I have a really weird issue with my 2003 Ford Focus. Manual transmission, just over 50,000 miles. I've been noticing a stumble or hesitation (like the engine is cutting out) at steady speed, but ONLY when it is snowy out, more if it's windy as well. I don't recall that this happens if it's rainy or foggy. All maintenance is performed as specified, to include air filter changes.
View 9 RepliesI have a 2000 Tahoe with the 5.3L V-8, 351,000 (yes that is correct) miles. Runs great except it has recently developed a stutter, hesitation, skip, I don't really know how to describe it, under acceleration or at steady speed. This is an intermittent problem and it is driving me batty. The only codes are a P0420, maybe after 350k miles it needs replaced? Would that possibly cause this issue, or am I looking at something more sinister?
View 2 RepliesWe have a brand new 2013 Ford Focus, a little over 2500 miles. We drove the vehicle to NYC, starting the trip with over 500 miles. During stop-n-go driving the following conditions are experienced: - car in drive but stopped, engine idles at 750rpm- car moving at crawl speed, less than 5mph, and RPM between 750 to 2100, engine acts as if it will stall (IT IS AN AUTOMATIC TRANS); when this happens there's an obvious shudder - again almost as if the car will stall out- cannot determine what gear its in, but probably first, second, or maybe third, but no higher
We took the car back to the dealer, but they acted as if this was a normal, if not, non existent issue; they were very dismissive.
2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
My daughter's automatic DOHC SE Focus had suddenly been stalling, becoming harder to start and not maintaining a steady idle. I took it to our semi-trusted repair shop and was told it needed an EGR valve, plugs, coil, and ignition wires. $580! These all seemed like repairs I could do and so I have worked through all of these. I replaced the EGR valve and that seemed to make the problem actually worse. (so I put the old one back in) I put in new plugs and that improved the idle a small amount. Then I put in the new coil and that seemed to steady the idle a bit more. But here is what I have discovered through my many test drives after making these incremental repairs: The car starts now from cold very well and runs great for the first 20 minutes or so but...when it gets hot after 15 minutes or so of 50 mph driving, the idle drops and the engine wants to cut off. At low revs it seems to stumble and lose power. I think this is what my daughter was experiencing originally and none of my early test drives were long enough to surface the original problem. I have read that the Idle Control Valve might be a culprit in this sort of behavior.
View 5 RepliesI recently picked up a 2000 Excursion with the 5.4 V8. Engine has 150,000. I got it cheap because it has a surging problem over 1500 RPM. This problem is intermittent.
I have 1 DTC. P1000 which is OBDII checks not complete. I cannot clear this even using the factory procedures. FYI..I have a snap on solus scanner. I think this is a voltage problem, If you try to start the engine with the scanner plugged in, the scanner shuts off, so I'm thinking the PCM loses battery power supply when the starter engages, resetting the PCM.
This problem is NOT a miss.... something isn't opening or shutting off above 1500 RPM. This truck doesn't have an EGR system, it has the EVAP system. This may be the problem, thats why I'm here. OK. heres a list of what I've replaced since I started working on it.
Engine oil and filter
air filter
fuel filter
8 COP's
8 plugs gapped properly
cam position sensor
IAC sensor
MAF sensor
Removed throttle body and cleaned.
Vacuum checks. 22" at purge valve,fuel dia, and vacuum canister
Checking with the scanner at 1500 RPM with problem
SFtrim1% bounces between5-15
SFtrim2% bounces between2-0
LFtrim1% bounces between11-13
LFtrim2% bounces between 5-6
O2S11(mv) bounces between 200-781
O2S21(mv) bounces between 200-800
Ssystem is in closed loop holding throttle at 1500 RPM... Note engine surges when at the RPM or above. I'm thinking the engine is lean, not sure how to read the trim numbers...
Idle is fine ... Problem is intermittent ... Also noticed that engine will only advance spark to 30 degrees @2000 RPM during this problem. I have seen it advance to 38-40 degrees when I do not have this problem, so I kind of understand the power loss,knock etc due to the timing, my question is whats causing it to do this?
