineer :: 2006 V8 - Hesitation When Engine Is Placed Under Load
Jul 22, 2012
My wife has an 06 Mountaineer with a V8 and we have been having a problem with hesitation when the engine is placed under a load. The problem occurs most often when the transmission is in overdrive and the engine goes under a load such as driving up an incline at cruising speed. The engine begins to shudder much like a misfire but disappears when the trans kicks down a gear. The check engine light will flash momentarily but it never sets a hard code that I can read.
I have AutoEnginuity scan tool but there are never any codes. I've driven the vehicle with the scanner hooked up and there is never a misfire noted. The car has 96000 miles with, presumably, the original plugs. I'm aware of the potential problems with attempting to change these plugs. Where to look? I don't want to "hang parts" such as mass air flow or throttle position sensor. I've been hoping that the problem would progress to the point that a hard code would be set but none has yet.
View 4 Replies
Advertisement
Doesn't happen all the time but when it does it is obvious at 45 mph. Not there at no load on engine. No code shown.
View 8 Replies
How's it going? I have a 2005 F150 with the 5.4L V8. It has 70,000 miles on it and until yesterday and has been a great truck. While driving in traffic yesterday the truck started running rough and hesitating. It through two codes - misfire cylinder 5 and misfire cylinder 6.
In response, I purchased two new coils and 8 new autolite plugs. The plug installation went smoothly and the coils all went on without incident. However, this didn't fix the problem!
The next day I found that cylinders 5, 6, 7, and 8 were all having issues. At this point I also had an "O2 stuck lean" code so I pulled the plugs and found all four brand new plugs fouled and smelling like gas and an ehaust that smelled like raw fuel. This led me to replace the O2 sensor on the drivers side. With the new O2 my lean code disappeared but I still had a rough idle.
Further troubleshooting found that injector 6 was stuck open (which presumably fouled my O2 causing it to read lean and dump fuel thus fouling all the plugs on one side). I replaced the injector and the rough idle disappeared and all seemed really well as the truck idled in my driveway.
However, as soon as I hit the road I noticed a major hesitation. The motor is also noticeably louder and has a very hard time accelerating. I'm thinking that I've plugged up my cat by dumping so much fuel in to it and the hesitation is caused by a lack of breathing - does this sound possible? How would I confirm this without replacing the cat? Anything else I should look for? I'm fairly confident I have combustion in all 8 cylinders now so I'm leaning towards intake/exhaust issues.
View 13 Replies
First, a little background on my truck. 2007 with 5.4, 122000 miles, oil changes with 5-20 Motorcraft and Motorcraft filters, plugs done by dealer 40000 miles ago. The truck has developed a ticking noise, kind of like a lifter (I know these engines don't have lifters) that is most noticeable from the side of the truck near wheel. ticking speeds up with the rpm. Also around same time, between 40-55 under load there is a bit of a stumble, but I can gas thru it. I'm guessing these are related. I'm thinking spark plugs again, but shouldn't I get more than 40000 out of them? I might just take it in, since I've got oil leak somewhere around back of the oil pan, but figured maybe might get some clues first. Also, no CEL.
View 4 Replies
I have a 2005 F150 with the 5.4L V8. It has 70,000 miles on it and until yesterday and has been a great truck. While driving in traffic yesterday the truck started running rough and hesitating. It through two codes - misfire cylinder 5 and misfire cylinder 6.
In response, I purchased two new coils and 8 new autolite plugs. The plug installation went smoothly and the coils all went on without incident. However, this didn't fix the problem!
The next day I found that cylinders 5, 6, 7, and 8 were all having issues. At this point I also had an "O2 stuck lean" code so I pulled the plugs and found all four brand new plugs fouled and smelling like gas and an exhaust that smelled like raw fuel. This led me to replace the O2 sensor on the drivers side. With the new O2 my lean code disappeared but I still had a rough idle.
