Ford Fuel System :: 1994 F250 - Start Missing And Shakes Gear Shift?
Nov 5, 2012
My truck will be running real good then all at once start missing so bad it shakes gear shifter,spits and pops and then goes back to running fine.
View 1 Replies
Nov 5, 2012
Advertisement
Ford Fuel System :: 1994 F250 - Fuel Injector / Clean Or Replace Filter
I have a 94 F250 5.8 liter with 96K miles. Can I remove the fuel rail and clean or replace the filter that is placed at the top of the fuel injector?
View 10 RepliesFord Fuel System :: 1994 F150 Won't Start - No Fuel Comes Out Of The Valve
1994 150 300 6. parked truck after lunch finished work and it wont start no fuel comes out of the valve. Can't get the pump to work even when jumping the 6 pin. heard the relay click still nothing. Checked the inertia switch it wasn't popped. Took the pump out jumped it straight from the battery pump works . I know there has to be something i am missing...
View 7 RepliesFord Fuel System :: 1994 F250 - Front Gas Tank Not Working
Ok heres the story 1994 ford f250 7.5 4x4 dual tanks I used both front and rear tanks regualrly than one day front tank stoped working fuel pump doesnt turn on when key is in the on postion now you can hear the rear turn on when switched to rear tank took off pigtail connector to front tank no power at all to tank took off swith in dash no power there either good relay and fuse funny thing is with swith turned to front fuel guage reads correctly switch to rear reads correctly Im stumped because oveiously Im getting power to the switch but checked wires at switch and cant get any power or at front tank but power to rear.
View 6 RepliesFord Fuel System :: 1994 F150 - No Start After Running When Turned Off
I have a 1994 f 150 5.8l 4x4 with 215000. Cold starting is fine runs well. After running it will not start after shut down. Wait till motor cools back down will start up and run fine ....
View 2 RepliesFord Fuel System :: 1994 F150 Fails To Start When Turn The Key In Ignition
I have a 1994 F150 XLT 5.0 . The problem i am having is when I turn the ignition on I hear the fuel pump come on [both front and rear tanks] and it should stop when the system is pressurized but it does not,and the truck then fails to start. Intermittantly the pump does stop and the truck starts up.
There is fuel at the rail and there is spark,i have changed the filter ,fuel pressure regulater and the pump relay to no avail.
Ford Fuel System :: 1994 - Intake Fuel Pump Quits When Gets Hot
I have a 1994 Ford 460 motorhome with a intank fuel pump that quits when it gets hot. so I was thing of butting a heavy duty in line pump on and just pull it through the old pump can this be done safely. Or is it best to drop the tank and just put a new fuel pump in.
View 10 RepliesFord Fuel System :: 1994 F150 - Replacing Fuel Lines?
I'm looking at replacing the fuel lines in my 94 F150 and the big question is what to do with hooking up to the fuel lines coming out of the fuel pump hat and the fuel rails? Ford uses a specialized pressure fitting on it's custom fuel lines. I think there may be some third party fittings that would replace these, but I'm not sure. I could use a standard hose and cable clamps, but I just don't trust that kind of connection for a fuel line.
View 5 RepliesFord Fuel System :: 1971 F250 - Gas Leaking - A Lot Of Crank To Start - Rebuild?
I have a 1971 F250 automatic with original stock 360 engine (100k miles). It currently has an Autolite 2100 2bbl carb.
The Autolite is leaking gas out somewhere where I can't see the leak. It takes a lot of cranking for it to start after sitting 10 minutes and my wife won't drive it for fear of being stranded. My attempt at a rebuild must have failed... Also have issues with anti-stall dashpot spring coming off while driving. When the spring and plunger come off I have to hold the gas on a little to keep from stalling while stopped at a light. A couple other parts looked like they needed repair during the rebuilt, but the kit didn't have any replacement (vacuum diaphragm torn). Also, after replacing plugs, plug wires, replacing points with Pertronix Ignitor 2, a new rotor, and distributor cap, it still doesn't hold a steady idle. In fact it is hard to get it down to the spec idle for an automatic without fear of stalling.
To make a long story short, what is a low maintenance 2bbl (new, not rebuilt) replacement carb. The truck needs to be dependably started by my wife for garage sale runs and home depot trips. I could switch to a 4 bbl intake, but would rather wait for another 50k miles and switch the engine over to a rebuild 390 with nicer intake and carb.