EVAP question.... The purge valve should open according to PCM command a certain value, correct? I can monitor the duty cycle % but cannot activate and check proper duty cycle through scanner . When I try to I get an error message of module error -unspecified.
Disconnected hoses at purge valve,Full manifold vacumn on one, nothing on other, no flow through purge valve, but scanner shows 30% duty cycle. I would think the should be a little flow at 30% Maybe my problem? Troubleshoot procedure for the EVAP would be good.
First, a little background on my truck. 2007 with 5.4, 122000 miles, oil changes with 5-20 Motorcraft and Motorcraft filters, plugs done by dealer 40000 miles ago. The truck has developed a ticking noise, kind of like a lifter (I know these engines don't have lifters) that is most noticeable from the side of the truck near wheel. ticking speeds up with the rpm. Also around same time, between 40-55 under load there is a bit of a stumble, but I can gas thru it. I'm guessing these are related. I'm thinking spark plugs again, but shouldn't I get more than 40000 out of them? I might just take it in, since I've got oil leak somewhere around back of the oil pan, but figured maybe might get some clues first. Also, no CEL.
View 4 Replies460, stock RV motor with LT headers, Alum Stealth intake. Carb is brand new, Holley 600 cfm, out of the box.
Elec choke, vac 2nds. Timing is set to 12 BTDC.
Truck idles beautifully. Drop it in drive, it will ever so slightly stumble/hesitate then go liked a raped ape. Has great acceleration (for a 8k dually crewcab). In my mind, I'm thinking a slightly larger than stock accel pump to give a bigger shot.
However, it does have a 1" carb spacer. That and the hi rise stealth, is it leaning out for a sec and causing the stumble? Would pulling that 1" spacer work? I was thinking the higher the carb the better to get less heat dissipation from the engine's heat. Replacing the heater core now. So I have some time to sort it out. I'd like to road test a tank of gas through it, but gotta fix the heater 1st.
A couple questions I have about my truck. I'm still new to the F150.
First, my truck has an Ecoboost and I have a slight stumble/hesitation when you start the truck cold. It clears up within 10 seconds and doesn't seem to affect drivability whatsoever.
Second, it seems that only my driver side mirror has the "dimming feature" to it. Is this normal?
When I'm driving at highway speed and press the accelerator after coasting a bit, the engine stumbles then picks up and accelerates. The fuel bowl assembly is brand new as of 5 months ago, and I drained of any water last month when I changed oil. Truck is stock with 350k miles.
Apart from this issue, it runs well and idles smoothly. Injectors are healthy per a buzz test a powerstroke mechanic performed last year. What could cause the stumble off idle?
My 2011 stick shift no air Accent has a hesitation or stumble on light acceleration that comes and goes. It may not occur for weeks then re-occurs. It is hard to reproduce intentionally. It never occurs in cruise. The CEL is not on. Most often occurs at 1400 to 1500 rpm with slight acceleration or a slight increase in load as coming to a slight hill. I tried injector cleaner a few times and changed air filter. It seemed more reloaded to induction airflow so I changed the MAP sensor. I understand the 2011 Accent does not have a MAF sensor. It is still occurring. It is fine in steady cruise as well as in hard acceleration. I am wondering if it is a TPS sensor problem. It has 60,000 miles and otherwise runs fine.
View 4 RepliesI have a 2004 Pontiac Montana with 90K. If the overnight temperature has been below 40ish, there is a noticeable hesitation or stumble (almost as if the engine cuts out for a second-but never actually stalls out) on the 2 to 1 downshift when braking to a stop while the vehicle is in open loop. As the engine warms up the stumble becomes less noticeable until the temp gauge reaches the 1/4 mark at which point the stumble is gone. It won't return until the following morning - the next cold start. Our mechanic has cleaned the Throttle Body and the MAF- no change. Their transmission guy said he did not think it was a tranny issue. It has no other symptoms and seems to shift normally at all other times. What to do next??
View 11 RepliesI had a motor go bad, overheated, replaced it with another motor. Got it all back together and upon test drive I am having a low rpm (below 3k) bad hesitation/misfire. The engine runs just fine at wide open throttle.
