Ford Fuel System :: Huge Stall / Lag And Sometimes Backfire
Dec 6, 2008
My 302, only mod is a 4160 600cfm and i love it. But when I kinda baby the throttle and the secondaries flop down to let fuel it... There is a massive lag time. Sometime it will even backfire! fronts have 59's (could be slightly richer) and the back has a 134-39 metering plate and a black spring. it seems that it needs another shot from an accelerator pump to keep going. I raised the float with the same result, how to cure that lag time without mashing the throttle.
View 14 Replies
Advertisement
I have a 79 ford and a 400 engine that i put a 1411 on and it backfires when you hit the gas it is worse when you drive it then when it is just sitting there.
View 4 Replies
Truck is a 74 250 390/auto tran. 2wd. When I am at a stop and then step on the gas (not hard) it will sometimes backfire then die. Then I can start it up and it'll run fine. The only other times it backfires is if I am doing about 40 or higher, take my foot off the gas, and let it coast down to around 33mph or so then step on the gas it'll backfire once and run fine. If I am at a dead stop and punch it it will also do some backfiring, usually killing it.
Other than these times it runs fine. I've adjusted the carb (I know not correctly) and that does work if I set the idle higher. Is it possible my fuel pump is going bad? I was always told a mechanical fuel pump pretty much either works or doesn't. If it is a possible pump problem should I test it or just replace it...
View 2 Replies
I have an ambient temp switch connected to the vac port on my throttle emissions control solenoid for my 2150 carburetor. It's a 78 F-150 with a 5.0L 302, automatic 2WD. Would a bad ambient temp switch screw up my idle? I've disconnected the vac hose and it won't idle at all, and it does the same thing when I disconnect the two wires from the ambient temp switch. If I leave everything alone, I can get the idle down to around 1800rpm, but any lower than that and it stalls.
Is it possible to swap out this throttle emissions control solenoid with another type? I've looked everywhere and can't find an exact replacement, and I have no instructions on how to tune it.
View 4 Replies
I have a motocrap 2bbl on my 73 f-100 all stock 390 when I drop it into gear she wants to sputter and stall without warning at idle runs great but put a load on and forget it what is wrong with this thing?
View 4 Replies
Looking for a good diagram of the complete vacuum system on the AEB 1.8t 99 passat. I am throwing a 1136 code which is indicated as a "Manufacturer controlled fuel and air metering". I recently finished a complete rebuild and engine is finally back in but running in limp mode. During the rebuild, I used mobil 1 synthetic as an assembly lube for all internal components including valve train.
I immediately wet fouled O2 sensors and spark plugs. After repeated removal and cleaning for plugs and O2 sensors i have progressed beyond seeing the "wet" fouling but plugs are still very rich, black in color but dry. Engine starts and runs at idle(lumpy) consistently and will run for as much as 5 minutes but very rich. If i rev engine to 3000-3500 rpm it will "POP" or backfire and immediately stall.
View 5 Replies
I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
View 8 Replies
I have a 2015 PRIUS C for 3+ months now (used to drive a 2012 PRIUS) . Approx 3K+ miles traveled already to date. Anyway, I noticed on 2 occurrence that my MPG on the odometer view has had a huge reading fluctuation. Prior to the first occurrence, my Travel A was somewhere around 46MPG and it closely matched the Odometer view reading. Then I noticed it go down to 33MPG while Travel A is still at 46MPG, both had the same miles traveled. I let it go and when I checked my MPG on the Odometer last week, it was back to normal.
View 6 Replies
I went to move the 2000 yesterday and it will not start because the gas went bad. It has been sitting about 6 months, since it did not snow this past winter. How do I go about cleaning the fuel system? I was thinking suck the gas tank empty with an electric fuel pump, and blowing out the lines with air. Does this sound right?
View 7 Replies
I have a ford focus (2004) 4cyl 2.0 L. One day, the car would stall only moments after the engine would turn. It would just shut as if fuel was ceased. I could however rev the engine and keep it running if I had my foot on the gas. After awhile, I tried again and it worked! Everything was normal, then it stalled after trying to start if up again. So this was intermittent at the time.
