Ford Fuel System :: Fuel Filter Is Clogged When Turn Over The Engine
Jan 22, 2017
Is it fair to assume that my filter is clogged when I turn over the engine and fuel does NOT come out of the filter with the uphill line disconnected. I was able to disconnect the rear line from filter and fuel DID pump out of line when I cranked it over. Been dealing with a crank no start, I'm in the process of trying to test my CPS properly but not sure if I'm testing it right.
2000 f 150 4.2 v6 232,000 miles....
View 7 Replies
Advertisement
I'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister, there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one. It's a 2007 Ford 4x4 6.0 diesel.
View 2 Replies
I have a 95 F150 4x4 reg cab long box with a 302 V8 and dual tanks... I was driving around yesterday when my truck started to lung and then the motor stalled... when I stopped moving I tried starting the truck and it started with no problem, so as i kept on my way, about 5 minutes later the same thing happened and it stalled again, (I have an automatic by the way). but this time before it stopped moving i pump the gas a few times and it fired back up and then stalled again... i switched from my front take to by back maybe thinking it could me my fuel pump in the tank but it did the same thing again about same time later... Would it be my fuel filter on the frame (like in line fuel filter) or why is it doing that? its EFI by the way.
View 14 Replies
2002 E-250 with the 4.6 V-6. Pulled the 30 amp fuse, replaced the fuel filter, replaced the fuse, now the truck wont start. Checked the fuse and the kill switch under the passenger kick cover, all ok. Cranks and cranks but wont fire. No problem prior to changing the filter. Even swithed out the relay with another, no luck.
View 4 Replies
I have a 94 F250 5.8 liter with 96K miles. Can I remove the fuel rail and clean or replace the filter that is placed at the top of the fuel injector?
View 10 Replies
I have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 Replies
I have a 1999 Nissan Frontier, 4cy, 5speed. About a week ago, it began stumbling sporadically so my first thought was that maybe a spark plug had fouled. I changed the spark plugs, and the problem persisted. At this point, I begin thinking maybe it's a fuel issue. I went to Advance and bought Lucas Oil fuel system treatment and added it to the 1/2 tank of gas I had at the time. Going home from Advance it ran great. No stumbling. However, it started again the next day. I ran out that 1/2 tank of fuel and filled up again and it is still doing the same thing. It idles a little rough, and stumbles while going up through the RPM range between shifts. Once I get up to highway speed in 5th gear, it seems to do okay. Should I add more fuel injector cleaner or maybe SeaFoam? Could it possibly be a clogged fuel filter?
View 1 Replies
I have a very slow fuel drip off the housing for the fuel filter on the engine. Can't see where it's coming from. It started sometime after I changed the filter a couple of months ago.
View 5 Replies
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 Replies
I had my fuel filters changed at the dealership today on my '15, and then I bought fuel and headed home (70 miles). About half way home I got a "Low Fuel Pressure" message and a little while after that "Reduced Engine Power" along with the check engine light.
I pulled over to see if they did something like leave the drain open, thinking it might be sucking air. Of course it was dark and I could not see anything. However I did hear a buzzing sound and could feel a vibration when I touched the fuel line going into the top of engine filter.
While it is possible I got bad fuel, I suspect they did something wrong installing the filters. Even after cycling the fuel pump multiple times they had a hard time getting it started afterwards; I think they finally disconnected the top fuel line to bleed the air out.
I continued home and made it, but not sure what to do now; its 70 miles back to the dealer.
What is the most likely problem? Improper fuel filter installation or bad fuel?
Should I pull the filters in the morning see if there is something obvious like an out-of-place gasket? If so, top or bottom filter?
Is this a tow truck affair or should I drive 70 miles back to the dealer?
What the heck is the buzzing sound?
View 7 Replies
Have a 95 Bronco with 5.8, I turn the key on and fuel pump doesn`t shut off. Changed fuel pressure regulator still no shut off. Changed relays, no luck. Have 38 pounds pressure with key on, but no start. Checked spark just in case, and have fire. Don't know what to try next.
View 10 Replies
I have a holley 390 cfm carb on a 78 F250, 300 I6 with headers and an offy dp intake. Somewhere i am getting way too much fuel to the engine and it is sputtering and smoking bad. I have checked the float level, needle and seat, and power valve. All seemed ok but i replaced the power valve and needle and seat on the primary side just to be sure. Even with the float level adjusted way low and the idle mixture screws turned way in the truck would still sputter and spew out black smoke at idle and all throttle positions. I can't figure out where the gas is coming from. I checked to make sure the butterflies were closed and they were. I looked down the throat of the carb when it was running and didn't see any gas rushing in. When i take the carb off the bottom is soaked and the gasket and spacer is all soaked and theres gas sitting in the bottom of my intake. Where is this gas coming from?
View 14 Replies
I am unable to get fuel delivery from tanks to engine in normal operation. I can however get pumps working with jumper wire to them. It will start with ether but not stay running on it's own. Could this be a relay or something in tfi thing ?
View 14 Replies
Ok, I've replaced the fuel filter today and my truck still won't start. Checked fuses, and Fuel relay (19th slot). I've found the red fuel switch and it doesn't depress so I suspect it isn't tripped. I'm out of my league if I have a fuel pump problem.
View 6 Replies
After replacing fuel filter, pump relay, and air filter for good measure my 2002 f250 v10 gas engine still wont start. What to do?
View 13 Replies
Installing the diesel site fuel filter / water separator system for our 6.7's . And If so how do you like it. and your pro's and con's besides price.
View 4 Replies
I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
View 8 Replies
Changed fuel filters today. Now my water in fuel light is coming on. But the truck is not running any different no sputtering or anything. ????? Could this be human error
View 14 Replies
I just changed the drain valve on the fuel filter bowl. All went well and no more leak, but now I am getting an "emission system" warning light.
After I replaced the valve, I filled the fuel bowl with diesel fuel. Was there any other priming that needed to be done (if any)? What the emission system warning light may mean?
2002 F250 7.3L 4x4.
View 2 Replies
This van has had a couple of fuel pumps, no surprise there, and i need to look through my paperwork and find out how many miles the current one has on it, but it has the STRANGEST habit I've ever had on any vehicle. Starts fine, runs fine, no fuel pump noise when van is running, and when you turn it off, the fuel pump creeks on and off for several minutes.
I mean a strange creaking noise almost like a shorted electrical device or a vehicle's brakes when you park it on a hill and the breaks creak as it settles into place. I'm probably doing a lousy job of describing this but i don't know how else to describe it!
ALSO, if you lay under the van and wait til it stops creaking, you can tap the bottom of the tank and it will creak for a few more seconds. You can tap repeatedly and make it creak more. Is it about to explode? Can i trust it on a road trip?
View 6 Replies
I have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 Replies
