4150 Holley 532BBF float adj issue . I think i have it close, but its so hard to tell because the engine shakes the vehicle so much its hard to set the floats so that it just trickles out of the float holes. (532 kasse P51 heads, big roller cam) Is there an easier way to do it say on the bench?
View 1 RepliesI have a recently rebuilt 400 with a mild cam and Tmeyers flat top pistons. The carb is a 600cfm edlebrock that was bought new and installed a few months ago.
The issue I'm having is if I'm driving around and shut it off to run in the store its hard to start when I come back. I end up having to floor the gas to get it to start. When it's cold I tap the gas and turn the key and she lights right off. Could this be an issue with vapor lock? Why does it go away if I floor the gas?
Only other thing going on is when accelerating the engine runs noticeably smoother above 2700rpm. It's a little boggy below that. Probably two different problems but I figured I would throw it out there.
My truck will be running real good then all at once start missing so bad it shakes gear shifter,spits and pops and then goes back to running fine.
View 1 RepliesMy 302 runs pretty good when all warmed up. It has some cold start issues every now and then, but is easily dealt with. My question is how to best "tune" the carb. It's a 600 cfm 4150/60 style Holley single pump, vac secondaries and electric choke. About as basic as you can get. I think I have the fuel level set correctly. I also think I have the "idle mixture" set right. I used a vacuum gauge and moved back and forth between screws till I got the highest vacuum. Is there a better way than that? I have the idle set correctly. the fast idle is a little high, but I can fix that.
Now, my real question is how to fix the hiccup and stumble I get many times when I step into it pretty good. I assume that this is the point the carb is going from idle circuit to main circuit. It stumbles when I get on it real hard from a standing start. I can roll slowly and step into it and it stumbles as well. I also like to blip the throttle when I down shift (it has a manual tranny by the way), and many times I'll blip it and get nothing. Now, it runs fine after the stumble all through the rpm range. That's the only time it stumbles. so, do I need more accel. pump shot?? To compensate on the transfer of circuits.
I also notice when I on it real hard, during the shift right when I jump on it, under the heaviest load, I hear a bit of spark knock. It's not running hot, and the timing is good. Do I need a bit bigger jets? I'm thinking it's going a bit lead during that time, but I don't have any real way to measure it.
I have a holley 390 cfm carb on a 78 F250, 300 I6 with headers and an offy dp intake. Somewhere i am getting way too much fuel to the engine and it is sputtering and smoking bad. I have checked the float level, needle and seat, and power valve. All seemed ok but i replaced the power valve and needle and seat on the primary side just to be sure. Even with the float level adjusted way low and the idle mixture screws turned way in the truck would still sputter and spew out black smoke at idle and all throttle positions. I can't figure out where the gas is coming from. I checked to make sure the butterflies were closed and they were. I looked down the throat of the carb when it was running and didn't see any gas rushing in. When i take the carb off the bottom is soaked and the gasket and spacer is all soaked and theres gas sitting in the bottom of my intake. Where is this gas coming from?
View 14 RepliesIs it fair to assume that my filter is clogged when I turn over the engine and fuel does NOT come out of the filter with the uphill line disconnected. I was able to disconnect the rear line from filter and fuel DID pump out of line when I cranked it over. Been dealing with a crank no start, I'm in the process of trying to test my CPS properly but not sure if I'm testing it right.
2000 f 150 4.2 v6 232,000 miles....
I am unable to get fuel delivery from tanks to engine in normal operation. I can however get pumps working with jumper wire to them. It will start with ether but not stay running on it's own. Could this be a relay or something in tfi thing ?
View 14 RepliesI'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister, there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one. It's a 2007 Ford 4x4 6.0 diesel.
View 2 RepliesI have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
I have a 2001 Lincoln LS V8 that runs rich and no one can solve the problem that's been going on for close to a year. The fuel sys pressure tests fine. The fuel regulator sensor has been replaced. First start in morning is normal but after that I need to give it gas to get it to turn over. Also, car has a fuel smell.
View 8 Replies115,000 miles, adult driven. Hard cranking, took into dealer. Replaced 4 injectors - cylinder 2 misfiring. Showed me return gas line clogged with brownish material. Dealer stymied.