Further troubleshooting found that injector 6 was stuck open (which presumably fouled my O2 causing it to read lean and dump fuel thus fouling all the plugs on one side). I replaced the injector and the rough idle disappeared and all seemed really well as the truck idled in my driveway.
However, as soon as I hit the road I noticed a major hesitation. The motor is also noticeably louder and has a very hard time accelerating. I'm thinking that I've plugged up my cat by dumping so much fuel in to it and the hesitation is caused by a lack of breathing - does this sound possible? How would I confirm this without replacing the cat? Anything else I should look for? I'm fairly confident I have combustion in all 8 cylinders now so I'm leaning towards intake/exhaust issues.
View 5 Replies
I have a 2008 Passat Komfort Wagon with the 2.0T. At 40,000 miles, yes it only has 40,000 miles, the thing started hesitating and misfiring on me only during heavy load. I ran the codes and it said #4 cylinder misfire. The check engine light was only on during the time it was misfiring and hesitating. Took it to the VW dealer to have them run it again and get guidance and they verified the #4. When I picked up the car the CEL was illuminated. They said it does it when it misfires. I explained that it was not on when I dropped it off and they basically said tough cookies. So I replaced the #4 coil pack and all 4 plugs. CEL light still on, but wasn't misfiring. Next day it began misfiring again under heavy load. Took to Autozone to run the codes and now says misfiring on all cylinders.
View 6 Replies
2 wks ago I was running down I95 at about 95-100 mph (basically floored) in a rush to get somewhere on time. Since then my truck has been running for crap. It threw the p0171 code when I checked it. When driving under normal conditions it pings a lot and my mpg is down about 3 mpg and has this hesitation when you get on it. Even when you accelerate at a normal rate it surges a little, it pings a lot and has a loss of power, about 30-40%. It feels really sluggish and doesnt want to pull and then you will feel it starting to pull a little harder then it starts to surge/hesitate a little again.
Truck has 147k on it. I was having a similar situation until I had the plugs replaced at 125k, so I figured the plugs shouldn't be the problem. So I replaced the fuel and air filters, cleaned the maf w/maf cleaner and Throttle body w/tb cleaner and replaced the pcv with a new one from ford. Still pings bad under load and still has the hesitation/surging and crappy fuel economy. Its running smoother but no fix yet. This is crazy trying to pinpoint this issue. The detonating isnt crappy gas because I used super and it still detonates quite a bit.
Its a 06' F250 5.4 3V XLT Lariat SC FX4....
View 14 Replies
Our Camry has about 105,000 miles on it. Car is well maintained, I change the oil every 3 k or so and the air filter is clean (although it is not a factory air cleaner- it is a K&N filter). Other maint is done as specified by the warranty/maintenance book although the car is long out of factory warranty.
We occasionally pull a 800 lb pop-up tent trailer and just got back from the Sierras after driving up some pretty tall passes with it. Car ran great, got great mileage, temp gauge rock steady. I say this because it is probably the most stressful driving we do with this car. While we live in the city we are retired and the car is not exposed to constant heavy traffic, dust or snow. Mileage seems to have remained pretty steady, even with the hesitation.
Got home from the mountains and a couple days later the car began to hesitate when under load. The hesitation shows up as a slightly uneven surge when the car is going up a hill or when it is cold. About 20 mph the car seems to momentarily stop accelerating, then evens out and upwards of 40 mph I don't feel it at all. The hesitation is getting a bit worse over the last couple days in frequency, but still isn't felt on the freeway. I don't know if the hesitation is related to the recent trip to the Sierras.
I hooked up my OBD II computer to see if there are any DTCs, none shown, even left the computer on the car for a day to see if anything might pop up when the car surged, but the computer isn't seeing trouble codes.
My other thought was "got some bad gas", ran the tank out and put in new gas, fuel injector cleaner and dryer. With one new tank it hasn't worked. I haven't replaced the fuel filter yet.
Tried driving the car in 1st and 2nd gear only and found that the hesitation isn't dependent on what gear I'm in, but seems to be more about the speed and load. In neutral, slowly revving the engine, I don't detect anything that sounds or looks like a hesitation (just watching the tach).
