I was using the method of spraying starter fluid around the intake and found a pretty significant vacuum leak around the throttle shaft on the drivers side. The carb is a 2 barrel holley. What are some different ways to seal a throttle shaft vacuum leak? Could I take it apart and seal it with a plastic O-ring for now?
View 2 RepliesSo I was was tired of trying to tune my Holley 650 and finally threw in the towel and got a 600 Edelbrock. When the holley was on there the engine had the slightest surge but I was never able to pin down a vacuum leak. The PCV valve made quite the racket while running.
Now the edelbrock is on there and no matter what I did I could not get the idle below 750 (4 speed truck). I checked the carb, manifold, hoses, and boosters and no vacuum leaks. I disconnected the PCV port at the carb and plugged it and it immediately stalled.
I went down to the local speed shop and got a new PCV grommet that has a small opening (restricting) and some foam filter material in it. Got home and popped it in and the idle dropped right down to a near stall. Adjusted the screw and she's running fine.
Now for the question. Did I fix the problem or just band aid it? Has anyone heard of having to restrict the PCV circuit?
I have a vacuum leak on the driver side seal on the changeover rod in the intake manifold. It was replaced recently at the dealer and now has another hole in it. I was told this is caused by oil in the lines and my pcv valve is bad.
View 1 RepliesHow can I find a vacuum leak? I hear hissing from driver side. I used 2 cans of starter spray and on throttle cleaner. No change in rpm.
I'm on the of my Latin. If I pull the throttle short and raise the rpm I hear a loud air soak. But I can't locate it. Can be the egr, lower intake upper intake or fuel interceptor. I begin to hate the car.
Trying to track down an air conditioning problem. Seems like a vacuum leak somewhere is screwing with my AC and shutting it down upon giving it any throttle (hills etc). Where should I look first or is there a certain area that is prone to leaks?...truck is a stock 1993 F-350 460/auto.
View 1 RepliesLong story short, I have a small vacuum leak in the 4wd system. I disconnected the lines going to the hubs to prevent grinding them to pieces as they are brand new. This, of course lock the front hubs in and disengages the X-fer case in 2wd.
It is not engaging in 4wd unless I select it, so I don't imagine it hurting anything in the X-fer case or anything. Other than the extra rolling mass, is this okay to operate at until I resolve my vacuum issue, provided I close all openings and places for trash to get in?
I just picked up an 85 6.9L today and took it for a good drive about 60 miles. it ran flawlessly but on the way back it started smoking a lot. I popped the hood and the head on the driver side had puddles of a blueish tent liquid, Ibelieve to be diesel but the color has me confused. Where this could be coming from? also. with the intake disconnected the truck smokes out the intake after being shut off. is this normal?
View 7 RepliesI have an Accel Gen vll EFI setup on a 59AB and plan on using a pressure regulator but it has a vacuum inlet fitting. I'm assuming it's to allow for more pressure on acceleration. When the vacum drops more fuel will be allowed into the fuel rail is my guess.
View 3 RepliesI had the universal joints replaced on my 1999 Ford Ranger now it vibrates badly starting at 45 mph and when I coast at 65 mph the vibration is very significant. The mechanic does not know what is causing this. I never had this problem before changing the U-Joints and I have 171,000 miles on the truck.
View 4 RepliesSince the 2150A was computer controlled it has no ported distributor vacuum advance port, correct?
If you have a distributor with vacuum advance and a 2150A carb, where do you connect the advance to if not the carb?
2005 PSD 6.0L Excursion ... I suspect that have a fuel leak at the fuel line fittings near the driver side cylinder head. (I believe that it is fuel, since it is so clear, I guess I should collect a few drops and see if it burns vs. coolant.)
It appears to be at the junction of the fuel lines. This is the point where the fluid drops off the tubing and falls down. The clip that holds the two tubes together at the joint is very dirty, the one below them is clean. The tag on the line that is at the joint leaking is part number 3c34-9j338-ag. Is there a o-ring in side the joint? Do I need to replace both hoses of the joint? I can't find any posting of a history of this fuel line leaking.
Or... is it that the joint never fail, and the leak is up tube? I can't see any where it is coming out when viewing it from the top.
I've experienced a fuel leak, I've checked all over, and the only thing I've came up with so far, was maybe its coming from the banjo bolt going into the front of the driver side head.. I cant really get to it good enough to tell though..
View 6 RepliesI picked up a renamed 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. Are these parts still produced and if not is there another way to make it work?
