Ford Fuel System :: 1984 F150 - Truck Absolutely Will Not Idle
Jun 21, 2009
I have a 1984 Ford F-150 with an I6 engine and a motorcraft carburetor. The truck absolutely will not idle. So I got to looking at the carburetor, and found this red hose going from the carb to a metal pipe, the pipe was just dangling there not connected to anything, and the end it rusted off. I'm pretty sure I know where the other end is supposed to go to, I just don't know how to get there as obviously I am missing some parts and I can't find them so they must have been lost on the road somewhere.
Here's how it looks:
The end of the pipe:
Where it is supposed to end (I think)???
View 1 Replies
Advertisement
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 Replies
My truck is a 1990 Ford F150. It seems like when I let it sit for a few min that the gas just drains back into the tank and there for it wont start up that fast, it takes a while to get it going but when I shut it off and start it back up its like a new truck. It starts right up!!! Any tips on what might be wrong, maybe the gas cap is letting pressure out? Im 17 and my dad knows alot about trucks but he cant tell whats wrong.
View 1 Replies
1991 F150XLT, 5.0, E4OD....Should the EFI system bump up the idle speed when the AC system is operating to compensate for the compressor load? Obviously I'm asking because mine sure doesn't. With AC on, the idle speed will drop to around 300rpm in Drive, like when sitting at a red light for example. Surely this isn't normal operation...is it?
View 4 Replies
I have a 92 f150 w 302 . My front tank leaks out of the gas cap and builds up pressure. Even though I have never put fuel in it (owned it 7 mos). I siphon fuel out of it weekly. If I switch from rear to front. The truck stalls out.
View 1 Replies
I picked up a 90 f150 with the 302. it wont idle without a little throttle, so after a quick look under the hood i noticed alot of broken torn and missing vacuum lines. Where I can get some sort of diagram for routing?
View 1 Replies
I have an ambient temp switch connected to the vac port on my throttle emissions control solenoid for my 2150 carburetor. It's a 78 F-150 with a 5.0L 302, automatic 2WD. Would a bad ambient temp switch screw up my idle? I've disconnected the vac hose and it won't idle at all, and it does the same thing when I disconnect the two wires from the ambient temp switch. If I leave everything alone, I can get the idle down to around 1800rpm, but any lower than that and it stalls.
Is it possible to swap out this throttle emissions control solenoid with another type? I've looked everywhere and can't find an exact replacement, and I have no instructions on how to tune it.
View 4 Replies
Engine is a late 60's 390 with a C6 auto in good shape with a purported rebuild of about 10-15K miles on it. I picked up a nice condition Autolite 4100 and rebuilt it. Original tag states "C5AF AV" and below that in smaller font: "A 5AC" The base is stamped 1.12. It has the auto choke and auto tranny kickdown.
Truck has been sitting for 4 years so I drained the gas, primed the oil and added 5 fresh gallons. Started up on the second try!! But it won't idle and wants to die unless I feather the gas until it warms up. Also has a bog when accelerating up past 1200 RPM. I've been checking for vacuum leaks but none so far found.
I have a number of questions. But one of the areas I believe I need to correctly adjust is the float level, and here is where I can't get a clear answer or clear explanation of the correct procedures. What is the correct float level? My Sorensen rebuild kit actually had multiple values and the one that looked best had different primary and secondary values. I tried setting it "dry" by the upside down check with the cardboard supplied gauge. Good news is that it is not overflowing so needles and floats seem to be working correctly.
However, how do you do a more accurate wet setting? Appears to be two methods - one is the float setting and the other is the fuel depth. One good thread seems to state that both wet floats should be at 11/16". An engine builder locally said they should both be about level/parallel. Autozone says the primary should be 20/32" and the secondary should be 1 1/16". My rear wet float is almost level and it measures about 15/32". NONE of the data I've been able to find agree on the right setting nor do they explain in detail the correct way to measure using the wet float method.
I've got more questions like the choke settings and the vacuum port for hot air intake (currently open) and only getting 14 inches vacuum (I believe it should be 18 inches) etc., but I'd like to get the floats right before tackling them.
View 12 Replies
I have a 1984 jayco mini 25 with a 7.5(460)in it. It has been in storage for the past 3 years and has not been started. It turns over and I do get spark. The problem is fuel. I am getting power when I jump the oil pressure switch and ground at the wires on the frame rail that go back to the tanks. My gauge does not work on either my front or rear so at first I thought it just may be as simple as a bad ground since the ground is used for fuel level as well as the pump but I wasnt that lucky.The tank switch is working, I can hear it. What are the odds of both fuel pumps being bad?
View 2 Replies
I have an 07 F150 with the 4.6L engine and i was wondering if theres any need to clean my injectors at 30,000km the truck seems to vibrate at idle but not very noticeable seems like a regular v8 rumble but two ppl have pointed it out recently and have riden in my truck a bunch, should i be puttin some injector cleaner in my fuel?
View 3 Replies
My vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
View 3 Replies
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
View 4 Replies
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 Replies
cant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 Replies
Why the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 Replies
for the past week we have been trying to figure out what is wrong with our truck. We recently bought it and it ran fine. Then got in a minor accident just a fender bender and it started acting up so I got towed to garage. First it would run when cold, but when hot fuel pressure would drop to 28 psi.
So I put new fuel pump, it started but still did the same thing hot 28 psi fuel pressure shuts off. So I put regulator on it, then had 0 fuel pressure won't even start. So got a another regulator thinking I got a bad one, still 0. Checked relay, there fine. I'm gonna check lines and see where fuel stops at but everything is new on it.
View 1 Replies
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 Replies
1994 150 300 6. parked truck after lunch finished work and it wont start no fuel comes out of the valve. Can't get the pump to work even when jumping the 6 pin. heard the relay click still nothing. Checked the inertia switch it wasn't popped. Took the pump out jumped it straight from the battery pump works . I know there has to be something i am missing...
View 7 Replies
I'm looking at replacing the fuel lines in my 94 F150 and the big question is what to do with hooking up to the fuel lines coming out of the fuel pump hat and the fuel rails? Ford uses a specialized pressure fitting on it's custom fuel lines. I think there may be some third party fittings that would replace these, but I'm not sure. I could use a standard hose and cable clamps, but I just don't trust that kind of connection for a fuel line.
View 5 Replies
I have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...
View 2 Replies
1984 Ford F-150. Yesterday, began to shutter like a screen door in a hurricane at 35 MPH. I hit the brakes, it pulled hard left. Figured some catastrophic failure of my brake system. Pulled over. Had it towed to mechanic. Mechanic says both front discs have to be replaced (calipers, pads, brake lines). Seem reasonable? Something about sticking calipers and warped discs, etc..
View 4 Replies