Been reading about problems some Toyotas have had with unintended acceleration but I'm not sure that is my problem. I have to admit I didn't know that my Camry was "drive by wire" and maybe I don't understand it enough. Maybe a "reflash" might be needed?
My sense is that I should go ahead and do the next major maintenance items including plugs, but if I had a bad plug or plug coil wouldn't that show up as a Diagnostic Trouble Code item?
Could this be a bad injector or fuel filter? Wouldn't they produce a DTC? How do I break down the next steps?
View 12 Replies
I bought a cheap golf in february. It's an akl engine (1.6sr). Everything was fine on the way home. The car then wasn't used for like a month or two, and was stored outside. When we started using the car it gradually got more and more stuttering. At first it was just a slight stutter when accelerating, but now it's horrible. It will stutter and hesitate like crazy when accelerating or under load, but will cruise just fine at normal rpms. So far I have changed the air filter, fuel filter, spark plugs and a bad spark plug wire, but nothing has worked. I bought a vag scanner but couldn't find any codes. The idle isn't too bad but not perfect. What the problem can be?
View 10 Replies
So I have had my 02' Camry for a little over a year. Love the car, it is a 2.4L SE with a 5-speed manual. Recently it has developed this mystery misfire/hesitation under a load and at idle with the AC on. I replaced the plugs with OEM Toyota Iridium and it seemed to clear it up for about a month, but now has come back. If I start the car and turn on the AC it will intermittently start to miss but not only when the compressor is engaged and it does it every now and then under a load specifically in 4th or 5th gear under a load with lower RPM's (under 2000).
The check engine light is not on and hasn't as much as even flashed on at any time so there must not be any hard misfire codes. I want to stop by Autozone and see if they will scan it to find any stored codes but haven't had time. I would think that if it was a coil pack that it would be a hard misfire. I'm stumped. This car is in great condition...no oil leaks, interior is near perfect (replaced a worn shift knob, and door panel pieces around the window switch). Also car has 160k miles.
View 9 Replies
My 2003 Camry loses power and starts to hesitate or miss-like under load, but when cruising along not under load it runs smooth. There is no check engine light coming on.
I have changed the fuel pump and fuel filter in the tank.
I have changed the spark plugs.
I have added injector cleaner and fuel treatment to the fuel.
I have cleaned the air filter and air filter compartment.
View 7 Replies
1997 200 SX SE coupe. It has the 1.6L engine and is a 5 speed.
I recently purchased this car and it had the CEL or check engine light on. The part store stated the codes were: P0304 X 2 and P1445.
Here is my problem that occurs mainly once the engine is warmed up- it started bucking and hesitating whenever I push the gas pedal. It doesn't do it when the engine is cold- at least it is very slight and hard to notice. On the highway at constant cruising speeds the car rides and purrs great. While I'm idling at a red light the rpm is constantly dropping about 100 rpm every second.
I have tried the following:
-Replaced distributor cap. The cap was slightly corroded.
-Tested spark plug wires by applying then to metal and looking for spark.
-Did a dry compression test and all cyl ranged from 150-160 psi. (Good levels??)-
-Sprayed carb cleaner around manifold to see if idle changes - nothing
I am fairly a novice at mechanics so I'm still learning. Perhaps the car has stale gas? Not sure how long it has sat, or even if it has been sitting. bad injector? Bad fuel pump/ filter?
View 5 Replies
Today I drove my 2006 G2 Prius with 59,000 miles to the park and had the windows down. I climbed a hill for a good while that had the engine under load and there was a concrete wall beside me, and I could hear a very very faint metallic-like rattle. I mentioned it to my partner who listened and said he couldn't even hear it, so maybe it is just me.
View 2 Replies
I have a '07 Sonata GLS with the 2.4-liter Theta engine and the 4-speed automatic. It has 52k miles on it and has always been serviced regularly. It's been a pretty decent car but is starting to feel a little tired, most notably the worn/bouncy suspension.
