Ford - Focus :: 2002 Cylinder 2 Misfire / Stumbles On Acceleration Between 2000 And 4000 RPMs
Jul 8, 2011
I've got a misfire problem with my Focus. It started about a month ago and did not trip a code until last week. It stumbles on acceleration between 2,000 and 4,000 rpms. It is only a slight stumble and although noticeable, it does not impede driveability much. Last week I was able to get it to finally trip an OBD code. P302 - Cylinder 2 misfire. I changed the plugs and wires with no effect. I thought I had it narrowed down to the coil or injector until my wife noticed a new wrinkle.
Under normal driving conditions the misfire is annoying, but my wife found that if she turns on the A/C, it is undriveable and will not accelerate past 30 mph without some patience and a neck brace for the bucking. My first thought was the A/C compressor was freezing up. I turned off the A/C and left the blower on and it would not stop missing. I turn off the blower and it smooths right out to the annoyance I described first.
Right now I drive the car without A/C and blower whenever I accelerate. If I'm going a steady speed, all is well and I can run the blower and A/C.
View 7 Replies
Advertisement
I have a 2000 Explorer 4.0 SOHC that I'm having a persistent problem of cylinder 3 misfire. I've changed plugs with Motorcraft plugs set to the proper gap, put on new wires and have checked the resistance across the ignition module, both primary and secondary without change. I doubt that the problem could be the ignition control module as only cylinder 3 is affected. I have Auto Enginuity that I use to read the codes, attempt a repair and then clear the codes only to have P0303 appear again. Obviously the engine stumbles and has poor acceleration.
View 14 Replies
Well, I have been through the tech folder and all over the forum reading but cant seem to come up with a good first step. When i accelerate the truck shakes, by the sound it seems that its missing a cylinder. I guess it could also be the motor mounts. Besides replacing the plugs and coils, is there something else that could remedy a misfires or dead cylinder?
View 7 Replies
I have an 02 Accent 1.5L that has a misfire on #3. I have replaced the head gasket, valve cover and gasket, intake gasket, timing belt, yes it was top dead center, MAF, Charcoal canister sensor, MAF, plugs, wires, coil pack, injector #3, and the compression in #3 is 130. What else to check. No other codes.
View 3 Replies
After almost an entire year of trouble-free running (with the exception of replacing a ground strap), my 2009 accent decided to start bucking and shuddering again. It only does this when warmed up, runs perfect cold. In the last 16 months, I've replaced the plugs, coils, battery, PCV valve, and ground strap. Car starts with zero hesitation.
Strong battery and starter, consistent output from alternator. After @5 miles, the car stumbles on acceleration, and idles sporadically. While looking at it tonight, I noticed a few exhaust brackets under the car had broken, and the flex section of the intermediate pipe had torn open. Could this presumed exhaust leak be causing the crap running performance?
My "exhausted" brain thought it could cause the O2 sensor to misinform the ECM, resulting in the P0300 code I pulled...
View 3 Replies
My VR6 is making a ticking sound when i accelerate, between 2800-3100, then it dies down a little and then gets loudest at about 3600-4000. The noise stops at exactly 4000rpms every time. Here is a sound clip of what the noise sounds like... you can hear it best in the last 15 seconds or so in the video. Maybe its the timing chains...
[URL] .....
View 19 Replies
Car threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 Replies
My 02 F150 4.6 has 84K miles on it, and started stumbling/hesitating during accellartion about three weeks ago. Before this problem started (about 2,000 miles ago), I installed a new fuel filter and air filter. Since I noticed the problem, I installed new plugs. The problem didn't go away, so today I checked the fuel pressure. At idle the pressure is 32psi with the vacuum line left on the fuel pressure regulator (30-45 is normal as per Chilton's), and 42 with the vacuum line off (40-50 is normal as per Chilton's). I also had someone else rev the engine so I could observe, and found that the fuel pressure went as low as 28 when the engine speed was quickly increased. The standing fuel line pressure is 30 (30 is normal as per Chilton's) Does this sound like a fuel pump problem, or is there something else that I'm missing.
View 10 Replies
Recently I was driving on the highway, about 70 miles into my trip, when all of a sudden my cruise control kicked out and the rpms went high and then I lost acceleration. I pulled over to the berm and tried to take off. Problem is I could not get the car past 30mph because the accelerator pedal could. not be pushed down more than an inch or two no matter how hard I pushed. What could be wrong???
