Ford - Freestar :: 2004 - Misfire / Computer Code Is P0302
May 25, 2011
My 2004 Ford Freestar SEL (the 4.2L version, 123,000 miles) is missing. The computer code is P0302 which, from what I can find, indicates a misfire in cylinder 2. I had this same code at 99,000 miles and ended up having the spark plugs and wires replaced around 100K miles. It was all running fine until about a month ago and started misfiring again, badly. I thought it was related to the rain but it is doing it all the time now. At times it gets so bad, I have no power and the computer disengages my A/C (bad at this time of the year). I tried a running a fuel system cleaner that specifically mentioned cleaning the injectors, hoping the problem was simply a clogged injector, to no avail (I know I probably wasted my $10 here). I have a couple of questions:
1. Am I doing damage to the engine or transmission by continuing to drive it? I really don't have a choice but need to know how urgent it is.
2. Does this thing have a traditional distributor cap & rotor or is there an electronic ignition module the plug wires connect to?
3. Where would I find the illusive distributor or ignition module, in theory?
4. Any other theories as to the cause of the misfire (cheapest first)?
View 5 Replies
Advertisement
I have a p0300 code coming up on the comp. The motor runs fine until it gets wet. rain/carwash. I have tried to spray each coil with water and could not get it to misfire. Then I brought out the water hose and sprayed it top of the motor this found the misfire. This thing has 8 coils and I really don't want to replace them all. My Question is there some thing else that could be causing the misfires.
View 14 Replies
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
View 14 Replies
I have a 2005 Jetta 2.0 BEV GLS. I got a code P0302 for misfire on cylinder 2. I am pretty sure it's the Ignition coil. I live in Canada and my autoparts store only has BWD brand. I have read this is a crappy brand.
View 1 Replies
I just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 Replies
2009 Accent, 1.6L 154,xxx Cylinder two misfire. Engine was rebuilt due to timing belt. Twice. Second time I did it. Replaced plugs, coil packs, all gaskets, (everything new in the head) did a smoke test, compression test 180 psi across all four, used a noid light for coil packs (good) did it at the injectors 1,3,4 did good, but 2 came on then went off. Check resistance and it shows good, replaced injector anyway and the connecter. Still doesn't work. Checked powers and grounds at the rail, good. Good solid voltage. I hooked up a scan tool and tried to shut injector 2 off, no change in RPM or vibration. Scan tool worked for 1,3,4. Used another PCM, still misfire in two. Even jumped a wire from PCM control and 15A inj fuse for the 12V constant (bypassed the harness) and still doesn't work. Also have knock sensor code, just two codes.
View 14 Replies
I have a new (to me) '97 Windstar with 128K +. C.E.L. is on and intermittently flashing. The code reads P0302 (Cylinder 2 Mis-fire). No other codes are set. Have cleared them many times and gone through multiple drive cycles.
Description of issue: After clearing the codes, and indeed upon each startup, the car starts and idles smoothly without hesitation or issue. It pulls away from parked position without issue. Appears to accelerate just fine. In stop-and-go traffic or directly onto the highway it seems to run smoothly without problem. After a period of time (I don't believe it to be consistent), it will start to misfire and the C.E.L. will be set. If it is still misfiring, the light will flash.
Here's the weird part...when stopping at a traffic light or just continuing to drive on the highway, the misfire will resolve and the car will run smoothly again. The C.E.L., trailing the condition by a bit, will go to solid from flashing and will remain that way until a little farther down the road. The misfire never seems to be more than one cylinder and the trouble code seems to bear that out. Just idling, the car will return to smooth operation and it seems to have smooth acceleration. In other words, the misfire seems to go away under acceleration.
What I've done: I've replaced plugs and wires. No change. Replaced Coil pack. No change.
Next steps: Next steps seem to be looking to fuel or air. My concern with that approach is the occasional nature of the problem. Compression problems would be consistent across the board, right? That cylinder would always be a problem. Same thing for fuel (fuel pump and/or filter). All cylinders would have the problem and it would have issues starting. OK, next thing--injector. Would an injector have spotty performance like this? Also, could it be related to the EGR ports on the intake on this vintage Windstar? (Once again, is an intermittent problem consistent?) Finally, since the primary circuit for spark is controlled by a PCM pin setting a ground for each cylinder, could the PCM, or wiring, be the culprit?
View 6 Replies
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
View 3 Replies
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
View 8 Replies
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.
View 4 Replies
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 Replies
Getting error code p0302, misfire in 2, pulled the plug and had oil on the treads and on the lower part. My guess is the valve cover gasket, but I'm not 100 percent sure.
View 18 Replies
2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
View 3 Replies
2005 3.5L FWD. 5 days ago I left the house, the engine was running smooth at idle but having hiccups when accelerating. Check engine light went on when accelerating but going off at idle. Turned around at the first stop light, parked the car home and pulled code P0302 misfire on #2 . Figured it's most likely the coil, was going to order one next day but to my surprise, no more check engine light next day and engine has been running smooth since then. Probably drove 100 miles since with no issues. I have 6 spark plugs waiting to be replaced but it's too cold to do it right now unless it's an emergency. Car has 105k miles now, spark plugs were changed at 63k. Was this just a fluke and P0302 will probably not come back or should I not risk it and just go ahead and replace the coil? If I end up replacing the coil, should I do one coil or all three?