So, I swapped my fuel pump relay with the a/c one- and it fired right up! I'm thinking great, its just the relay and not the actual fuel pump. So went to the parts store, got a relay, and (me being me) wanted the new relay in the original fuel pump relay plug in the fuse box. As I was taking it out, a really really small piece of plastic chipped off of the plastic cover of the relay, and fell in one of the slots where you put the relay. How in the world?? I couldn't get it out. So I ended up putting the relay in anyway, and my car has the same problem originally (stalls), but now I have these check engine codes: p0460 and p0463
I also noticed, its running really rough when I hold the gas now. Could the plastic piece that fell into the relay be causing a strange short from my fuse box? Or, could it be my fuel pump this whole time? If its messed up because the plastic, Is finding a fuse box at a junkyard and replacing it feasible?
View 2 Replies
This van has had a couple of fuel pumps, no surprise there, and i need to look through my paperwork and find out how many miles the current one has on it, but it has the STRANGEST habit I've ever had on any vehicle. Starts fine, runs fine, no fuel pump noise when van is running, and when you turn it off, the fuel pump creeks on and off for several minutes.
I mean a strange creaking noise almost like a shorted electrical device or a vehicle's brakes when you park it on a hill and the breaks creak as it settles into place. I'm probably doing a lousy job of describing this but i don't know how else to describe it!
ALSO, if you lay under the van and wait til it stops creaking, you can tap the bottom of the tank and it will creak for a few more seconds. You can tap repeatedly and make it creak more. Is it about to explode? Can i trust it on a road trip?
View 6 Replies
I have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 Replies
What would make a FI engine act like its flooding out and dying after a short run on the freeway?
Details:
1994 F-350 351W (just overhauled this winter)
has new TPS, ICM(?).
Dual exhaust dumps right before the tires
new filters in tanks, new fuel filter on frame rail
All fuel lines have been opened and blown out from the tank to the engine compartment fitting near firewall.
Fuel pumps hold good pressure when tested.
Symptoms:
smells like its running rich most all the time
after a short hiway run @ 70MPH it will stumble and die when returning to surface streets.
fuel smell near engine sometimes, but no obvious puddles or leaks anywhere.
May be related?:
When on a longer highway run, I can't use the FWD tank for a long period without the engine stumbling and cutting out or popping at times. But I can swap to the rear tank for a bit then run the FWD tank again for a while. driving up hills it seems to be worse, but I'm in the panhandle of TX right now..good grief!
I am having to drive this truck for work long distances. While I dont expect a vast fuel range, it would be nice if I could go a couple hundred miles on 20 gallons of gas....
View 9 Replies
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
View 2 Replies
I have a 95 F150 4x4 reg cab long box with a 302 V8 and dual tanks... I was driving around yesterday when my truck started to lung and then the motor stalled... when I stopped moving I tried starting the truck and it started with no problem, so as i kept on my way, about 5 minutes later the same thing happened and it stalled again, (I have an automatic by the way). but this time before it stopped moving i pump the gas a few times and it fired back up and then stalled again... i switched from my front take to by back maybe thinking it could me my fuel pump in the tank but it did the same thing again about same time later... Would it be my fuel filter on the frame (like in line fuel filter) or why is it doing that? its EFI by the way.
View 14 Replies
My vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
View 3 Replies
2002 E-250 with the 4.6 V-6. Pulled the 30 amp fuse, replaced the fuel filter, replaced the fuse, now the truck wont start. Checked the fuse and the kill switch under the passenger kick cover, all ok. Cranks and cranks but wont fire. No problem prior to changing the filter. Even swithed out the relay with another, no luck.
View 4 Replies
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 Replies
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
View 4 Replies
My '90 E250, open road, mini motorhome , says on the radiator mount , that there is a Fuel shutoff switch that may have been activated.... I don't have the manual for it, so I need finding the switch, so I can reset it ....The vehicle sometimes starts after about 2 mins with the ignition on, but today won't start, even after a longer wait. Both tanks are full...Fuel gauge not working , in either front or rear position. I can hear the rear pump,in the tank, but can not hear the front one....When I bought it last year, it ran fine after waiting to start, and both positions worked , no stalling , or shutdown.Came home about 95 miles, and it's been parked almost all the time since. I want to start it up weekly , but am having that same problem ...Today was the first time I could see the Fuel Pump Shutoff warning ...but can 't find the darn switch to try resetting .....
View 1 Replies
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 Replies