First thing i checked for were plug wires and vacuum leaks. The only difference between the old block and the new block is the fact that i replaced the MAF with a new one, as i was getting a maf code on the old engine. I can't get it to throw a code...
When I take off from a start it will intermittently stumble or hesitate, seems to be around 1500 rpm. have also noted it at higher speed while cruising. its more like a momentary power cut than a miss fire.
So far I have done the following
new fuel filters
clean MAF
new PCV valve
new spark plugs
check all hoses and plugs etc
injector clean
checked techstream for codes. there is one for a heated O2 sensor but dont think thats it.
2002. SC430
I drive a stick Ford Focus 2002 and when I accelerate, the car hesitates/bogs down. This happens more when it is going up and heavily loaded. It happens more on low RPM but it also happens on high RPM. I can accelerate on idle and it does not have any problem. At the same time, I know when this is happening, or about to happen, because the radio volume rises suddenly together with the speedometer needle that goes crazy (up to 150mph) while the car is going at 30mph. The radio volume and speedometer needle settle down after the spurt.
View 9 RepliesMy 93 with 210K miles threw a new one at me the other day. Not 1 mile from work with AC running, it started stumbling a bit at around 40MPH. I just assumed it was the AC cycling and the Van was in OD. Dropped into D and drove her on home.
Well this morning was round 2.... got about 2 miles from home and it started stumbling again (no AC this time). Just happened to look down at my digital dash and the speed was jumping all over, finally settling on 0 MPH. I got about a mile down the interstate and it suddenly reactivated and displayed 70mph.... smooth as silk.
OK, so I know that the rear diff. has a sensor for ABS, and obviously a pulse wheel on the diff. Is this sensor the input for speed? From other makes, I understand the pulse train input is "conditioned" in another device ( hardware) which then outputs to the dash display.
Based on these assumptions, I'm going to assume the crazy speed variation was playing hell with the ECU. When it settled on 0 mph it was happy again. Can't just be a display issue as there would have been no stumble. Getting ready to drive her about 3.5 hours this weekend to go trout fishing.... obviously the cruise won't work but otherwise it appears to function WITHOUT the speed input.
I have an occasional issue when pressing the gas pedal while stopped or at low speed the car hesitates and slightly kicks. It doesn't seem to happen at high speeds. The auto mechanic I took it to said he is getting a read that it might be the thermostat. My temperature gauge has not moved above normal. The auto guy says they need to start with the thermostat and see where we are with the problem at hand afterward. This does not make sense to me. Maybe the electronic read is right and the thermostat needs replacing, but how can this affect my occasional hesitation problem?
View 12 RepliesProblem I'm having, when in overdrive my 04' F150 FX4 5.4 Triton surges while trying to maintain a steady speed during power delivery to the wheels, it causes a shuttering and bucking effect. If I push the button to turn the O/D off, the RPMs rise and problem goes away. During the problem no CEL illuminates and tach stays constant. Fluid condition & level are okay. (not burnt) I'm completely baffled since there is no code in the ECM to point me in the right direction. I do use the truck to occasionally tow my 5k lb boat & trailer. When I began towing I did not know to turn the O/D off and put some miles on towing in overdrive, I know now that was not good for the tranny.
View 7 RepliesI just have a situation that I would like some insight into. I have a 2004 T-reg V6 that jerks while at a constant speed (usually around 40-50 mph). It does it both while cruise is engaged and disengaged. You can also hear a rhythmic "clunk"ing. The jerking and clunking stop if you accelerate or decelerate.
BTW the car is still under full aftermarket warranty from the dealership where we bought it so I would want to try to figure out what this is before the warranty ends.
Our Egg will occasionally surge at steady speeds - i.e it will jerk fore and aft with no change in accelerator pedal settings. This is an intermittent problem that seems worse when ambient temperatures are low. It isn't yet annoying enough to warrant a trip to the dealer (they seem clueless about this car anyway!).
View 12 RepliesWhat would cause a trouble code PO 300 on a 1998 Chevy Blazer. The truck will run good sometimes. When it runs bad it will stumble at low speed acceleration. It will run fine wide open. Dealer looked at it and thought it was egr vale. I replaced it and it runs a little better but still stumbles.
View 5 Replies