View 22 Replies
1997 Ford Ranger with 190K miles has check engine light on with P302 computer code, meaning misfire on cylinder 2. Engine runs rough at idle only once it warms up, which only takes a minute. It is usually fine while driving, but it's a lot easier to feel a misfire at lower RPMs than at higher ones. Added fuel injector cleaner to gas for a couple tanks, no change. My mechanic has checked spark plugs, fuel injector, o2 sensor, and everything is ok. Dry compression test shows good compression. He thinks it may be a valve sticking, which means a valve job: expensive. Is there anything else that can be done? Why is there no misfire when it is first started?
View 9 Replies
This has been an ongoing issue with our 2006. We purchased the car about a year ago and have put on just over 8,000 miles. Rebuilt the battery pack and replaced the 12v battery. This is my wife's car and I have a 2005, so I have done some diagnostics, tuneup, and even swapped some parts between the two cars trying to narrow down the issues.
Only recently have codes been recorded. The car is has a noticeable misfire at low RPM. Here is what has happened up until now:
11/29/15 - replaced spark plugs - #1 was fouled so I swapped coils between cylinders 1 and 4
2/25/16 - replaced 12v battery with new battery
4/1/16 - P0300, P0301 codes were first recorded and reset to see if they came back
4/10/16 - swapped Integration Relay with my 2005 (part # 82641-47010). My 2005 ran poorly after the swap, so I put a used one in my 2005.
View 19 Replies
My prius is almost mint, with 226k on it. I just recently got a code from it P0302, so I thought I'd check the fuel injectors, I took them out and cannot reinstall them without them leaking all over.. I removed and replaced new orings on the top and cranked down the bolts really hard and still a bunch leaking. Is there a trick I should know about?
View 3 Replies
2000 Ford Ex 5.4 V8 175K miles
Top of radiator (plastic part) had a small crack and started leaking on drivers side. Fixed with JB Weld. Ran fine for a day. Now I have a bad misfire and codes P0301 and P0302 (Cyl 1 and 2). Cleaned MAF and checked Air Filter. All good. Plugs replaced at dealer less than 20K miles ago.
So I took off Cyl 5 (easiest) and found that the boot is fine but the collar on the boot is done for. Can this cause the issue?
View 14 Replies
My 97 F150 4.6 4x4 threw a P0302 and P0401 the other day, I traced the miss fire to a loose injector plug. I reset the codes last weekend, I got in the truck and went to the Dump and to town to pick some stuff up. It threw the EGR code again, so this morning I did a little checking on the EGR I cranked the truck and disconnected the FPR vacuum line and hooked it to the EGR valve and the truck died down but didn't completely die.
Now the green line that went to the EGR valve felt like it had a slight bit of pressure coming from it. Is this normal? I did pull the white feed line from the EGR Regulator and it had good vacuum.
The regulator also makes a humming sound when you cut the truck off. Ill be pulling the alternator this weekend due to it going out last night, while I'm in there if Ive got to pull the throttle body id rather do it while I'm elbow deep in it. So does it sound more like a Clogged Throttle body or a Faulty sensor?
View 4 Replies
My wife has a 2004 Freestar and a few weeks ago it all of a sudden went to red on the temp gauge and there was some steam. So I checked the reservoir and it was too low on coolant. I added the coolant but it still had a tendency to run towards red but turning on the heater full blast made it go down drastically (below 50%). ALso, the heater was blowing cold air. So I changed the thermostat and watched it. It continued to inch up to 70%-80% and then finally drop back down to 40%.
I also had to start adding coolant every other day. I took it in and had a flush done. It eventually blew the reservoir cap off and all the coolant out while my wife was on the highway. I had it towed to a shop and the mechanic said he couldn't find anything wrong with it except the cap. He did a pressure check with the old cap and it wouldn't hold. He replaced the cap and it held pressure. He assumed that was the problem. That was a week ago.
Today it ran up to 80%-90% and then all of a sudden it dropped down to 40%. When we got home I let it cool for 4 hours and then checked the level. It was at the bottom of the reservoir roughly 3-4 inches below the fill line. We don't see any signs of leaking on our driveway. What could the problem be? I checked the oil to see if it may have coolant in it but didn't see any sign.
View 19 Replies
I have a 2002 Camry, 2.4 with 155k miles.
This morning I was going to work and was making a lane change and hit the accelerator quite aggressively. Suddenly my engine started to run really rough and shook the car and the check engine light started flashing.
I checked the engine code and its giving me a P0302 Cylinder 2 Misfire warning.
I have read that there can be various reasons but I figured since this problem is consistent its not a vacuum issue? Could it just be a bad plug? I don't have the tools to fix it, I am going to get them soon to pull the plugs and inspect then, and will replace them anyway since I don't think they have ever been replaced.
View 11 Replies