View 1 Replies
I have a 2001 Acura MDX automatic transmission that at least once a day when driving around town, will suddenly loose power, RPM's seem to be stuck at 2000, and then surge up to 5000 with no forward motion. When I try to accelerate again, the car "stumbles" forward until the RPM's settle back down to between 1-3 and the car drives normal. This is creeping me out...any thoughts? Valves have been adjusted.
View 10 Replies
I have a 2000 Ford Focus with new battery and cables, new alternator, less than 100,000 (barely). Recently made a trip from austin to dallas and back. On the way back, on the interstate, car suddenly refused to continue acceleration (no indicator lights came on); pulled to the shoulder, shut everything off; waited about five minutes, car started up on first try..continued driving; about 12 miles later, same thing occurred. Pulled over, turned everything off, started up again just fine, drove the rest of the way home.
Took it to my mechanic, he ran diagnostics..found nothing. Ran perfectly on short drives around town for three weeks; three weeks later, another road trip...did not run air conditioner or anything extra on the drive; about 30 miles from final destination, same thing...lost speed, wouldn't accelerate, pulled over, shut it off...started right up again and ran fine to final destination. On the way home, about 100 miles into return trip, same thing.. lost acceleration etc. But this time would only keep running correctly for about 20 or so miles each time. Was happening so frequently, had it towed home. Got home, started right up, drove fine. the only thing my mechanic noted on last inspection was the AC would not turn off. Could this be an electrical or switch problem?
View 4 Replies
I was running in a track day at Sebring today and missed a shift. Rookie move...the car eventually went into limp mode. I took the car back to the pits and scanned the codes. Limp mode was confirmed in addition to a cylinder 4 misfire and a random/intermittent misfire. Cleared the codes and went back out; couldn't even finish the lap before the car was thrown back into limp mode.
I was able to hobble home by keeping the car out of boost and started trouble shooting. So far I have ruled out spark plugs and coils. Should I be looking at the injector next? Any chance I bent a valve? The misfire can be triggered by putting the car under a load and bringing it up to 5,000 RPMs or higher.
View 24 Replies
I've been having a cylinder 2 misfire in my V6 2002 Solara, and I'm not sure what to replace. I've been told that I should get a new coil pack for cylinder 2. The misfires in the engine seem to be most noticeable under hard acceleration. I'm really not sure what to do.
View 2 Replies
Ford Focus 2004 manual 150K miles. Most days the car runs fine. Other days it will start and run until it warms up, then stumbles or hesitates at speed. When this happens the headlights and dash lights are also flickering. Sometimes i hear a clicking sound behind dash, left side. I have the sure cure: turn the heater fan to high. This works every time. When the engine is hesitating, i turn the fan to 4-high, the engine smooths out. Turn the fan down, engine again hesitates. Hesitates at 3, worse at 2, worst at 1. It seems to need the extra load.
But after few minutes of high heater fan, the alternator light comes on. I flick the heater switch down, endure the hesitation for a few seconds, the alternator light goes out, engine still hesitating, flick the fan to high, engine smooths out. A few months ago i could get it to fun smoothly with the fan on 3, didn't need 4-high. Now seems to need 4.On the days when it is always running smoothly, the heater fan can be on any speed, the alternator light does not come on.
Next few days or even weeks the engine will run smoothly, no hesitation, with the fan on or off or any setting.
The car has been to three shops in past year, one of them a major Ford dealer, who kept it two weeks. The problem has been diagnosed as battery (replaced), Battery connections (checked), plugs (replaced), fuel pump controller (replaced), fuel pump (replaced - ouch!), alternator (replaced twice - ouch twice), grounds (checked). Every time they "fix" something the car runs ok for a week or so.OBD shows P2004 (intake manifold runner stuck) but all agree it can't be the problem.
There have been a few times when i flicked the heater fan to high that all the dash lights died, fan went off, headlights off, turn signals didnt' work, but the engine ran smoothly. Not so good on the highway at night!There have been a few time, not recently, when the car wouldn't start. No dome lights, no dash lights with key turned to ON, no clicking or starter with key turned to START. It acted as if my battery was missing. The cure was to turn the headlights on. All normal after that.
View 19 Replies
For the past few days I've been trying to track down the problem with my '02 Ford Escort. First thing I did was change the spark plugs which smoothed out the engine some, but I still have the PO304 (misfire #4 cylinder). Next I swapped the plug wires between #3 and #4 and reset the ECU hoping the code would come back PO303 (misfire #3 cylinder), yet it still set a code for cylinder #4 meaning the plug wires were good. I then tested the coil and camshaft position sensor which both tested good.
