looking to replace the front wheel bearings on my 06 Mountaineer. Detroit Axle? I found them on both ebay and amazon and prices almost seem too good to be true (under $100, 12 month warranty).
View 6 RepliesI gotta a roaring noise coming from my right front while turning. Planning on replacing just the wheel bearings tomorrow & not the whole hub assembly(2008 2wd). Is there a thread that lays out the steps and other parts I may need? I've seen alot different stories on the net on how to do it. Everthing from I can press new bearings to I have to do 4x4 hub conversion. Seems to be some confusion.
View 2 RepliesMy 2005 Prius has 95k miles on it. I've been hearing a cluck-cluck-cluck noise from near the front driver side wheel. I had an independent mechanic test drive it, who said the wheel bearing needs replacement. Should I have it checked out by a Toyota dealer? They're so much more expensive, but are is it worth taking it to them?
View 15 RepliesIn 30 years of wrenching on cars, I've never encountered this problem. Replaced the pads and left rotor. Rotor is typical Chinese rotor. While there, replaced the wheel bearings. Also knocked out the races (with a brass drift) and replaced the races with the ones that came with the new wheel bearings. The bearings are NAPA bearings. Packed the wheel bearings just like always.
Applied some grease just like always on the spindle. Put it all back together. Tightened the wheel bearing nut while rotating the rotor in the opposite direction. Went to maybe 10 ft lbs. Backed the nut off, set it firm finger tight. Installed the cotter pin. Got a whole bunch of sloppiness in the wheel bearings. I can feel a LOT of it when rotating from the 6 o clock and 12 o clock position. What did I miss? NEVER had this happen before. 2002 f 150 2wd
4x4 1999 Ranger ... They are a squeaking and driving me crazy. How hard are they to do, do they need a press or can they be done at home?
View 7 RepliesI've been having a lot of noise coming from the front left tire, and I finally had it diagnosed as a bad wheel bearing today.
I noticed that the front wheel bearings are sold individually while the rear wheel bearings are sold as hub assemblies. Is there a certain way that the front wheel bearings have to be removed and pressed on? I'm trying to see if this is a DIY repair.
If front wheel bearings can be greased through the abs wire hole on a f250 4X4, will that work on a sealed bearing on a gm product? I have done my f250 but I also have a 2004 suburban.
View 2 RepliesI have a 2000 F350 4X4 crew cab and have a vibration in the front end. I have done sone investigating and have come to the conclusion that is the front wheel bearings. The dealers says I have to buy the entire hub assemble but I seem to think different. But if I can replace the bearings any special tools that might make it easier ..
View 14 RepliesFront wheel bearings making noise. Can I buy replacement bearings/races/seals, or must i buy a whole new hub front assembly?
View 3 RepliesI have some whine coming from my front wheel bearings so I'm going to replace them both. I'm not sure if this had been done on my truck before, but I'm thinking so since I have Moog greaseable ball joints.
Truck has 250k miles on it. I'm going to check the pads, rotors and slide pins. Anything else that might need work? I'm sure the half shaft could use a once over, but I don't keep my hubs locked so they don't turn much in regular driving.
Are just the bearings serviceable/replaceable or is the only option to get entire wheel hub assembly?
View 14 Replies1984 K2500 4WD 8-lug
Front DS wheel hub. The front wheel bearing nuts come loose all the time. I have to check it every weekend, usually starts to get loose after a week and I have to pull apart the hub and re-tighten the nuts. Bearings are all okay, but tires wobble when they get loose...
Reverse order of install: nut -> keyed washer -> nut -> washer -> snap ring -> 4wd auto engaging assembly -> spring seat -> cap seal -> spring -> cap
My understanding is the deepest nut gets adjusted so that the bearing is tight enough that nothing wobbles but not so tight the wheel can't freely spin. Then the keyed spacer goes in and the second nut is tightened down hard to lock the first nut in position.
I've had on-and-off issues with the front DS in general as well. That side the brake caliper always start to suck in air after a few months, on #4 now. Brake system has been replaced with rebuilt MC & calipers, all new lines and warning switch. Also the 4WD doesn't seem to lock in on that hub every time. It will engage, but doesn't hold if it gets too much torque. Then other times it engages and locks and won't have any problems until next time I want to use it. It works about 70% of the time. I've taken it apart and checked everything, no burrs or wear that I've noticed to cause it.
I just got a new Sonata and I find the car has a noise like bad wheel bearings in front, it sounds like driving on really rough pavement.. I have changed the tires and still get this..
View 1 RepliesOur 2011 w/140,000 miles has a variable front end noise that I suspect from past experience with other vehicles is a bad wheel bearing. I've seen posts of the procedure for replacing the Gen 2 bearings that requires the hub and bearing be pressed out and new bearing back in which would limit the DIY'er, but looking at the replacement parts diagram for the Gen 3, it appears that the hub and bearing unit is bolted in with 4 bolts and may not need a hydraulic press to install.
View 4 RepliesReplacing front wheel bearings on my 99 Passat? There is a gentle 'wahwahwah' grumble at speeds over 40mph. The car has done 130,000 miles and is otherwise in nice condition.
View 3 RepliesI have an '06 F-250 that's making a quiet grinding/humming noise from what sounds like the front end. It doesn't seem to be coming from any side in particular, just an omnipresent noise whenever the truck is moving. It's constant with speed, and most noticable between 30-60 KPH.
Truck has about 268,000 KM on it right now, and has been worked pretty hard for whatever that's worth as well.
My wife drives a 06 Mountaineer last spring a left front brake caliper piston seized up and there was damage to the rotor I replaced both rotors and that left front caliper then I changed out the rear pads as well . Then ever so often before that the ABS light on the dash would pop on hit reset it wold go off now it just stays on.
Then a few weeks ago she said the little yellow lines that indicate you are in all wheel drive started to flicker on .. Have not a clue as to why that is on now . But I would told most code readers would not read these sort of problems that I needed to get it to a dealer..
I drive a 2006 Volvo V50 with 65k. Recently the car started making a noise and the dealership told me that I need new front wheel hubs because my bearings are shot. The car has always been well within the weight limit, has never been through deep water (we do line in the pac NW so there is a decent amount of rain), and has had complete service at all of the maintenance times. I think that under 125k bearings should not be giving out and that volvo should replace the bearings for free - the mechanic is telling me that there is no set time for bearings to wear out - it can happen at literally any time/mileage/age and it would not be the company's fault. Who is correct?
View 10 RepliesIs it possible to replace the main bearings in a 2001 Escape 3.0 with the engine in the vehicle?
View 1 RepliesOur 2002 Mountaineer with AWD started to have a clunk noise in the front driver side wheel area. It happens only when you take you foot off the gas between 30 and 65 MPH. If you slowly ease up off the gas no noise you have to totally remove your foot from the gas. It sounds like something needs grease or like a gear is a little loose. I have seen some post about noise but have not found one that happens in this situation.
View 3 Replies2009 accent sedan has had an issue with noisy front hub bearings? I had my Accent in for an alignment today and also had the shop check for a humming noise that seemed to be coming from the front end. The humming varied with speed. The technician said it was a noisy hub bearing. He said that the bearings were both tight and had no play in them. I was told just to monitor the noise, as the bearings were tight. Just had the transmission fluid changed too. (Used genuine Hyundai fluid) The noise doesn't seem to be transmission related, as the transmission shifts perfectly with no noise. Also, the level of the noise changes on turning the wheel in either direction.
View 3 Replies