Ford Fuel System :: Engine Shakes The Vehicle So Much / Hard To Set The Floats
4150 Holley 532BBF float adj issue . I think i have it close, but its so hard to tell because the engine shakes the vehicle so much its hard to set the floats so that it just trickles out of the float holes. (532 kasse P51 heads, big roller cam) Is there an easier way to do it say on the bench?
View 1 RepliesFord Fuel System :: 1997 - Missing When Engine Warms Up
I got a new ipr an looking in the oil pump end there's a small spring with a screw n the middle. Is this a pressure adjustment for the valve or what any body no. I have a 97 power stroke that when i start it cold idles fine as engine warms it starts to miss . I have changed everything i mean everything but ipr and map sensor.
View 1 RepliesFord Fuel System :: 1994 - 4 Injectors Do Not Pulse
I have a f53 motorhome and 4 out of the 8 injectors pulse. The front 2 and the back 2 don't pulse. The middle 2 on both sides work perfect. Why would they not pulse and only give out positive on the two wires to the injector on the one that don't work. The ones that work they pulse.
View 8 RepliesFord Fuel System :: 2001 Excursion Started Missing / Loss Of Power
2001 Excursion 7.3 started missing the other night. Great loss of power, but made it home. Rough idle, "clacky". Next morning, did the following in order: 1) Pulled the fuel filter inspected, 2) removed all fuel from the bowl 3) replaced bowl fuel with Seafoam 4) installed new filter (my typical procedure). Without starting, I then 5) removed HPOP oil from reservoir and 6) filled with fresh oil using exact amount removed as a gauge for what to replace.
Started, idle smooth for a time. Increased rpm by depressing accelerator. Began running rougher and rougher accompanied by white smoke. Finally quit and would not restart. Cranking easily, tachometer showing RPM during crank. Suspected no fuel getting to fuel bowl. 7) Drained fuel bowl using valve on back of bowl. 8) Turned ignition to "on" to get fuel pump to run 9) removed new filter, no fuel in bowl 10) With fuel filter out of the bowl, removed fuel filter and quickly cycled the ignition to "on" and back off -- no fuel entered the bowl. 11) Removed leads from fuel pump. 12) Checked voltage across leads as ignition cycled to "on": 6.5 volts. 13) Checked fuel pump fuse (20A Maxi fuse in location 112 -- BLOWN!) 14) Replaced fuse, performed voltage test: 11.55 volts 15) Checked battery voltage: 12.44Volts.
So, with all that, how in the world does the fuel pump get 6.5 volts with the fuse blown? I looked closely at the fuse and there was no slag or connection in the element. Today I have pulled the 9-pin and 42-pin connections on the valve covers as well as the connectors to the glow plug relay module (used on Ex's) to inspect wires and connections. All looked fine. I plan to us some LP5 electro contact cleaner to clean all the connections and put some electrical grease on the connections, but the big question is where did that 6.5V come from with the fuse blown. I plan to pull the fuse and do the same test to see if the 6.5V is still there.
Ford 7.3L Power Stroke (1999-2003) :: 1994 F250 Missing Under Load / Loses Power
1994 f250 7.3 turbo problem.. runs great on the level.. Cruises 65 no problem.. We have an 8% grade coming from town and half way up it starts cutting out and sounds like a jack brake under the hood and loses power.. Once over the top it clears out and runs fine again.... I just changed the fuel filters but no luck... I have been wrenching on cars all my life but no diesels..
View 6 RepliesFord Transmission :: Truck Moves Forward In Every Gear Including Park - Missing Shift Detent
Reverse band broke in my C4, I took it apart enough to get the rear band out and then reassembled. Everything to my knowledge was seated correctly and the front pump seated flush with the case when I reinstalled (which is supposedly a sign that it is all seated correctly). I adjusted the bands to spec and replaced the vacuum modulator and torque converter. These were the only things replaced besides the reverse/low band. Vac modulator was replaced to original (yellow band) as I was running an adjustable before. TC was replaced just because I did not the last time I had the trans rebuilt in 2003....decided to go ahead and R&R.
I got everything assembled, filled up with fluid and no leaks. I start it up and once i finished topping it off, the truck moves forward in every gear... including park! It also seems that I'm missing a shift detent. I have P, R, N, D, 2 but no 1. I disconnected the shift linkage and tried manually shifting from the trans and have the same issue.
