Ford Fuel System :: 1963 - 2100 Carburetor Won't Idle?
May 6, 2008
I rebuilt a 1963 ford 2B crburetor with manual choke. Put the carburetor on and it runs very rough. Won't go below 800 rpm or it dies and I need to choke it to start. Thought it was a vacumn leak so sprayed WD -40 and no change in idle. So pulled off the carburetor and put on the previous carburetor (with electric choke) and it runs great. I want to use the manual choke to hook up the cable though. I replaced everything in the carb. What do you think it is?
View 5 Replies
Advertisement
I have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 Replies
Thought I would check and see if it's possible to store a Carburetor. Have a Holley 4160 that I rebuilt and would like to keep as a backup. Thought since the carb has not been installed the gaskets and seals may not be an issue. Other option, swap the Carb on my truck every few months.
View 4 Replies
I have gas leaking from the pump diaphragm assembly cover of the motorcraft carb,2BBL,360,75,auto.Is this easily repairable,or is a new carb in my future?
View 4 Replies
I picked up a renamed 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. Are these parts still produced and if not is there another way to make it work?
View 10 Replies
Would like to replace the 2 1/2" aluminum ported 4bbl spacer down to an inch or so. Finding it difficult locating 'ported' aluminum spacers, however, there are several brands of the 'composite' type?
View 4 Replies
I picked up a remaned 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. I can't find anyone who carries it, let alone knows what it is. Are these parts still produced and if not is there another way to make it work?
View 13 Replies
I have a 74 f250 with a 67 352 and a 2150 carb. I have noticed that after driving the truck for a while and when its nice and hot, if I shut it off I hear a funny "howling" noise coming from the carb. It does it for about 5 seconds, then goes away. I rebuilt the carb and it still makes the noise. Also when I am driving it, when I have the pedal at a certain point, I can hear a lot of vacuum, I have checked for vacuum leaks, and there are none. The other question I have is, the 352 was out of a standard shift truck, mine is an auto, so I have nowhere to hook my tranny kick down rod to. How I can fix that, besides replacing the carb?
View 3 Replies
i just got my edelbrock performer rpm intake and my holley 4 barrel installed but it won't run...the only way i can get it to hit and run at all is to floor it like it's flooded...then it'll run for a second but will never rev up and get going like it should...so i watched some vids on youtube for setting mixture on holley's wich i was pretty sure about anyway...turned the idle mixture screws in to snug and then out 1 and a half turns. is this a symptom of a bad vacuum leak or is it something to do with the carb maybe not enough fuel?
it's a holley 4160...list-6619...which is 600 cfm...it's on a 302 with 3 speed.
View 2 Replies
Engine is a 69 390, fresh rebuild by the PO... Aluminum intake manifold and new Edelbrock 4bbl Drop in Crane ignition.
Runs great... Except when its warm out, or even on cold days when its warmed up after a substantial drive..
AT that point here is what happens: No issue until I shut it off then it diesels badly, THEN.. When I restart it will not idle, dies.. If I keep my foot on the accelerator it will keep running, but not well.. If I let it run for a good while, 5-10 mins, it smooths out... Consistently acts like this .. Again.. Not when the engine is cold, and not on a cold day until it really warms up..
I suspected a vacuum leak? Replaced any suspicious vac tubing.. Cant get to the AT modulator easily, have not checked it yet?? Also suspect the intake manifold??
View 19 Replies
Last night I decided to see if I couldn't do something about my leaky carburetor in my 1983 ranger. It's a motorcraft 2150 carb. I took it all apart and followed a guide to clean it, then put it all back together and reinstalled it today. Unfortunately my truck won't idle, makes a whiny noise, and acts odd with the accelerator.
I've got a video posted here : 1983 Ranger Carb troubles - YouTube ....
View 10 Replies
I have a 98 Grand Cherokee (V-8) with 127K on it, that sometimes during cold starts acts like an old carburetor system with the choke sticking. It floods, chokes, it sputters, and you have to maintain an RPM of about 2000 to keep it running and get it to snap out of it. A local shop did a tune up on it before this problem started to happen intermittently, aside from this, it seems to run well. I took it back to the shop and they did several diagnostic tests and even got it to do it for them while they had it.
I told them that it seemed like if we released the key from the start position as soon as it began to fire, the problem would happen, if we held it I the start for a bit longer we could usually avoid it. They returned it to me saying that "Yup, if you hold the start position longer it won't happen, and by the way here is a bill for $103." With the recent below zero temps, it's getting worse, almost unavoidable. My wife says it uses a lot of fuel when this is happening but we have not actually tracked the mileage. Other than this it's a great car but I'm ready to drive it off a high mountain cliff.
