Ford Fuel System :: Bogs On Acceleration
Mar 29, 2008
I have a 460 with a holley manual choke 750 single pumper carb on it, when I pull out truck bogs very badly, if I try to punch it will stall unless I let off the throttle.
It seems to run best with choke almost all the way on. What the problem could be?
I'm almost positive its a carburetor problem, just not sure exactly what the problem is, could a blown power valve cause this??
The accelerator pump seems to be working properly ...
View 3 Replies
Advertisement
i recently got a 86 f250 351w ho. My problem is when i go from a stop or even slow for a turn then reaccelerate it bogs down and i have to pump the pedal to keep is going. My first thought was the accelerator pump but now I'm thinking power valve? I believe this carb is a Holley 4180?
View 3 Replies
My 1993 ford aerostar 3.0 is a great vehicle but recently its been killing me trying to figure out what the cause is. I'll start at the beginning. I had a job over the hill in Westwood Ca. Ran low on gas on the way home. Too low apparently. Since i refueled it has a really rough idle and no power under acceleration. After it gets warmed up i get a bad smell of gas and exhaust in the cab.
Now if i turn it off wait 15 min or 12 hours it will run ok for 2 min then back to hell. I has not stalled and i have replaced the fuel filter and a few months back i cleaned the Mass air flow sensor and replaced the TPS. I would love to take it to a mechanic but as i have been living in this old girl for the passed 6 months money is non-existent.
What to do. I have even tried disconnecting 1 at a time... the TPS, MAF, and the 02 sensor. No difference. There has been no check engine light until I tested by disconnecting TPS etc.
View 8 Replies
2001 F-350 7.3L / 147K... Lately my truck has a strange anomaly when I take off from a stop. A few seconds into a routine gradual acceleration the engine gets a little "boost" without changing anything on the accelerator. I typically take off from a stop as if an egg is under my foot. And then bam! It's as if I romp down on the gas pedal. Not a lot of increase in rpm's and acceleration, just a hint. BUT NOTICEABLE! Even my wife wondered why I was playing with the accelerator. And, it only does it that first time you start it and take off. I had the glow plugs replaced last week. And it has done it occasionally before but increasingly since. No other changes other than pulling codes.
View 1 Replies
My 07 F150 has no power. I changed the timing chain, cam phasers, spark plugs and all 8 coils and still no power. Rough idle and bogs on acceleration.
View 3 Replies
I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
View 8 Replies
I have a 97 Pontiac Grand Am w 3.1 engine that is my son's college car. We recently rebuilt the original engine and put it in after having a 99 monte carlo 3.1 engine in it's place and it had a head gasket problem as well. Just before we switched engines my son was noticing that it would kind of hesitate under acceleration from about 1500 rpm to around 2000 rpm especially when it was wanting to up shift. I figured it would resolve itself with the engine change. It did not. It has now gradually gotten worse.
My son drove it to Liberal about 4 hours away and he stated it was worse and especially when you would get into overdrive it would drop down to around 2000 rpm then start sputtering or loading up or just being dead then would down shift to 3rd and try to clean itself out and speed up and then up shift to OD and do the same cycle again. I drove it back and kept it in 3rd gear and seemed to run fine at 2500 or higher. I also had to go thru low, and 2 and feather it up from a standing start. It idles fine as well.
I thought it might be like one of the saturns I had which ended up having a plugged Catalytic converter and a bad coolant temp sensor. This morning I did a test hole and it made no difference. I tried a different coil pack/ESC and it made no difference. I cleaned the MAF sensor and no change. The fuel pressure is 41 then 38 when idling then 43 when remove the fuel pressure regulator vacuum hose. I also changed the fuel filter.
I was kind of ruling out the tps, iac, and egr and water temp sensor as those were part of the other engine when I put the other engine in so they are different and I am assuming they must be good. Plugs and plug wires are new as well. It has not thrown any codes. I did notice that when it is just in park and you press on the accelerator to rev it up it only will rev to 3500 rpm and will shut down like a rev limiter is kicking in and just do a kind of surge thing. My saturn did that too and it was a plugged cat and when I knocked the biskit out of the manifold on that car it stopped. I have already got that ruled out though.
View 3 Replies
I seem to have fixed all the other problems i was having except 1. I blew the head gaskets on my Z and it sat in the garage for about 2 months. Tore it apart and changed everything, now I have an issue when it runs for about a minute or so when i get on it, it bogs down and has terrible acceleration. I just changed the opti, coil, icm, oil pressure sender, new plugs. Engine light was on previously gave codes, 48 and 29. swapped out my MAS sensor... checked fuses and there was a bad one for the air pump, changed it and the ses light went off.... I am thinking a fuel filter needs replaced? I am at a loss here. It ran perfectly fine before i blew the gaskets. its a little rough at idle, but i had cut my cat off and ran 3" out the back to the flowmaster....
