Ford - Mountaineer :: 1998 V8 5.0 - Shaking At 40 MPH / Slightly Rough At Idle
Sep 17, 2012
A couple of days ago (Friday, Sept 14th), I noticed my 98 V8 5.0 liter Mountaineer was idling rough. I had the codes pulled and got P1401, P0455 and P0308. I did find a vacuum leak and fixed it (changed the air filter and cleaned the MAF while I was in there). I also replaced all the plugs (based on the P0308 misfire). I cleared the codes after that with a neg battery pull.
I'm still running slightly rough at idle, but not as bad. However, I have found that when I get up to about 45MPH (1500 RPMs) I started to get a worrisome shaking/ vibration. It's difficult to tell where it is coming from. If I let off the gas, or give it more and go up to about 50 mph, the shaking stops. It is only when I'm pressing the pedal in this range (like it is having trouble switching gears, perhaps?). Over the past two days of driving it and testing, I have been to autozone and had the codes checked. Nothing comes up, and no CEL.
I just had a new trans put on about 6 months ago. The only thing that preceded this issue was I got an oil change the day before this started at a place I don't normally go to (unlikely, but since they didn't write the type of oil they used on my window tag, I figured I'd mention it). I've read some suggest it to be a tire issue; but that strokes me as odd, since the shaking only happens when applying gas.
View 14 Replies
Advertisement
98 5.0 last week i was driving around for a few hours and everything was fine. Did some work in the garage for a few hours and had to run to the hardware store. Started the truck up and she ran like crap. Engine shaking like a misfire. First thought plugs and wires. Well by then it was late and Easter was the next day didn't get to it till Monday. Well after the change still crappy running.
So I changed the fuel filter and cleaned the mass air. No change. Checked for spark on the coil packs all have spark. Checked the PCV all good there. Checked for vac leaks none found. During that I noticed a small hole in the EGR tube I repaired that but still running like crap backfiring out the exhaust, engine shaking badly at times. I also changed out the FPR on the fuel rail. No change of course.
As of today I changed the coil packs. Again no change. Only code it throws is a EGR high flow after I fixed the hole but was having problems before that.
View 10 Replies
From cold, I start the van up, and if I just slightly crack the throttle it will start running rough. I think it goes away under heavier throttle...might just be that the rpms are up I can't feel it anymore, I don't know. It will idle just fine, and after it warms up it also seems fine. Where to look?Also I sometimes hear a very small, high pitched, vacuum leak from under the hood. What are the most common items that go bad, that I should look at first?
View 4 Replies
1998 Ford Escort SE ... On idle ( at a red light or in park while on) it shakes terribly. When I shift into N it will lessen for 3-10 seconds, but then it will cycle back to the vibrating. The spark plugs were replaced about 4 months ago and got a brand new transmission 5 years ago this coming summer. It came into the family in '00 and I got it when I turned 16. The vibration started about 2 years ago and at first I was told "little car has shaky engine". When it got worse I was told it was the motor mounts, which I replaced a year ago. When they were first put in the car ran smooth as ever.
My mother turned on the AC while I was taking her for a test ride that same day and it started back shaking. They said the motor mounts were perfectly in place, and that it was a broken fan blade. My husband and I just don't see a fan blade causing that much shaking. I can hear the car violently vibrating when I park and take pizza to someone's door. Also a more minor problem, ever since we put new brakes on, my brake light comes on too easy. The weight of the peddle will turn the light on, and I have to keep using my foot to pull it up after each time I touch it, and sometimes when I'm driving.
View 12 Replies
I have a 2011 XLT 5.0 V8 with 133,260 miles. I have extended warranty for the next 12,000 miles...which is great because I drive about 400 miles a month... Anyhow it runs great but for one small issue (hopefully) that has been intermittent.
She likes to idle slightly rough in drive at a stop or very low speed, and in reverse at slow speed. If I don't maintain the RPM it will stall and the low oil pressure light will come on, which I imagine comes on because of the sudden stall.