View 4 Replies
1991 F150XLT, 5.0, E4OD....Should the EFI system bump up the idle speed when the AC system is operating to compensate for the compressor load? Obviously I'm asking because mine sure doesn't. With AC on, the idle speed will drop to around 300rpm in Drive, like when sitting at a red light for example. Surely this isn't normal operation...is it?
View 4 Replies
I have a 4160 on a 351 Ford. I confess, it's a boat!
I had a major flat spot when accelerating off idle. I found it wasn't pumping on the accelerator circuit.
I replaced the accelerator diaphragm and cleaned the squirts and the passages. It squirts great now, but if I floor it, it completely bogs. If I baby it really carefully, once the engine gets over about 1800 rpms, it acts fine.
I thought it over, checked the travel on the arm that presses the diaphragm, and figured my pump cam was worn. It "seemed" like the duration of the squirt was not long enough.
I got a new cam kit. The orange cam on my carb was not a bit worn compared to the cam in the kit. Not encouraging. I put the only other cam in the kit that I thought might work. It was blue, and it gave more lift but no greater duration. It did not make any difference that I can tell. Is there a transition circuit I might have problem with? I don't know enough to go any further.
View 9 Replies
I picked up a 90 f150 with the 302. it wont idle without a little throttle, so after a quick look under the hood i noticed alot of broken torn and missing vacuum lines. Where I can get some sort of diagram for routing?
View 1 Replies
I have a 1984 Ford F-150 with an I6 engine and a motorcraft carburetor. The truck absolutely will not idle. So I got to looking at the carburetor, and found this red hose going from the carb to a metal pipe, the pipe was just dangling there not connected to anything, and the end it rusted off. I'm pretty sure I know where the other end is supposed to go to, I just don't know how to get there as obviously I am missing some parts and I can't find them so they must have been lost on the road somewhere.
Here's how it looks:
The end of the pipe:
Where it is supposed to end (I think)???
View 1 Replies
Its an 88 F-250 4x4 with a 302 EFI 5-speed. Fair compression, runs smooth. When I press the gas pedal it takes about 5 seconds for the old girl to return to idle. I know nothing about EFI. My buddy,s out of town with the hand held mechanic. Is there anything I could check till he gets back.
View 6 Replies
Engine is a late 60's 390 with a C6 auto in good shape with a purported rebuild of about 10-15K miles on it. I picked up a nice condition Autolite 4100 and rebuilt it. Original tag states "C5AF AV" and below that in smaller font: "A 5AC" The base is stamped 1.12. It has the auto choke and auto tranny kickdown.
Truck has been sitting for 4 years so I drained the gas, primed the oil and added 5 fresh gallons. Started up on the second try!! But it won't idle and wants to die unless I feather the gas until it warms up. Also has a bog when accelerating up past 1200 RPM. I've been checking for vacuum leaks but none so far found.
I have a number of questions. But one of the areas I believe I need to correctly adjust is the float level, and here is where I can't get a clear answer or clear explanation of the correct procedures. What is the correct float level? My Sorensen rebuild kit actually had multiple values and the one that looked best had different primary and secondary values. I tried setting it "dry" by the upside down check with the cardboard supplied gauge. Good news is that it is not overflowing so needles and floats seem to be working correctly.
However, how do you do a more accurate wet setting? Appears to be two methods - one is the float setting and the other is the fuel depth. One good thread seems to state that both wet floats should be at 11/16". An engine builder locally said they should both be about level/parallel. Autozone says the primary should be 20/32" and the secondary should be 1 1/16". My rear wet float is almost level and it measures about 15/32". NONE of the data I've been able to find agree on the right setting nor do they explain in detail the correct way to measure using the wet float method.
I've got more questions like the choke settings and the vacuum port for hot air intake (currently open) and only getting 14 inches vacuum (I believe it should be 18 inches) etc., but I'd like to get the floats right before tackling them.
View 12 Replies
I have an ambient temp switch connected to the vac port on my throttle emissions control solenoid for my 2150 carburetor. It's a 78 F-150 with a 5.0L 302, automatic 2WD. Would a bad ambient temp switch screw up my idle? I've disconnected the vac hose and it won't idle at all, and it does the same thing when I disconnect the two wires from the ambient temp switch. If I leave everything alone, I can get the idle down to around 1800rpm, but any lower than that and it stalls.
Is it possible to swap out this throttle emissions control solenoid with another type? I've looked everywhere and can't find an exact replacement, and I have no instructions on how to tune it.
View 4 Replies
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
View 9 Replies
I have an 07 F150 with the 4.6L engine and i was wondering if theres any need to clean my injectors at 30,000km the truck seems to vibrate at idle but not very noticeable seems like a regular v8 rumble but two ppl have pointed it out recently and have riden in my truck a bunch, should i be puttin some injector cleaner in my fuel?
View 3 Replies