View 10 RepliesI picked up a remaned 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. I can't find anyone who carries it, let alone knows what it is. Are these parts still produced and if not is there another way to make it work?
View 13 RepliesI recently had a Jasper rebuilt engine installed in my Ford E150. Since than my check engine light keeps coming on and the computer is saying my cas air mix is "lean". The instaler says i need a new fuel pump.Another mechanic says it is more likely a vacuum problem.I know it's possible that the fuel pump is bad bur since this has just started since the install, I don't believe it can be the fuel pump unless it's just one hell of a coincidence.
View 6 RepliesI'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister, there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one. It's a 2007 Ford 4x4 6.0 diesel.
View 2 RepliesI have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 Replies4601 DBP, just under 35k on it. At idle, i hear a slight whistling almost like squeaking. I took it to my independent tech and he showed me that if he removed the dipstick for a second while idling, the noise stopped, due to lack of vaccuum, so he believes its in the pcv system. I am still under powertrain and obviously federal emissions 8yr 80,000. Go start your R and listen at idle inside the car for a whistle or squeaking noise that seems like its inside the passenger dash.
View 13 RepliesI recently purchased a used 1999 F250 Super Duty with about 150k miles on it. The truck runs great and I have no complaints but there are a few things that need to be taken care of. It looks like there is a very small fuel leak where the filler neck ties into the rubber hose that runs into the fuel tank. There is a thin film of diesel along the side of the tank, on the leaf spring, the air bag and various other places. Nothing is dripping. I want to drop the tank and replace the hose. The Haynes manual says to depressurize the whole fuel system--is this really necessary if I don't plan on doing anything to the system aside from dropping the tank?
View 2 RepliesI just rebuilt the Autolite 4100 on the 390 in the 62 T-Bird I just purchased. Starts up and idles great, but when I apply slight throttle, the motor shuts off. If I apply a lot of throttle quickly, it picks up fine and drives with no problems. No sputtering, or backfiring. I just slightly apply the throttle, the RPMs drop, and the motor cuts out completely. Starts right back up when I turn the key, but does the same thing, at any temp.
I originally thought it was a vacuum leak, but checked what few vacuum lines there were, with no leaks to be found. Hooked up my vacuum gauge and it read at a steady 15psi.
New mechanical fuel pump, haven't checked the fuel pressure yet, but I installed a see through inline filter, and it's filled up and pumps fine.
Timing is at 8 degrees, and vacuum advance is hooked up to the only vacuum line in the carb. New cap, rotor, plugs and wires.
I adjusted the idle mixture screws down until the idle dropped, then turned them out a half turn (I've read on here it should only be a 1/4 turn, so I'll adjust that later today). When I was messing with the carb yesterday, I noticed the inlet check ball retaining screw was leaking a bit of fuel, so I went over the carb and checked all the screws and tightened down what needed it.
When I rebuilt the carb, I left the original needle & seat assembly, since they were in great shape, and the ones in the rebuild kit were much smaller. The choke plate needs to be adjusted, as it doesn't open up all the way at full temp, but the engine did the same thing with the plate held open all the way open.
I've gone through everything else I think it could be, so I'm figuring it's the carb. This is my second carb rebuild ever (first was a Motorcraft 2150) and it went smoothly, and I double checked the floats and measurements.
My truck has developed a bad habit when it is cold (as in outside air below freezing and engine cold): The accelerator pump arm rubs against the throttle arm hard enough to bind the throttle partially open (NEVER a good situation!). I've removed the carb and verified that everything "looks" right:
1) The throttle shaft is in the right location and doesn't have any side to side movement.
2) The accelerator pump arm pivot is straight
3) The accelerator pump arm is straight (It's design makes it a bit difficult to just "bend" the arm side to side and I shouldn't have to do that anyway...)
4) The throttle arm is straight
After taking the arm off and straightening it out (repairing my attempts at a "field" repair...), verifying the linkage and then reinstalling and adjusting the AP, everything was working perfectly on the bench (kitchen table...), so I went ahead and reinstalled the carb (always fun at 10:30pm when it is 7F outside and the freaking wind is blowing at 30mph!).
By the time I got everything bolted down and hooked back up, the carb had cooled off a LOT, and the linkage was once more binding. I have no doubt that if I bring it in and let it warm back up, it will work perfectly.
So, what could be the problem? Do I just need to say the heck with it and hit the side of that lever with a file to get the cold clearance it just doesn't have? I can't imagine that this is a common problem with Holley 4160 carbs...