I first noticed this while backing into my garage in the driveway, It would fluctuate in RPMs and if I didn't maintain the gas it would shut off. I took it to the dealer and all they were able to tell me was the Tranny fluid was low and it would cause it to shut off at incline because a sensor isn't detecting fluid in the tranny. I thought this was weird but being as I have never owned an F150, I didn't know better.
It was fine for a little over a month and it started doing it again at stop lights and backing into my driveway. It has become frequent but there is no issue driving at speed and on the freeway. There is no stuttering or shaking and if it weren't for the fluctuating RPM at a stop and the stalling, it would be hard to tell if there was an issue.
All I can note is that there is a clicking sound under the hood, if I remember correctly the last time this happened I was at a 1/4 tank of fuel like I am now, I also feel like it may be a throttle body issue, or some sort of air sensor, I plan on taking it to the dealer but I figure I would get a more informed answer on the forums.
I also hear this is a common issue with the 5.0s... I purchased the truck in December and since then I have only put 250 miles on it.
View 3 Replies
I changed all of the brakes on her car yesterday, test drove it, everything was great. Put close to 100 miles on it w/ no issues. Therefore, I don't think it's anything I did.on her way to work, the CEL came on. The car has a rough-ish idle, and jerks slightly in low RPM. I went to Pep Boys and got it read. it threw 8 codes:
P0171
P1130
P0300
P0301
P0303
P0305
P0442
From what i've read, the p0171 is the system is running too lean and p0442 is a leak somewhere. The 300s are cyl misfires.I don't want to go replacing every conceivable part. What these codes mean in conjunction?
View 14 Replies
I have a 14 GT base with manual and I've been noticing at idle (sitting at stop lights...foot on or off brake and or clutch...in or out of gear) it has a bit of a rough idle or stumble during the first mile or two...then its fine. It doesn't feel like it will stall and if I tap the gas I do not notice any difference in throttle response. RPM needle stays steady... is the just something that is normal? It doesn't bother me a lot... just noticeable. All that aside, except the occasional lifter noise at cold start (not always...which is odd) all is good.
View 6 Replies
This is my first new car, but I am assuming the idle should be pretty smooth. I feel my idle and it feels sort of rough. Almost like there is a slight misfire but not that intense.
One more question, car burning oil?
@ 7500 miles I was down a little more than a quart and now @ 14,100 I am down almost a quart. That is slightly alarming.
View 1 Replies
Owner of a 2014 350 fsport here.... 15,000 miles ... I noticed on cold starts a slightly rough idle since its gotten colder here recently. After starting the car it'll start fine and everything but then as its warming up the needle sometimes jumps 75-100 rpm. its like someone tapped their foot on the accelerator and let off. no lights or anything and the car runs fine.
Heres the catch... i have a joe z catback and joe z intake with fsport filter, could this possibly be why? because of the airflow ? i also have been using Lucas fuel injector cleaner and lubricant.
Also when i put the car in park after driving, i notice the needle isn't steady, it does move a little maybe 20-50rpm, not sure if this is normal or not because i never really paid attention until now.
View 2 Replies
My 2011 Elantra has a slightly rough idle at stop lights. It doesn't happen ever time, and some people probably wouldn't even notice it, but at every few/several stops it idles a bit rough. When I recently had it in to Hyundai service for the ECM update, I asked them to take a look at it. Of course, they couldn't replicate it at the time, so they couldn't do anything to address it directly. The service manager asked if it happens when the A/C is on or off. While I didn't know the answer at the time, it seems to happen with it both on or off. He did say that the ECM update may address/fix the issue, but unfortunately it didn't. While it's not a big problem, it's a minor annoyance I'd like to get fixed (as I need to enjoy my ride at all times.
View 220 Replies
I have a 1998 Lincoln Town Car with about 350,000 miles on it. This morning I sensed a slightly rough idle when I started it up and let it sit in the driveway. While idling I plugged in a scan tool and after a few minutes it showed a P0306, a misfire in cylinder 6. I know there could be a few causes of this but my past experience has been a bad ignition coil (this car has the coils on each plug).
Over the years I've had 3 coils go bad, all giving the same rough idle symptom and P030x, where x was the cylinder number. Replacing the coils solved the problem each time.
