Ford Fuel System :: 1994 F150 - Replacing Fuel Lines?
Jul 7, 2008
I'm looking at replacing the fuel lines in my 94 F150 and the big question is what to do with hooking up to the fuel lines coming out of the fuel pump hat and the fuel rails? Ford uses a specialized pressure fitting on it's custom fuel lines. I think there may be some third party fittings that would replace these, but I'm not sure. I could use a standard hose and cable clamps, but I just don't trust that kind of connection for a fuel line.
View 5 Replies
Advertisement
1994 150 300 6. parked truck after lunch finished work and it wont start no fuel comes out of the valve. Can't get the pump to work even when jumping the 6 pin. heard the relay click still nothing. Checked the inertia switch it wasn't popped. Took the pump out jumped it straight from the battery pump works . I know there has to be something i am missing...
View 7 Replies
I have a 1994 f 150 5.8l 4x4 with 215000. Cold starting is fine runs well. After running it will not start after shut down. Wait till motor cools back down will start up and run fine ....
View 2 Replies
I have a 1994 F150 XLT 5.0 . The problem i am having is when I turn the ignition on I hear the fuel pump come on [both front and rear tanks] and it should stop when the system is pressurized but it does not,and the truck then fails to start. Intermittantly the pump does stop and the truck starts up.
There is fuel at the rail and there is spark,i have changed the filter ,fuel pressure regulater and the pump relay to no avail.
View 4 Replies
I just got a 1994 F150 with the 5.8L motor its a 4X4 with Auto trans. I have the dual tanks set up, midship and aft-axle and both tanks leak, more aft-axle then front. I was wondering how difficult is it to remove and install these tanks and what are some tricks to solve the problems I'll run into?
View 4 Replies
I am done with this swap (I hope) changed out the 302 in my 81 van for a 351. The only smog spaghetti I am keeping is the fuel vapor canister but I am unsure what the #1 line in the photo is for I have the manual but doesn't state what it does my research suggests its a fuel vapor return line from the carb bowl back to the canister ...... I now have an edlebrock carb obviously w/o this port so my question is
#1 where would you reconnect this "whatever it is" line on carb or manifold
#2 I am going to install that #3 fitting in photo on the edlebrock manifold at the same location & extend #2 hose to it. I am thinking that's ok...
View 1 Replies
My vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
View 3 Replies
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 Replies
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
View 4 Replies
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 Replies
cant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 Replies
Why the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 Replies
for the past week we have been trying to figure out what is wrong with our truck. We recently bought it and it ran fine. Then got in a minor accident just a fender bender and it started acting up so I got towed to garage. First it would run when cold, but when hot fuel pressure would drop to 28 psi.
So I put new fuel pump, it started but still did the same thing hot 28 psi fuel pressure shuts off. So I put regulator on it, then had 0 fuel pressure won't even start. So got a another regulator thinking I got a bad one, still 0. Checked relay, there fine. I'm gonna check lines and see where fuel stops at but everything is new on it.
View 1 Replies
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 Replies
I have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...
View 2 Replies
I have a 1994 Ford 460 motorhome with a intank fuel pump that quits when it gets hot. so I was thing of butting a heavy duty in line pump on and just pull it through the old pump can this be done safely. Or is it best to drop the tank and just put a new fuel pump in.
View 10 Replies
I have a 94 F250 5.8 liter with 96K miles. Can I remove the fuel rail and clean or replace the filter that is placed at the top of the fuel injector?
View 10 Replies
Yesterday , my feed fuel line was dry rotting and leaking gas so I bought 516 fuel injection hose and replaced them. Pulled fuse 28 , started the car and let it die to release pressure , fixed the hoses and put the fuse back in and now it just cranks forever. I have spark , and I'm getting fuel just not sure if it's adequate pressure. When I open the door the pump did sound a little funny when it primed. I'm gonna pull it out and check it later but right now I'm completely stumped. I did this last night around 8pm and it's 4:30 am the next morning and still not start.
View 6 Replies
1991 F150XLT, 5.0, E4OD....Should the EFI system bump up the idle speed when the AC system is operating to compensate for the compressor load? Obviously I'm asking because mine sure doesn't. With AC on, the idle speed will drop to around 300rpm in Drive, like when sitting at a red light for example. Surely this isn't normal operation...is it?
View 4 Replies
My 88 F150 (300 six, 5 speed, dual tanks, 176,000 miles). The truck has the low pressure fuel pumps in the tanks and the high pressure pump on the frame rail setup. Truck starts fine, but cuts out severely under acceleration for the first 30 seconds of driving. After that I only notice the problem when applying a lot of throttle (does not cut out under gradual acceleration) or climbing steeper hills. If I kill it for a few minutes and then take off again the problem is back for the first 30 seconds or so. I have replaced all the tune-up type stuff (all filters, plugs & wires, dist. cap & rotor, ignition coil, o2 sensor, cleaned throttle body, replaced IAC valve, numerous sensors). Timing is dead on at 10 deg. BTDC with SPOUT unplugged. My FPR was bad so I also replaced that. Condition exists regardless of which fuel tank I am using (no problems with tank selector).
Getting no KOEO codes, but getting KOER code 41 and plugs do seem to show a lean condition possibly. I'm still averaging around 16 MPG since this became a real problem about 3 months ago.
I removed the bowl from the reservoir between the tanks and the high pressure pump on the frame. No filter in there, but it was clean with no gunk or sediment found. I removed the line from the inlet side of the high pressure pump and found that while cranking the engine I have fuel flowing freely (same amount of flow regardless of which tank I've switched to). The flow was steady, but not extremely strong. If I understand right the in-tank pumps are not designed to provide much pressure? Below is what I found at the schrader valve:
key on, engine off - high pressure pumps runs for about 1 second, brings gauge up to 48 psi
idle, FPR connected - 40 psi
idle FPR disconnected - 52 psi
revving throttle with FPR connected - 46 psi maximum
Connector, where fuel pump relay plugs in, seems to be clean and not corroded at all.
View 14 Replies
I picked up a 90 f150 with the 302. it wont idle without a little throttle, so after a quick look under the hood i noticed alot of broken torn and missing vacuum lines. Where I can get some sort of diagram for routing?
View 1 Replies