After this I checked the compression on #4 and it was good at 175 PSI. When I removed the #4 plug to test the compression it was gas soaked so the injector is firing, but apparently not the plug. My Chilton's manual says the center pin (ignition/start/run) on the wiring harness for the coil should have 10 volts with the ignition switch in the off position. I checked this and only had 0.1 volts. Where this wire receives it's voltage from and able to tell me more about what to look for or test? I never expected to have so much problem finding a cylinder misfire.
View 14 Replies
I started feeling a slightly rough idle three days ago and yesterday the check engine light illuminated. When we read the OBD, it indicated a Cyl #1 misfire. Question is this. Can I replace a single coil pack (1/cyl), or do I ahve to replace all 8 as a set and why? 2000 Ford Expedition 5.4 L cyl misfire.....
View 4 Replies
This has been an issue for about 8 months now. I'm getting a misfire on cylinder 4. So far compression test, new gas filter, fuel injectors cleaned, spark plugs and wires replaced. coil pack replaced. Heater valve was leaking but was replaced.
View 10 Replies
OK, got a check engine light today when I fired up the Ranger.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use?
Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
View 6 Replies
My parents 2000 Ranger has an CEL for cylinder 4 misfire, but it will clear on its own and then start up days/weeks later, is this common? Could it be an injector?
View 3 Replies
I have a misfire mystery going on in my girlfriends 00 ranger. What is going on, is there is an intermittent misfire on #4. I have an ultra gauge hooked to it, so most of the time when it does it, it will flash a pending code. A lot of the time, the pending code will go away, but sometimes it will set the PO304 code.
First I tried a tune up. New plugs and wires, air cleaner, cleaned out the throttle body. This cured it, for a short while. Then we were back to the pending code / setting code for #4.
When I pull the plug on #4 it is sometimes wet with gas. If you put a new plug in it runs fine for a while. In fact the last time we took a several 100 mile trip with it right after plug change, and it ran great. The pulled plugs re always in good condition with no burn, oil, chips or glazing. I have been using the standard autolites that are in advance auto's computer for that engine. No issues with the other 5 so I figure they re good enough.
The day after we came back I get the call... Honey its doing it again. Often to the point of having no power at all.
But it will clear itself usually, if not a new plug for #4 will cure it immediately.
So I thought something is killing this plug.... Or flooding it. SO I ran 2 cans of sea foam though it, put in a new plug and an new wire. It fixed it for a week then it did it again.
Ok I think... maybe the coil pack is bad either killing the plug or just not firing it at all? So since the pack has never been change in its nearly 300K life (to my knowledge, shes had the truck since about 60K) What the heck.... a new coil pack for the old thing.
I have not had the chance to clean the MAF but we are talking misfire on one cylinder, every now and then with no real conditions that set it off. More often than not its a pending code that you can even hear or feel and other times its a full blown miss that drags the truck down. Well for a short while until it clears up or I replace the plug.
3 cans of seafoam surely would have cleared a sticky injector. I realize it could be a bad wire to that injector but I have not had the time to tear the fiddle bits off to get to it to clean and test it... or just replace it.
Honestly Ive had a lot of cars and trucks, I don't remember ever having to replace an injector. Ive had bad wires to them but they misbehave ALL the time. This problem is so intermittent its freaky.
She says it does it mostly when its cold or not totally warmed up. Almost always, by the time the engine is hot it goes away.
And hot for this truck is over 185F, which I think its too cold to be running and the thermostat needs changed BUT she thinks cool=good. I keep telling her no, cool is often not good, the engine needs to be up to the operating temp.... which to me means 190-200. Her ranger runs between 170-180 all the time. I doubt thats causing the problem but still.... I think new thermo is in order.
My thinking is since it runs so cool all the time, the issue might be related to a spike in the temp over 180 ish, that gods forbid is opening a crack somewhere to suck air or lose compression.
And a compression test is my next step on #4 if/when it does it again. Now I have had cracked valves before, I don't recall them acting this way. After all sometimes the thing will go 100s of miles under different driving conditions and run fine. I don't think a cracked valve would be that nice.
Shes getting @18 MPG mixed driving, when it runs t runs like a bear. It always fires right up. There is no smoke, white or black. There is no water in the oil, no oil in the water. No audible exhaust leaks. No ticks knocks or oddball noises. For its age and miles almost 300K it runs perfectly.
Well until it has its intermittent issue with the misfire, that isnt bad enough to actually set the code.
View 14 Replies
My car is misfiring, as in acceleration 90% sputters until I lay the pedal to the ground, which obviously isn't good for my gas. What do I do? I can't find anything online and I don't want to be throwing money into things that don't work.
View 4 Replies
