Ford Fuel System :: Can Broken Dipstick Tube Cause Lean Codes?
Jul 8, 2011
It's really not relevant what brought up this question but do you think a broken dipstick tube can cause an engine to run lean and why do you answer that way?
View 3 Replies
Jul 8, 2011
Advertisement
Passat (B5) :: Oil Dipstick Tube Broken In Half
I was checking the oil this morning before getting ready to drive (for an hour) to the in-laws for Christmas, and the Effing orange plastic dipstick tube broke about halfway down. Now I'm afraid to drive for an hour at highway speeds, for fear that a lot of oil might come out of that compromised Effing orange plastic dipstick tube part -- would you all agree that I should not drive the car? Figures this would happen on Christmas Eve when nothing is open.
Effing orange plastic dipstick tube!
Ford Super Duty (1999-2016) :: Broken Dipstick Tube At Block On 5.4 Plow Truck
I just finished putting a 7.3 back in one of our f450 plow trucks today, so then i moved onto our 2001 F250 5.4 plow truck. The dipstick tube was rusted in half so i pulled on the remaining half to get it out and put in the new dipstick. However, it broke off at the block. So now i cannot see how to get the rest out with out doing a lot more work. I haven't removed the splash guard yet but will i have to remove the manifold , the oil filter base, or both?
View 14 RepliesSanta Fe (CM - 2007-12) :: Check Engine Light Going On - Fuel System Lean Codes P0171 And P2187
My wifes 2007 Santa Fe Limited 3.3 has had a check engine light going on a year now. Car has about 122k on it now. Scanned codes about 6 months ago and had a fuel system lean code. Did some reading and ended up replacing the purge valve. The CEL stayed off til the end of the drive cycle and came right back. I have noticed when you fill the car up there is a real strong smell of gas but the car always starts right up. It now has a P0171 Fuel system too lean (b1) and P2187 Fuel system too lean at idle. Where to start. Don't have much background with hyundai. Also the ESC off light comes on randomly and goes off. Doesn't happen real frequently though.
View 4 RepliesFord Fuel System :: 4180c - Fuel Coming Out Of Primary Vent Tube
I have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 RepliesPhaeton :: MIL Light On / System Too Lean Codes
I just got this car a 04 4.2l, put about 2000km on it and MIL light now on. Just got VCDS here is the scan.
I tried clearing the system too lean codes and shut off MIL and engine ran poorly, I think that is the cyl misfire codes.
Car runs fine with MIL on, averaging 10.8 l/100km hwy driving, but need to get emission tested and here in Ontario, they read the obd.
VCDS Version: Release 12.12.0 (x64)
Data version: 20130910
Monday,23,September,2013,19:21:03:35803
Chassis Type: 3D (3D - VW Phaeton (2002 > 2006))
Scan: 01 02 03 05 06 07 08 09 11 13 15 16 17 18 19 23 27 28 29 2E
34 36 37 38 39 46 47 55 56 57 65 66 68 69 71 75 76 77
[Code] ....
Ford Fuel System :: Gas Tank Pickup Tube Replaceable?
Do the dip tube/fuel pickup tube inside the fuel tank is replaceable? The tank I have is a behind the seat tank.
View 1 RepliesFord Fuel System :: 1988 - Got Code 41 - Lean Miss At Idle - ECM Or Injectors?
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
Passat (B5) :: 2001 - Emission Workshop / Misfire On 4 Cylinders And System Too Lean Codes
I am getting the dreaded emission workshop.
The codes i am getting are p0301-p0304 and p0171
Which are misfire on 4 cylinders and system to lean (bank 1).
Here is what I have done:
Got the 4 ignition coils replace, replaced the mass air flow, replaced the air filter, replace the plugs.
I just check the L wire and it doesn't have any cracks or holes
I don't know what to do next.
Ford F-150 (2004-2008) :: Rough Idle And Dying / System Adaptive Fuel Too Lean Bank 1
2004 f150 fx4 w/ 5.4 .I have a code that read " system adaptive fuel to lean bank 1 " and the same for bank two. So, I got on here and did some research. Cleaned the throttle body, maf sensor, air filter, looked for vacuum leaks, changed the fuel filter and it still is running very poor at idle and it seems to be getting progressively worse...
View 2 RepliesFord - Contour :: Smoke Coming Out Of Oil Dipstick Tube
I've got smoke coming out of my oil dipstick tube. 1996 Mercury Mystique 2.0L automatic, 62000 miles. I noticed a burning oil smell after a short (10 mile) drive, and checked the oil when I got home. A few wisps of smoke smelling of burning oil came out of the dipstick tube when I removed the stick. I was just curious how worried I should be about this.
As far as I can tell, my cooling system works (radiator hoses are warm, good hot air from the vents, thermostat and coolant recently replaced, hoses inspected, no leaks) and I'm not thinking the burnt oil is caused by overheating. There hasn't been any noticeable oil consumption, and I'm pretty diligent about checking the oil on this old car. Oil changes every 3000 miles since I've owned the car; dealer performed scheduled maintenance for the old owners.