Now, Subaru headquarters diagnoses replacing all steel fuel lines, fuel rails, fuel pump...full of rust from inside. Tank looks Ok, as does filler neck. Premium gas used always, added Drygas seasonally as needed.
Question: where the heck would rust come from? What can I do to prevent this problem again? Love the car...would like to get 200,000 from it.
Over the last week my GX has developed a strange issue. It sometimes takes 3 or 4 tries of turning the key before the engine fires up. It turns over strongly and quickly but it isn't "catching". The weird thing is, it doesn't happen every time. Here is what I have noticed:
1) Leave the vehicle parked overnight - no issues starting. It starts right up.
2) Crank the vehicle after having only been off a few minutes (like after you run in to pick something up at the grocery store) it cranks right up.
3) Let the vehicle sit for between 1 and 4 or 5 hours and the problem appears. It turns over and over and over but won't actually start. Anywhere between the 3rd and 5th turn of the key it will finally catch and actually crank.
In all cases, once it cranks it runs smoothly and normally with no issues.
I have replaced the battery thinking that was the issue but that did not fix the problem. Also strange is the fact that this problem occurred after I replaced both front door speakers, an operation that required me to have one or more doors open for an hour or so at a time (hence why I thought it might be a weak battery).
I have a 2009 Pontiac Vibe with 43,000 miles. Recently the check engine light, the vehicle stability control light and the traction control system light all came on simultaneously. Since then they have all come on or all gone off several times. Usually once they come on, they stay on for the remainder of the trip. Sometimes they will still be on when I next start the car, sometimes they will be off. What might be causing this?
View 17 RepliesI have a 95 940 turbo that shakes really bad when braking. things I have done so far are.
1. Replaced all four rotors.
2. Replaced all four callipers.
3. Replaced sway bar control arms.
The shaking is so bad that the gear shift moves back and forth when braking.
We have an early model 460 with carburetor (circa 1976) in a boat. We need to exchange motors and have a line on a 1994 460 engine, fuel injected. Will the carburetor manifold we have fit in place of the fuel injected manifold and just run a carbureted manifold? Since this is for a boat there is no computer, no port for the exhaust sensor, and no sensor for the speed control. Its a plain and simple carburated motor.
View 1 Replies2001 Hyundai Sante Fe. When braking, I get a noise and the whole vehicle shakes. Exactly as if I were driving in snow and just slammed the brakes. The feeling & noise feels and sounds the exact same as if I were sliding...
I've replaced the master cyl originally just because today is the first day the issue lasted long enough for me to fully hear//feel the whole issue. It's normally brief.
I have an 84 Bronco II with a fuel injected 302 in it. I was out wheeling with it the other day, and it was doing great until about 3:00. I got out to see that my brothers radiator had sprung a leak. When I got back in my Bronco and put it in gear, it just stalled. I started it back up and it ran for about 10 seconds then shut off. It kept doing that over and over again. Finally, I got tired of it and had someone get my truck and tow me out of there. Why would it run for about 10-15 seconds only and then shut off like it was getting no fuel (yes, it does have fuel in it)? I have a feeling it might be fuel pressure regulator valve because it was acting up a while ago..
View 10 RepliesI got a new ipr an looking in the oil pump end there's a small spring with a screw n the middle. Is this a pressure adjustment for the valve or what any body no. I have a 97 power stroke that when i start it cold idles fine as engine warms it starts to miss . I have changed everything i mean everything but ipr and map sensor.
View 1 RepliesI have an 1980 Ford F-150 with an inline 300. I just installed a new egr valve on. Here is the problem:
After the engine warms up with everything connected, the engine starts to cut out and die while idling. This is due to the VCV opening up and allowing vacuum to the EGR. My question is why is this happening? The EGR is not suppose to open up during idle.
Have a 1977 ford f150 with 351m with a motorcraft 2150. Had ( who I believe was a reliable source ) rebuild carburetor for me and after putting back on I can only keep engine running with foot on pedal. I turn idle mixture screws all way in and then proceeded to back out equally. This does not appear to be doing anything. I did turn the choke 2 notches to lean and was able to get it to idle but it wasloping so bad i shut it down and put the choke back to the middle setting.
View 13 RepliesWhat to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.
Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.
Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.
The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.
Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.
What would my next step be? Where should i look next?
1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.