I did not open up the valve body, just unbolted and replaced. When you start it up, it doesn't jump forward (while in park) but when you rev it up it sounds like the motor is under load. I've consulted my Haynes C4 book and an extensive google search and no way...
Ford Fuel System :: 1991 F250 XLT - Fuel Pump Will Not Stop Running
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
Ford Fuel System :: F250 Not Getting Voltage To Fuel Pump Relay
My F250 heavy duty isnt getting voltage to the fuel pump relay.....
View 2 RepliesFord Fuel System :: 1994 F150 - Gas Tank Leaks - Removal And Installation
I just got a 1994 F150 with the 5.8L motor its a 4X4 with Auto trans. I have the dual tanks set up, midship and aft-axle and both tanks leak, more aft-axle then front. I was wondering how difficult is it to remove and install these tanks and what are some tricks to solve the problems I'll run into?
View 4 RepliesFord Fuel System :: 1988 F250 Stalls - Random Fuel Pressure Loss?
I have a 1988 Ford F-250 Lariat, 7.5L 460, four-wheel drive. I have two fuel tanks on it, and I've been having a really annoying, obnoxious problem with it lately. After running it for a while, I noticed that I keep losing fuel pressure, and the truck stalls. When I try to start it, it does nothing but roll over. It just won't start. I've changed the fuel filter, I know both fuel pumps are working (I turn over the key, I can hear front, back, and high pressure pump attached to the left side frame rail kick in.) It's Fuel Injected, not EFI, hence that third pump. The problem happens a lot, and it's random. I could drive for 100 miles, stop to get something to eat, come out, and it won't start.
I thought maybe it was the fuel pressure regulator, but I don't think that's the case because it still runs. I would assume that if the regulator was bad, it wouldn't run at all. I also thought that maybe it was the relay, but according to some mechanics I spoke too, if I can hear the pumps kick in when I turn the key over, then the relay is fine. The only thing I could think of is that it might be the fuel selector switch. Maybe it's going bad, shorting out or something. When I flip the switch though, it switches between fuel tanks, and the gauge reads how much fuel is in it from the sending unit.
There's a schrader-type valve up by the fuel injectors. When I push it in, it barely squirts any fuel out, if at all, so I know the pressure is low. When I push it in on a good day, it sprays out like a water fountain. Just tried starting it again - no good. Pushed on the valve, it spurted out some fuel pretty well, but still won't start. Occasionally tries to, but ultimately won't. I know the spark is good, checked the plugs/distributor cap. Can't get the sucker to start.
Ford Fuel System :: 1977 F250 - Fuel Leak From Filter Attached To Carburetor
I have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 RepliesFord Fuel System :: 1989 F250 Fuel Pressure Drop Quickly Under Heavy Load
I am a newbie as far as fuel injection. The original issue the truck had was no fuel. I tracked down the issues to a blown fuel pump relay and a melted inertia switch. I jumped the inertia wires with a new fuel pump relay installed and the truck ran at an idle and up to 3500 RPM when stationary. If the truck is going up a grade or needs more throttle it will start to lose fuel pressure and end up stalling. I had the fuel pressure gauge connected to the schrader valve on the fuel rail and had 30-35 PSI when idling. It runs good under light load on the throttle.
Under heavy load it starts to drop quickly and if you back off the throttle it will stay running some times. I changed the fuel filter and also replaced the high pressure pump on the main frame and it still has the same problems.The original pump was pumping about 13 ounces of fuel in the 20 second test that the repair manual suggested. I have even placed a jumper wire direct to the new fuel pump to bypass original wiring and possible problems. When it stalls under load (No Fuel pressure) at the schrader valve you can hear the fuel pump running but there is no fuel pressure.
If I turn off the ignition for a few minutes and then turn the key back to the on position it will start to pressurize and then start and run at an idle. I even replace the ignition switch as it was a little temperamental. I have not changed or checked the fuel pressure regulator as it is a pain to get to at the back of the engine. I do not want to spend a fortune tracking down this problem since the truck may not even pass its smog inspection and may be a parts truck only.
67 F-250 4x4
73 Crew 4x2 (4x4 Soon)
89 F-250 Super Cab 4x4