Ford Fuel System :: 1977 - Engine Keep Running With Foot On Pedal?
Jul 3, 2015
Have a 1977 ford f150 with 351m with a motorcraft 2150. Had ( who I believe was a reliable source ) rebuild carburetor for me and after putting back on I can only keep engine running with foot on pedal. I turn idle mixture screws all way in and then proceeded to back out equally. This does not appear to be doing anything. I did turn the choke 2 notches to lean and was able to get it to idle but it wasloping so bad i shut it down and put the choke back to the middle setting.
View 13 Replies
Advertisement
I have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 Replies
When depressed the break peddle is firm, when released break peddle does not return, replaced mc and booster, bleed breaks. Still having same problem.
View 1 Replies
I just had a former Ford tech rebuild my motorcraft 2150 2v on my '77 F250. I took it home, put it back on the truck and it ran kind of rough. I then went ahead and screwed both idle mix screws in untill seated, then back out two turns. The truck ran great, turned off truck then when it the house for dinner. Half an hour later I come back out...truck will not start, just sits and cranks. Finally got it started and it ran good, but crapped out after it warmed up. I have made sure there were no vac leaks when truck was running the first time. Did I adjust the mixture right?
The truck is a '77 F250 400/C6
View 2 Replies
I noticed last night while messing with my truck that I have a constant small spark on my throttle linkage on my carb. BTW, it's a 77F250 with a quick fuel Ethanol carb with an electronic choke. That really probably don't make a difference anyway. Is this a common thing and do I need to run a grounding wire from the carb to the rest of the engine?
View 2 Replies
What to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.
Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.
Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.
The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.
Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.
What would my next step be? Where should i look next?
1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.
View 2 Replies
My engine is running rich, flooding? My truck is a 1986 F-150 302 EFI. The engine idles rough, black smoke and soot comes out the exhaust pipes, and black soot on spark plugs. Symptoms seem to disappear if I throttle the engine and hold it, but as soon as I release the throttle the symptoms reappear and in most case causes the engine to die. These symptoms have just started a week ago. What the problem is.
Fuel injectors are cleaned and rebuilt. New plugs and wires. All new fuel pumps and filters. New air filters. New fuel pressure regulator. New dual function reservoir. New 3-piece timing set. New O2 sensor. New EGR Valve and sensor. New idle air control valve. New distributor, cap, and rotor. New ignition coil. New high volume oil pump. New alternator. New pcv valve. New knock sensor and air charge temp. sensor.
View 14 Replies
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
View 2 Replies
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 Replies
The pumps at times will function what appears to be normal. At other times the pumps will not stop running and it is at those times when the engine does not like to run.
I do not know if the engine will not run due to too much pressure or not enough fuel pressure. The problem is with both tanks and pumps so I do not believe the problem is inside either of the tanks.
One problem is that I just got the truck and the prior owner had at times done a little work and you know how that can be a problem. He could have done some damage to some hoses or who knows what. He had replaced the radiator and the left side exhaust manifold recently, though at different times. He thinks the problem started around the time he did the radiator. I know it doesn't make sense but things can get bumped or damaged.
What would the problem be that it could come and go? I drove it for a few miles and I thought that maybe the problem had gone away after I replaced what appeared to be a short vacuum line by the throttle body. But the problem still comes and goes. Now the truck is stuck till I figure the problem out.
View 2 Replies
As the title says, I have an 02 Supercrew with the 5.4. The engine starts when cold and runs fine but sometimes when I start it hot after running for a bit, it will stall out unless I keep my foot on the gas pedal. This seems to only happen on hot days. It was about 90 F here yesterday and I drove it to a shopping mall after supper - maybe 5 miles. It sat for maybe 20 minutes and when I re-started it, it stalled out.
The tach needle just drops slowly to zero and the engine stops. It will re-start without any problem but will only keep running if I keep my foot on the gas and keep the revs up a bit. It has done this a few times in the past few years and only on hot days after it has been running and then sat for a few minutes.
What I should look at? It does not throw any codes and generally runs ok after a few minutes. For example, last night I managed to keep it going by shifting into neutral when required until I got back on the road. I drove 2 or 3 miles and at the next light, it acted like nothing happened.