View 7 Replies
My friend has 2000 12v vr6 auto and recently he experienced his car bogging under acceleration. He had the plugs and wires recently done to solve the problem and the problem went away for a day and has since returned. I scanned it and here are the codes that its threw. After doing some research i'm thinking its the coil pack, since it was pretty foggy/damp today (when the problem started again).
17626.p1218 - fuel injector for cylinder 6 (N84): short to b+
16690.p0306 - Cylinder 6 Misfire Detected
16684.p0300 - Random/Multiple Cylinder Misfire Detected
View 1 Replies
I went to move the 2000 yesterday and it will not start because the gas went bad. It has been sitting about 6 months, since it did not snow this past winter. How do I go about cleaning the fuel system? I was thinking suck the gas tank empty with an electric fuel pump, and blowing out the lines with air. Does this sound right?
View 7 Replies
This van has had a couple of fuel pumps, no surprise there, and i need to look through my paperwork and find out how many miles the current one has on it, but it has the STRANGEST habit I've ever had on any vehicle. Starts fine, runs fine, no fuel pump noise when van is running, and when you turn it off, the fuel pump creeks on and off for several minutes.
I mean a strange creaking noise almost like a shorted electrical device or a vehicle's brakes when you park it on a hill and the breaks creak as it settles into place. I'm probably doing a lousy job of describing this but i don't know how else to describe it!
ALSO, if you lay under the van and wait til it stops creaking, you can tap the bottom of the tank and it will creak for a few more seconds. You can tap repeatedly and make it creak more. Is it about to explode? Can i trust it on a road trip?
View 6 Replies
I have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 Replies
What would make a FI engine act like its flooding out and dying after a short run on the freeway?
Details:
1994 F-350 351W (just overhauled this winter)
has new TPS, ICM(?).
Dual exhaust dumps right before the tires
new filters in tanks, new fuel filter on frame rail
All fuel lines have been opened and blown out from the tank to the engine compartment fitting near firewall.
Fuel pumps hold good pressure when tested.
Symptoms:
smells like its running rich most all the time
after a short hiway run @ 70MPH it will stumble and die when returning to surface streets.
fuel smell near engine sometimes, but no obvious puddles or leaks anywhere.
May be related?:
When on a longer highway run, I can't use the FWD tank for a long period without the engine stumbling and cutting out or popping at times. But I can swap to the rear tank for a bit then run the FWD tank again for a while. driving up hills it seems to be worse, but I'm in the panhandle of TX right now..good grief!
I am having to drive this truck for work long distances. While I dont expect a vast fuel range, it would be nice if I could go a couple hundred miles on 20 gallons of gas....
View 9 Replies
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
View 2 Replies
I have a 95 F150 4x4 reg cab long box with a 302 V8 and dual tanks... I was driving around yesterday when my truck started to lung and then the motor stalled... when I stopped moving I tried starting the truck and it started with no problem, so as i kept on my way, about 5 minutes later the same thing happened and it stalled again, (I have an automatic by the way). but this time before it stopped moving i pump the gas a few times and it fired back up and then stalled again... i switched from my front take to by back maybe thinking it could me my fuel pump in the tank but it did the same thing again about same time later... Would it be my fuel filter on the frame (like in line fuel filter) or why is it doing that? its EFI by the way.
View 14 Replies
My vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
View 3 Replies
2002 E-250 with the 4.6 V-6. Pulled the 30 amp fuse, replaced the fuel filter, replaced the fuse, now the truck wont start. Checked the fuse and the kill switch under the passenger kick cover, all ok. Cranks and cranks but wont fire. No problem prior to changing the filter. Even swithed out the relay with another, no luck.
View 4 Replies
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 Replies
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
View 4 Replies
My '90 E250, open road, mini motorhome , says on the radiator mount , that there is a Fuel shutoff switch that may have been activated.... I don't have the manual for it, so I need finding the switch, so I can reset it ....The vehicle sometimes starts after about 2 mins with the ignition on, but today won't start, even after a longer wait. Both tanks are full...Fuel gauge not working , in either front or rear position. I can hear the rear pump,in the tank, but can not hear the front one....When I bought it last year, it ran fine after waiting to start, and both positions worked , no stalling , or shutdown.Came home about 95 miles, and it's been parked almost all the time since. I want to start it up weekly , but am having that same problem ...Today was the first time I could see the Fuel Pump Shutoff warning ...but can 't find the darn switch to try resetting .....
View 1 Replies
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 Replies