Here's my thinking: a worn piston ring allowing oil to be burnt and then sucked back through into the crankcase. When I changed my spark plugs, I did notice an oily residue on one of the plugs (cylinder #1), which also leads me towards a piston ring diagnosis (though I was hoping it was a valve seal causing the oily spark plug, or even a spark plug seal). Do a wet compression test is in order, or should I go ahead and get a leakdown test? I am going to buy a compression tester, but I do not have an air compressor to use with the leakdown tester; I'd have to take it to a shop.
I do need to service the PCV system (and would have done it today, but the parts hadn't arrived at the store) -- would a PCV problem cause the oil to burn, though?
Ford F-150 - 1997-2003 :: Dipstick Tube Fell In Oil Pan?
Rusted dipstick tube I thought was going to be an easy enough fix. Broke off clean at the block. Tried for hours, easy out, prying, vise grips anything I could think of. Well I tried to pry the side of the tube over to make room for my needle nose vise grips, and boom. Down in the oil pan it goes.
Do you think theres any way possible I can fish it out through the drain plug. I really dont want to pull the darn motor.
Ford Fuel System :: 2003 F150 - Service Light Randomly Comes On / Code For Left Bank Running Lean
2003 f150 supercrew with 166,000 miles on it. Daily driver. Service light randomly comes on and when code reader was put to it shows "left bank running lean." Will clear it and will randomly come back on. Truck seems to be running fine. No issues engine. Bad sensor? Or bad injector? Maybe way to test?
View 1 RepliesFord F-150 (2009-2014) :: Transmission Dipstick Tube Leaking
I was changing my oil the other week and when i went to pull the filter I noticed that my tranny pan was wet around the front side, as well as the flywheel insp. plate, and the tranny dipstick tube. It wasn't even enough to drip on my driveway, but wet none the less. after cleaning it up really well and driving it around for 15 minutes it seemed to be coming from the dipstick tube about halfway between where it seats in the tranny and top end of the dipstick.
Removing the tube was easy, just one 10 mm bolt on the back of the engine. After further insp, there was a small piece of insulation on the tube where it passes between the engine and exhaust manifold. when i removed that insulation i noticed there was rust on both the top and bottom of where the insulation sits. i looked it over really well and didnt' see any cracks or holes. I then pluged one end and blew into the other and didnt' notice a loss of pressure or any hissing noise.
I figured if it wasn't leaking and it was already out i might as well clean off the rust and hit it with some paint. I ran a wire brush over the lowest spot of rust and what do you know, 3 tiny little pin holes. I used some 2 part apoxy from work and some aluminum duct tape to repair the hole temporarily until i got the new part in the mail yesterday. total install took around 10 minutes.
Santa Fe (CM - 2007-12) :: 2008 - CEL On / Fuel Trim System Lean At Idle
I just got this 2008 santa fe a month ago from the dealer with 80.000 miles , and then yesterday the check engine light came on, i took it to auto zone and the put the computer and this 2 codes came up:
P2187
Fuel trim system lean at idle
explanation
the average long term fuel trim values at idle are more than 30% for 10 seconds
probable cause
- low fuel presure
- failed MAF sensor
- large vacuum leak
- cylinder misfire due to ignition system failure
P2189
System too lean at idle bank 2
explanation
failed MAF
probable cause
- low fuel presure
- vacuum leak on engine
- failed HO2S ( heated oxygen sensor-bank2 )
Ford F-150 - 1997-2003 :: Engine Is Leaking Oil - Dipstick And Tube Come Off When Pulled
I got a 97 F250 4x4 w/ 4.6 lt. motor & auto trans. The engine is leaking oil. It looks to be coming from a set of hoses that are on the adaptor that is between the oil filter & the engine block. Also what are the oil lines called? It is leaking motor oil not transmission oil.
Also just pulled my oil dip stick & the whole thing (dip stick & the tube) came off the truck. Seems the tube has rotted away at the oil pan. Is this also a job I can do?
Ford F-150 - 1997-2003 :: Trans Dipstick Tube Leak - No ORing?
I have a minor leak at the base of the trans dipstick tube. I assume that the tube is press in ? has an o-ring ? I put some silicone around the area and that worked about a week, the fluid is probably eating through that type sealant. The trans is a 4r70. Seems to me that the actual tube should be ok and having never dealt with replacing one I want a little advice before yanking it out.
View 11 RepliesFord Super Duty (1999-2016) :: Dipstick Tube Replacement?
The dipstick tube on my 5.4 snap and ive ordered a new one. it looks like it may not be to hard to replace.
View 4 RepliesFord Transmission :: 2006 F250 - Dipstick Blowing Out Of Tube Due To Back Pressure
Have a 2006 F-250 with 5.4 motor pulling a 25 ft house trailer. No issues until the towing began a couple weeks ago. Back pressure is building up in the transmission and it is blowing the dipstick out of the transmission tube and spraying fluid all over the place. Truck has 132k miles on it and last serviced @125k miles. No slippage. Fluid isn't burnt. Separate transmission heat gauge not registering hot and it is working - fuse not blown. The transmission does have an auxillary filter on it which is going to get changed tomorrow to see if that solves the problem. Transmission is Automatic. Not driving in 4th gear because of towing. Any thoughts what might be blocking to cause this pressure buildup?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Dipstick Tube Flange Leaking
The dipstick tube flange is now leaking ....
View 3 RepliesPassat (B5) :: Check Engine Light Came On - Code P0171 / Fuel System For Bank 1 Was Too Lean
We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:
1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem
Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.
I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.