Ford - Mountaineer :: 1998 5.0L - EVAP Coil Removal
Jun 3, 2015
How to remove this thing????
View 2 Replies
Jun 3, 2015
Advertisement
Ford - Mountaineer :: 2002 - 3rd Row Seatback Removal?
How the seatback comes off of the 3rd row seat on an '02? There is a spring or something protruding from the seatback on the right side towards the bottom. I'm afraid it's going to stretch or poke a hole in the leather. I think if I can get the back cover thing off I can reach up under and fix it. I don't know if it's a spring our of place or what.
View 2 RepliesPrius (Gen 2) :: Warning Lights Came On After Replacing Evap Coil
After the tech changed the evap coil (9+ hours) I have 4 instrument panel warnings.
Brake system warning light
Master warning light
SRS warning light
Hybrid system warning light.
Even though they saved me alot of money I need to bring the car back for day two and have them figure this out.
Ford - Mountaineer :: 2007 - Transmission Lines Removal?
OK, replacing the radiator in my 07 Mountaineer. Watched the U-tube video and purchased the sprecta model recommended. Instead to messing with the release on the lines I opted to remove the nut from the radiator. Easy enough, everything going well until I find that the new fittings on the Spectra are a different size. Now I have to remove the lines from the old connect. Bought the Lisle 39660 tool for Ford lines. I've been fighting with them most of the afternoon. I cannot get them off, tool slides in all the way, won't budge. How to get them off, I don't give up easy....but, all my knuckles are banged up.
View 2 RepliesFord - Mountaineer :: Overhead Console Removal To Replace Burned Out Map Lights
I am working with a 2006 Mountaineer Premium with rear heat/ac, sunroof, and Homelink. I need to remove the overhead console to replace burned out map lights. I cannot determine how to remove the console.
The shop manual has instructions for 2 styles of overhead consoles but not the one in this vehicle. Those 2 styles have a sun glass or garage door opener compartment that you open to access some screws.
This console has the map lights at the front, the controls for the rear ac/heat in the middle, and a panel for the sunroof switch and Homelink buttons at the rear. There is no room for a compartment that opens.
I can get the front portion loose by pulling it down off the clips. The back seems to held in by screws. I do not want to apply much force to avoid damaging anything.
Ford - Mountaineer :: 1998 - P0153 Code On / Off Occasionally?
I have a 1998 Mercury Mountaineer AWD 5.0L V8. I've been getting the P0153 code off and on for about 3 months.
I read on another forum that bad gas caps can cause the problem, well, I've replaced the gas cap with a new OEM one and that seemed to stem the tide a bit.
As it often seems to pop back up when the tank is 1/4 or less, I fill the tank, and that works some. But it still happens.
This Thursday, 2 days after I changed the spark plug wires, it began misfiring on the #6 cylinder and the P0153 code came back and stayed on.
I swapped the #5 & #6 plugs, cleaned up the area and reinstalled the wires with dielectric grease. No more misfire, but the code did not clear.
So, I also changed the O2 sensor that kept kicking off the code. I used the OEM, Bosch O2 sensor.
I started it and it ran beautifully. Next day, I was driving and that damn code came back. I stopped and had breakfast, it was gone.
Off and on all the rest of the day, disappearing even while I was driving
Ford - Mountaineer :: 1998 - How To Replace The Burnt Out Dash Lights
Easy to follow instructions on how to replace the burnt out dash lights on my 1998 mountaineer? I almost bought a new mountaineer; however, I decided to keep this one. It's been very good to me and it's paid off.
View 2 RepliesFord - Mountaineer :: 1998 V8 - Driver Door Lock Not Working
I have a 98 Mountaineer V8 AWD... The other day the power door lock on the drivers door quit working, even with the remote it wont lock the doors. If I press the other door lock buttons, the one in the rear and the other on the passenger side door, all the doors will lock. I have tried to chase down the wire ( pink with Yellow stripe, or green stripe, I forget which one it is now ) I don't have a wiring diagram to know where the wire goes.
I have even swapped the door lock buttons from side to side and it still didn't change anything... Is there something that is a common problem with these that I need to know about??? Looking for a wiring diagram of the doors?? There is no power going to the drivers door lock, but there is to passenger door. I am thinking of running a jumper wire from door to door and see if this will fix it...
Ford - Mountaineer :: 1998 - Disable Automatic Headlights Feature?
I would like to permanently disable the automatic headlight feature on our 98 Mountaineer. I do not want them to come on automatically or stay on after the vehicle is turned off.
There is a switch located on the mirror. It does not work. This is the mirror that it has. I do want to retain the automatic dimming mirror feature. Is it possible to jumper the switch inside the mirror?
Ford - Mountaineer :: 1998 V8 5.0 - Shaking At 40 MPH / Slightly Rough At Idle
A couple of days ago (Friday, Sept 14th), I noticed my 98 V8 5.0 liter Mountaineer was idling rough. I had the codes pulled and got P1401, P0455 and P0308. I did find a vacuum leak and fixed it (changed the air filter and cleaned the MAF while I was in there). I also replaced all the plugs (based on the P0308 misfire). I cleared the codes after that with a neg battery pull.