So this morning I assumed it would probably be the same. On my way to the auto parts store (4 miles), I monitored the computer, it kept throwing a P0306 (cylinder 6) and I kept clearing the code. About 2 blocks from the store, the car seemed to be running a bit rougher. When I pulled into the lot, I got a P0307 code (and no P0306). Hmm. Well, I bought a new coil and replaced coil 6. I then sat in the lot and idled it and after a few minutes it threw the P0307 again. I cleared it a few times and it came back.
I assumed there was about 0 chance that a second coil could go out within minutes of another (assumption from a car tinkerer, not a professional), so rather than buying another coil, I drove it home to do some further testing. On the way home, it kept throwing the P0307 and nothing about P0306.
So at home, I swapped coil 7 and 5, idled it for a few minutes, and, sure enough, it threw a P0305 (the problem had moved to cylinder 5, following the coil). This indicates to me that I had 2 bad coils?!?
So my question is whether it's possible, or even common, to lose two coils at virtually the same time. I should also point out that before today I did not notice rough idling and there were no computer codes set. I also thought maybe it's possibly a problem developing with an ignition module (but I'm not sure if my car even has one).
Anyway, it was late and I have not replaced the second coil. I did do a couple other tests. I measured the resistance on the primary of the new coil, as well as 5, 6, and 7 coils. They were all close to 0 ohms. The resistance of the secondary ranged between 5k and 8k depending on the coil. Out of curiosity, I also did a final swap of the original coil 6 with the "faulty" coil 7 now in 5 (follow me?) and it still throws a P0305, indicating both the old 6 and old 7 coils are, indeed bad. Another note is that both "bad" coils are about the same age (maybe 150k-200k miles on each), so they're not newer ones.
Does this all make sense? Should I go ahead and replace the other coil and see what happens, or should I check something else?
View 12 Replies
I have a 2008 Ford Focus - 4 Door Sedan SE 60300 miles.
I've gone to 3 mechanics now and no one can seem to figure out whats wrong with my car. Here's whats happening:
About 1 1/2 years ago I took my car to get an oil change at Jiffy Lube (Yeah never again). When I left, my car was idling funny... Silly me didn't take it right back and have them tell me what was wrong.. so I let it go, well about a month later it started idling even weirder. Basically it feels like my car is shaking when it gets under 1000 RPM and I notice my RPM dial start falling and bouncing back, acting like its going to stall, but never does. I notice a loss of power when this is happening (on speed up and just accelerating in general). All of this is random, I can't seem to put a pattern to it as to when it happens. One day I'll start it up and everything is perfect... Then I'll shut it off and restart it later, and it starts vibrating and puttering again... No signals as to if its hot/cold or wet/dry, no environmental variables seem to cause it to happen anymore than others. And there is no check engine light on, everything "looks" normal.
What I've had done to it so far is:
Air filter changed / reseated
3 oil changes (keep getting told it will work)
Throttle cleaned
Computer reset for idle sensor data rebuilding
Now I'm told that I need new engine mounts, and that could be the reason for the vibration. I'm thinking that the vibration caused the mounts to wear out, more so than the mounts being the cause. Mainly because I don't see how bad mounts could cause loss in power/bad idling.
What could be wrong?!? Really bugging me and don't want to keep throwing money at it for phantom solutions. Seems like mechanics I go to can't figure it out unless there is a check engine light on with some diagnosis code to tell them exactly whats wrong.
View 8 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 1 Replies
I'm having a problem with my 6.0 back in September I started to notice a little miss with some black and white smock while accelerating so I took the truck to a power stroke specialist near my house to have it diagnosed they said my number 5 injector was starting to go bad so just this last week I finally got up enough money to get the injector changed I got the truck back yesterday from the mechanic. While driving I get a lot of shaking right around 1500 to 2000 rpms when I let off the accelerator it smooths out if I mash on it and keep the RPMs above 2000 it smooths out the truck still has a lot of power no check engine light has ever been on through this whole ordeal and there's a rough idle I guess the best way to describe the shacking would be if the truck was a standard shift and you were pulling a hill in to hi of a gear.
