Ford Fuel System :: 1990 F150 Won't Idle Without A Little Throttle
Dec 12, 2010
I picked up a 90 f150 with the 302. it wont idle without a little throttle, so after a quick look under the hood i noticed alot of broken torn and missing vacuum lines. Where I can get some sort of diagram for routing?
View 1 Replies
Advertisement
My truck is a 1990 Ford F150. It seems like when I let it sit for a few min that the gas just drains back into the tank and there for it wont start up that fast, it takes a while to get it going but when I shut it off and start it back up its like a new truck. It starts right up!!! Any tips on what might be wrong, maybe the gas cap is letting pressure out? Im 17 and my dad knows alot about trucks but he cant tell whats wrong.
View 1 Replies
1991 F150XLT, 5.0, E4OD....Should the EFI system bump up the idle speed when the AC system is operating to compensate for the compressor load? Obviously I'm asking because mine sure doesn't. With AC on, the idle speed will drop to around 300rpm in Drive, like when sitting at a red light for example. Surely this isn't normal operation...is it?
View 4 Replies
I have a 1984 Ford F-150 with an I6 engine and a motorcraft carburetor. The truck absolutely will not idle. So I got to looking at the carburetor, and found this red hose going from the carb to a metal pipe, the pipe was just dangling there not connected to anything, and the end it rusted off. I'm pretty sure I know where the other end is supposed to go to, I just don't know how to get there as obviously I am missing some parts and I can't find them so they must have been lost on the road somewhere.
Here's how it looks:
The end of the pipe:
Where it is supposed to end (I think)???
View 1 Replies
I have an ambient temp switch connected to the vac port on my throttle emissions control solenoid for my 2150 carburetor. It's a 78 F-150 with a 5.0L 302, automatic 2WD. Would a bad ambient temp switch screw up my idle? I've disconnected the vac hose and it won't idle at all, and it does the same thing when I disconnect the two wires from the ambient temp switch. If I leave everything alone, I can get the idle down to around 1800rpm, but any lower than that and it stalls.
Is it possible to swap out this throttle emissions control solenoid with another type? I've looked everywhere and can't find an exact replacement, and I have no instructions on how to tune it.
View 4 Replies
Carburetor: Autolite 4100
Fast Idle Speed: 1250 RPM
Curb Idle Speed: 600 RPM (At normal operating temperature)
When I cold start my truck, the fast idle speed holds the throttle at 1500 RPM. I will let it idle about 30 seconds or so, and then I will tap the gas to bring the idle down.
When I do this, the idle will immediately drop all the way down, and too low for a cold engine. The engine won't stall, but it will hover just below 500 RPM, which is a bit too low to idle smoothly.
But when the engine is at operating temperature, the idle speed is 600 RPM and the engine will happily idle smoothly.
Shouldn't there be an "in between" speed? When I tap the gas pedal at 1500 RPM to bring the idle down some, shouldn't the speed drop down a little lower, like 1000 RPM since the engine is still a bit cold?
If so, what do I need to adjust? The Autolite 4100 works PERFECTLY otherwise.
View 1 Replies
My '90 E250, open road, mini motorhome , says on the radiator mount , that there is a Fuel shutoff switch that may have been activated.... I don't have the manual for it, so I need finding the switch, so I can reset it ....The vehicle sometimes starts after about 2 mins with the ignition on, but today won't start, even after a longer wait. Both tanks are full...Fuel gauge not working , in either front or rear position. I can hear the rear pump,in the tank, but can not hear the front one....When I bought it last year, it ran fine after waiting to start, and both positions worked , no stalling , or shutdown.Came home about 95 miles, and it's been parked almost all the time since. I want to start it up weekly , but am having that same problem ...Today was the first time I could see the Fuel Pump Shutoff warning ...but can 't find the darn switch to try resetting .....
View 1 Replies
1990 f150
I have a leak in my rear fuel tank, the front tank has been blocked off and is not used, The leak is at the seam of the two part tank, once removed is there a way to seal this? or should I just replace it?
View 2 Replies
My vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
View 3 Replies
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 Replies
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
View 4 Replies
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 Replies
cant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 Replies
Why the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 Replies
for the past week we have been trying to figure out what is wrong with our truck. We recently bought it and it ran fine. Then got in a minor accident just a fender bender and it started acting up so I got towed to garage. First it would run when cold, but when hot fuel pressure would drop to 28 psi.
So I put new fuel pump, it started but still did the same thing hot 28 psi fuel pressure shuts off. So I put regulator on it, then had 0 fuel pressure won't even start. So got a another regulator thinking I got a bad one, still 0. Checked relay, there fine. I'm gonna check lines and see where fuel stops at but everything is new on it.
View 1 Replies
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 Replies
1994 150 300 6. parked truck after lunch finished work and it wont start no fuel comes out of the valve. Can't get the pump to work even when jumping the 6 pin. heard the relay click still nothing. Checked the inertia switch it wasn't popped. Took the pump out jumped it straight from the battery pump works . I know there has to be something i am missing...
View 7 Replies
I'm looking at replacing the fuel lines in my 94 F150 and the big question is what to do with hooking up to the fuel lines coming out of the fuel pump hat and the fuel rails? Ford uses a specialized pressure fitting on it's custom fuel lines. I think there may be some third party fittings that would replace these, but I'm not sure. I could use a standard hose and cable clamps, but I just don't trust that kind of connection for a fuel line.
View 5 Replies
I have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...
View 2 Replies
I got a problem with the injectors there getting power but no pulse, what do i need to do to trace the problem, not sure what to do next!
View 7 Replies
I have a 1990 Aerostar 4WD, 4L, with about 120k miles. About 6 months ago I started my van and noticed under it that gas was dripping onto the exhaust at the Y-joint and evaporating. I shut off the van and drove another car to work. That evening with fire extinguisher at hand I drove my car up on ramps and quickly got under it looking for the leak. NOTHING. 6 months later...yesterday. I drove for a few blocks from home and notice heavy gas fumes etc. Stopped the van and again gas was dripping onto the Y-pipe joint.
This was an explosive situation... I pulled off the doghouse cover and saw, smelled and touched gas friom on the right top of the engine near the back. My questions are: What could randomly be leaking at this location and is it fixable without pulling the engine. I pushed the van to a secure location and am afraid to turn it on. Maybe I will drain the gas tank before then. I am just now trying to find the schematics for the fuel line delivery stuff. Where to go for a manual.
View 3 Replies