View 1 Replies
Changed timing belt after several teeth being stripped. Engine runs but won't idle without foot on gas pedal. Drives smooth as long above 2000 rpm. Thinking there is one or more slightly bent valves. Quadruple checked timing marks. Coils are good. Fuel injectors are good. Spark plugs are new NGK's. DTC's are 0300, 0301, 0302, 0303, 0304 - misfiring.
Have a line on a low mileage head with warranty. 2007 Accent 1.6L?
View 9 Replies
I drive a '99 Chevy Tracker with the 2Liter engine, a 5 speed manual transmission and 110K mi. on it. When I lift my foot from the throttle pedal in preparing to shift gears the engine takes a very long time to reduce it's RPM. This is a problem, when up shifting, as the transmission is spinning too fast for smooth gear engagement.
The engine idles normally under all other circumstances. It is only slow to decelerate whenever I lift my foot from the throttle pedal. This makes up shifting very slow and/or causes the gears to sometimes grind slightly.
View 3 Replies
I built the 400 in my 79 a couple years ago and it runs very well...until yesterday. I'm about 80 miles into this tank, and on my way home from work, I thought I felt a vibration (not in the steering wheel, but in the front oc the truck). Then the engine became evident it was running rough and was skipping and surging. I stopped.
It idled pretty rough, then died. Fired right back up, ran rough, and died. Sometimes it would idle smooth for several seconds (20-30) then start surging and skipping and die. I could hold a little throttle and it would run about the same, except some backfiring in the exhaust (more like a big hiccup).
The carb is a 670 Street Avenger with nothing really done to it. The bores are really black (not sooty, more damp or so). I have always used the air filter, so that's odd. I took the carb off and removed the bowls. Nothing inside has a dirty or clogged appearance at all. Not sure if I should completely rebuild it.
View 6 Replies
My brake pedal is sticking down every time I push it in. I tried replacing the spring that was in there with a stronger one and sprayed the whole unit down with an all purpose silicon lubricant. It seemed to work a little but the problem is far from solved. It seems like it is sticking somewhere further away from the pedal. Master Cylinder maybe? I selected Tacoma because it's the closest option to my truck, but it's actually a 77 pickup/hilux.
View 4 Replies
I have a 77 ford f100 I am restoring. I have two factory am/fm radios. I bench test both with antenna male plug all the way in, and the fm works fine on both radios. The only way to get am to work, is to slide the male antenna plug all the way out till it is just touching, then if I jiggle it, the radio plays.
View 1 Replies
I have a 1994 f 150 5.8l 4x4 with 215000. Cold starting is fine runs well. After running it will not start after shut down. Wait till motor cools back down will start up and run fine ....
View 2 Replies
I have a holley 390 cfm carb on a 78 F250, 300 I6 with headers and an offy dp intake. Somewhere i am getting way too much fuel to the engine and it is sputtering and smoking bad. I have checked the float level, needle and seat, and power valve. All seemed ok but i replaced the power valve and needle and seat on the primary side just to be sure. Even with the float level adjusted way low and the idle mixture screws turned way in the truck would still sputter and spew out black smoke at idle and all throttle positions. I can't figure out where the gas is coming from. I checked to make sure the butterflies were closed and they were. I looked down the throat of the carb when it was running and didn't see any gas rushing in. When i take the carb off the bottom is soaked and the gasket and spacer is all soaked and theres gas sitting in the bottom of my intake. Where is this gas coming from?
View 14 Replies
Is it fair to assume that my filter is clogged when I turn over the engine and fuel does NOT come out of the filter with the uphill line disconnected. I was able to disconnect the rear line from filter and fuel DID pump out of line when I cranked it over. Been dealing with a crank no start, I'm in the process of trying to test my CPS properly but not sure if I'm testing it right.
2000 f 150 4.2 v6 232,000 miles....
View 7 Replies
I am unable to get fuel delivery from tanks to engine in normal operation. I can however get pumps working with jumper wire to them. It will start with ether but not stay running on it's own. Could this be a relay or something in tfi thing ?
View 14 Replies
I'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister, there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one. It's a 2007 Ford 4x4 6.0 diesel.
View 2 Replies