View 6 Replies
Recently bought a 2001 Accent that has been experiencing a 'rough idle' for the last few weeks. Basically, after I've driven the car for a few minutes (from a cold engine position) and then stop at a stop light or stop sign, I can hear the engine get louder and the car starts to vibrate slightly, after I've driven for about 15 minutes at higher speeds and then stop again I can actually see the steering wheel shaking when I take my hands off of it. If i put the car in park when I am stopped and the engine is on, the idle calms down quite a bit. The weird part is that when I first start driving the car in the morning, the rough idle problem doesn't happen until about 5 minutes of steady driving - so when the engine is colder I don't experience the problem, The problem is not that serious, and Ive already brought it into a dealer who cleaned out fuel injection, gave me a major tune up and replaced all the spark plugs, but the problem still persists. I am gonna bring it back to them but they seem a bit lost to be honest. Other than this the car is driving normally when I am not idling.
View 14 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 7 Replies
I got a p0284 code and have some symptoms such as shaking while accelerating between 45 and 60 mph and a rough idle.
View 2 Replies
Got a strange one here. 1995 Buick Park Avenue, supercharged 3800, 159K miles... an older car, but an unmolested one. A little over a week ago I began to notice an occasional miss when cruising along at highway speeds, along with a slightly rougher idle. Both the fuel filter and the plugs/wires predated my ownership of the car (a little more than 6 months); so seeing no obvious culprit, I replaced them and hoped for improvement.
Unfortunately, neither had any impact. The missing continued to become more noticeable. It was never present under acceleration. Most of it was like a split-second long version of "bucking" that could be observed while cruising at lower (<2000) RPMs. It was also very noticeable at idle. Eventually a code was set: P0341, camshaft sensor issue. If the story had ended there, it would have been just another night in the garage. But it didn't.
As I was noticing the aforementioned symptom increase, I also noticed my voltmeter would occasionally "twitch" in the downward direction. Eventually I had an incident where I came to a stoplight... transmission in Drive, foot on brake, gauge dropped to around 10-11v. It returned to 14v momentarily, but dropped back down, held there for several seconds, returned, etc. No particular rhyme or rhythm. Of course my first guess was that the alternator was failing; a separate problem from the other.
I checked all the relevant connections (at the battery, at the alternator, etc), and cleaned them for good measure. All were tight, relatively clean, and the cables showed no resistance on the ohmmeter. It happened that I had another correct alternator on hand (used/working pull), so I swapped it in. No change. I reinstalled the original and was back where I started.
On my most recent drive, I noticed both issues had become very noticeable. The drop in voltage was happening at nearly every stop, and the missing was happening a few times per minute while coasting along. There seemed to be some correlation between the missing and voltage fluctuating, but it wasn't absolute.
I decided to attack the voltage issue again. Re-checked all the cables; same result as before (all OK). Looked all over the car for possible bad grounds, loose connections, or other visible problems, but found none. My next thought was to run a jumper from B+ to the voltage regulator's Sense input (have seen issues there on more than a few older vehicles) - but after reading that this car uses the PCM as the voltage regulator, I didn't proceed.
Just to be certain I'm going to have the alternator tested by the local auto parts store. But I suspect it'll pass.
View 8 Replies
2001 f250 7.3L, 289,000 miles, changed the IPR and ICP, noticed the EBP tube was in two pieces. Would this cause the rough idle and shaking? IT started running rough and would die after a mile or two. Would have to wait 30 minutes before it would start again. That is when a buddy told me to change the IPR and ICP the ICP plug was covered in oil as well as the top of the ICP. So I changed the wiring plug as well. I originally cleaned and changed O-rings on IPR but then it wouldn't start, bought a new IPR and started but runs rough. I just started it with EBP tube removed and sensor unplugged. Idling rough when I press accelerator and RPM go above 2K it levels off pouring black smoke everywhere.
View 3 Replies
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 Replies
I have problem with my 2006 Prius , idle shaking and when the engine stops its really rough.
View 2 Replies