I'm still running slightly rough at idle, but not as bad. However, I have found that when I get up to about 45MPH (1500 RPMs) I started to get a worrisome shaking/ vibration. It's difficult to tell where it is coming from. If I let off the gas, or give it more and go up to about 50 mph, the shaking stops. It is only when I'm pressing the pedal in this range (like it is having trouble switching gears, perhaps?). Over the past two days of driving it and testing, I have been to autozone and had the codes checked. Nothing comes up, and no CEL.
I just had a new trans put on about 6 months ago. The only thing that preceded this issue was I got an oil change the day before this started at a place I don't normally go to (unlikely, but since they didn't write the type of oil they used on my window tag, I figured I'd mention it). I've read some suggest it to be a tire issue; but that strokes me as odd, since the shaking only happens when applying gas.
Ford - Mountaineer :: 1998 - Oil Coming Out Of Rear End Vent Tube
My 98 mountaineer keeps throwing rear end oil out the vent tube.. Why does it keep doing this?? its been doing this for a while and had to change an axle seal, I think because of this. It stopped doing this for a little while after I changed the seals and put in new oil.. Its not over full.. When it stopped I figured it was because the oil was old and was foaming or something.. But now its back to doing it again... The tube is not plugged.. Why does it keep doing this???
View 3 RepliesFord - Mountaineer :: 1998 - Running Rough / Engine Shaking Like A Misfire
98 5.0 last week i was driving around for a few hours and everything was fine. Did some work in the garage for a few hours and had to run to the hardware store. Started the truck up and she ran like crap. Engine shaking like a misfire. First thought plugs and wires. Well by then it was late and Easter was the next day didn't get to it till Monday. Well after the change still crappy running.
So I changed the fuel filter and cleaned the mass air. No change. Checked for spark on the coil packs all have spark. Checked the PCV all good there. Checked for vac leaks none found. During that I noticed a small hole in the EGR tube I repaired that but still running like crap backfiring out the exhaust, engine shaking badly at times. I also changed out the FPR on the fuel rail. No change of course.
As of today I changed the coil packs. Again no change. Only code it throws is a EGR high flow after I fixed the hole but was having problems before that.
Ford - Mountaineer :: 1998 - Driver Side Door Switch Not Working?
The driver side door lock switch on our 1998 Mercury Mountaineer was no longer working. I replaced the switch with a remanufactured unit and it still doesn't work. The rest of the switches and keyless entry work as intended. Is there another likely reason besides a bad switch that would cause this? Which pins on the back of the switch should have power on them? Also, how do you test the switch?
View 8 RepliesFord - Mountaineer :: 1998 - Takes Some Extra Cranking To Start / Idles Like Missing
I have a 98 Mountaineer, 5.0 auto that I just picked up. It takes some extra cranking to start it, and then when it does start it idles like it's missing. Also, the throttle response is not good. I have two codes that come back as soon as they are reset. P0340 (cam shaft sensor) and P0350 Ignition coil malfunction. I have been reading threads here saying that sometimes the P0340 can be the alternator it not always the sensor.
View 7 RepliesPassat (B5) :: 2004 - Spark Plug Coil Pack Removal?
2004 passat 1.8t. How do I remove the coil packs on the top of the spark plugs, so I can repalce the plugs.
I unclipped the wire and unsure how to pull the coil pack off.
No bolts. can turn it and maybe pull, but doesn't budge and don't want to break.
Camry :: 2007 V6 - Wire Unseated From Connector During Ignition Coil Removal
Any easy solution to reseating this wire in the connector? It got yanked out by accident when i was removing an ignition coil under the wiring harness. 2007 camry v6
View 3 RepliesChevrolet - Prizm :: 1998 - CEL Emissions Evap System Code Comes Up
Check engine light emissions evap system code comes up when the system is scanned what could be problem? 1998 chevrolet prizm...
View 4 RepliesS-10 :: 1998 Blazer - P0507 Idle Speed High / Low And P0446 Evap System
I have a 1998 blazer 4x4... I had a issues with the car before and I had to turn the idle screw up until I fixed my problem. I now fixed my problem and I need to know what my idle rpm should be at.
After I fixed the original problem after about a day of driving I had a P0507 Idle speed High/Low. I turned the set screw down and lowered my rpm. After about 5min of driving the code went away on its own.
About 1 week later I am now getting the P0507 again and now it has a buddy. P0446 Evap System.
Questions what would my idle rpm be? Can the high rpm cause the EVAP code as well.
Oldsmobile - Aurora :: 1998 - Codes P0300B Misfire And P0440B Evap Emission
I have a 1998 Oldsmobile Aurora with 103,000 miles. I'm receiving the codes P0300B Misfire and P0440B Evap Emission.
I use Premium Unleaded gas (not at a cheap station) so I don't think it's the gas causing the misfire code P0300B. Also I've put on a new gas cap but I still get the Evap Emission code P0440B.
Working on a 1998 Oldsmobile Aurora with these 2 codes?
Lincoln - Towncar :: 1998 - Replacing Front Coil Springs?
I am going to replace front coil spings on my 98 town car. Do I really need OTC 7045B tool to remove springs?
View 1 RepliesPassat (B5) :: 1998 - Cylinder Won't Fire / Ignition Coil Is Not Being Activated
I have a 98 1.8T passat. The number one cylinder won't fire, according to my checks, the ignition coil is not being activated by the CPU, (no current at the connector only ground) what could cause this problem. Any way to check the crank or cam sensor.
View 2 Replies