Anyway, the other day I was driving down the highway and gave it a little gas to pass a slower car. Doing 60 MPH it downshifted to 3rd (~2000 to ~3300 RPM) and I thought I heard a noise in the engine bay, but I wasn't sure. I ended up needing more power so put it to the floor and as it kicked down to 2nd at ~5000 RPM the rattly noise got a lot more pronounced. Driving around normally I don't hear it but any time I put it to the floor (merging/passing) I will hear the rattle. I can also hear it if I lock it in 2nd gear and give it full throttle up a hill at low speed, like you might do with a stick shift.
It seems like it only does it under load because if I rev it to ~4000 RPM in park in the driveway, there's no noise, even at full throttle. I know the V6s had tensioner issues but I haven't heard much about the 2.4s. I'm not super concerned as it is still under warranty but what might be wrong with it as this is my first Hyundai vehicle, especially in case the dealer can't replicate it.
View 9 Replies
I have a 2006 sonata with a 2.4 . It has 120,000 miles on it right now. Around 100k miles , when the engine is under load(hard accelerations), the top end of the engine starts clacking,like the rockers arms are loose. It also does it when in park and you rev it up above 3000 rpm then let off the gas. I have not had time to pull the valve cover yet.
View 1 Replies
I have a 2006 GS300, just took it to the dealer as the VSC light came on and had engine hesitation. After checking them out, I was told that the engine needs to be rebuilt. I was informed that due to carbon built up on the manifold is causing the problem. How is it possible for a car with just 88K miles to have this problem? Should I had them recheck? Perhaps a sensor?
View 1 Replies
Ok, got a hesitation when the engine is cold, almost feels like a miss. Dealer could not find anything and there are no engine codes. They wanted to replace the plugs with new platinum plugs. I said did you pull any plugs, not that is what the tech said it could be. Could it be the Mass air flow sensor? Or a coil. After a mile or 2 it is fine. I switched to shell premium since dealer told me I had to get a decarbonization from using cheap gas. I used exxon regular and BP regular with a treat of premium every few tanks. But now I am on shell and they said I needed another decarbonization, This is getting rather expensive, I may go back to my local mechanic once the warranty is out. But the hesitation puzzles me.
View 2 Replies
Today I notice a very hard when down shifting and later on the engine started to hesitate and stall, RPM up and down. Accelerate by itself. I was able to drive home but engine light for exhaust system fail. VW is going to tow car Monday morning. 2006 2.0t Car only has 21k miles.
View 4 Replies
Horn just stopped working on my 06 mountaineer. 20 amp fuse is good. All other controls on steering wheel work fine (sound system, cruise control, no airbag problem). Also, when I press panic button on remote FOB the exterior lights flash until i press it again but no horn. Any thoughts?
View 5 Replies
I have a 2006 mercury mountaineer awd v8 which up until a few weeks ago would be able to get 22 mpg highway. I have noticed that recently it has been around 17 mpg at the same speed. Could all of this be blamed on winter gas blend, or is there more to my problem?
View 6 Replies
I have a 2006 azera limited 63k miles on it and I'm getting a rough idle that sounds worse when the weather is cold. also when I press the gas there is hesitation from the car to accelerate. on top of that, I feel vibrations from the engine all through the driver and passenger seat. When I turn the car on it idles at 1300-1500 rpm and takes about 5-7 minutes to come down. when it does , it idles at 650 rpm. I'm not getting any check engine lights or codes. I've replaced spark plugs, air filter, had the air induction service done at the dealership, and had to have Hyundai put on a new throttle body last march when it gave out on me while at work. the dealership doesn't know what it is and said to use a fuel additive when I fill up the tank. I have and am waiting to see if that does anything. I put in a bottle of CRC 1 Tank fuel system cleaner 2 days ago. I've even changed my brand of gas from exxon to bp just in case. I think it may be a bad hose for the idle and a bad motor mount for the vibration. Could an O2 sensor be going bad?
View 1 Replies
